2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Mar 2016

Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine rpm of approximately 1,000 for 5 to 6 minutes to circulate the refrigerant and collect compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Using SST, let the refrigerant gas out.

    SST
    07110-58060   (07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE NO. 1 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Remove the 4 bolts and No. 1 engine under cover.


4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    A316609E01

    Text in Illustration 
    *1
    Bleeder Plug
    *2
    Radiator Reservoir Cap Sub-assembly
    *3
    Radiator Reservoir Assembly
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block drain cock plug (on the engine oil cooler cover), and drain the engine coolant.

  1. Tighten the radiator drain cock plug.

  1. Tighten the cylinder block drain cock plug (on the engine oil cooler cover).

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. REMOVE FRONT DOOR SCUFF PLATE RH
  1. Disengage the 5 clips and remove the front door scuff plate RH.


6. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


7. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet and remove the engine service hole sub cover.


8. REMOVE NO. 2 ENGINE SERVICE HOLE COVER
  1. Detach the clips and fold back the carpet.

  1. A151559
    Remove the 3 bolts and No. 2 engine service hole cover.


9. REMOVE FENDER APRON MUDGUARD SEAL RH
  1. Disengage the 3 clips and remove the fender apron mudguard seal RH.


10. REMOVE NO. 1 RADIATOR HOSE

11. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A231913
    Remove the 2 bolts and disconnect the vane pump oil reservoir.


12. LOOSEN FAN PULLEY
  1. Loosen the 4 nuts from the fan pulley.


13. REMOVE FAN AND GENERATOR V BELT

  1. A156649E01
    Remove the drive belt by rotating the tensioner pulley clockwise to loosen its tension with the pulley set bolt of the tensioner.


14. REMOVE FAN PULLEY
  1. Remove the 4 nuts and fan pulley.


15. DISCONNECT NO. 1 AIR CLEANER HOSE

  1. A153649
    Pull the stopper upward and disconnect the No. 1 air cleaner hose from the compressor inlet elbow.


16. REMOVE AIR TUBE ASSEMBLY

  1. A272217
    Loosen the 2 hose clamps.

  1. Remove the 2 bolts, air tube assembly and No. 1 air cleaner hose.


17. REMOVE COMPRESSOR OUTLET ELBOW

  1. A313566
    Loosen the 2 hose clamps and remove the bolt and compressor outlet elbow.


18. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)

  1. E104243
    Remove the bolt and disconnect the cooler refrigerant discharge hose from the compressor and magnetic clutch.

  1. Remove the O-ring from the cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


19. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Air Conditioning System)

  1. E104244
    Remove the bolt and disconnect the cooler refrigerant suction hose.

  1. Remove the O-ring from the cooler refrigerant suction hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.


20. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
  1. Disconnect the connector.

  1. E104245
    Remove the 4 bolts and compressor and magnetic clutch.


21. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A102453E01
    Remove the 4 bolts and No. 1 compressor mounting bracket.


22. REMOVE NO. 2 IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.


23. REMOVE GENERATOR BRACKET

  1. A102712E01
    Remove the 2 bolts, then remove the generator bracket.


24. REMOVE GENERATOR ASSEMBLY

  1. A113682E01
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and generator.


25. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A102857
    Remove the 4 bolts and V-ribbed belt tensioner.


26. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the wire harness clamp.

  1. A156650
    Remove the 6 bolts, 6 washers and timing belt cover.


27. REMOVE TIMING BELT

  1. A070549E05
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.

  1. A070550E01
    Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.

  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.


28. REMOVE NO. 4 AIR HOSE (w/ DPF)

  1. A231914
    Loosen the 2 hose clamps.

  1. Remove the No. 4 air hose.


29. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ DPF)

  1. w/o DPF:

    1. A177101
      Disconnect the diesel turbo pressure sensor connector and vacuum switching valve connector.

    2. Remove the bolt and disconnect the wire harness clamp.

  1. Disconnect the 2 diesel throttle body connectors.

  1. A257142E01
    Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.


30. DISCONNECT ENGINE WIRE (w/ DPF)

  1. A231938
    Detach the 3 clamps and disconnect the water by-pass hose and oil return hose.

  1. A239505
    Detach the clamp and disconnect the glow plug connector.

  1. Detach the clamp and disconnect the engine wire from the No. 1 timing belt cover.

  1. Disconnect the 7 connectors.

  1. Remove the 7 bolts and disconnect the engine wire.

    A239522

  1. Disconnect the 4 connectors and detach the 3 clamps.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire from terminal B.

  1. Remove the bolt and disconnect the engine wire.

    A239558E01

  1. Fold back the floor carpet.

  1. A317701
    Remove the bolt.

  1. Detach the clamp.

  1. A314923
    Disconnect the ECM connector (Click here).

  1. Disconnect the 5 connectors.

  1. Detach the 5 clamps.


31. REMOVE INJECTION PIPE SUB-ASSEMBLY (w/ DPF)

  1. A231933
    Remove the 3 bolts and 3 No. 2 injection pipe clamps.

  1. A231934
    Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.


32. REMOVE VACUUM CONTROL VALVE SET (w/ DPF)

  1. A233171
    Disconnect the vacuum control valve connector and 2 vacuum hoses from the No. 3 vacuum transmitting pipe sub-assembly.

  1. Remove the bolt and vacuum control valve set.


33. DISCONNECT NO. 5 WATER BY-PASS HOSE (w/ DPF)

A239510

34. REMOVE FUEL INLET PIPE SUB-ASSEMBLY (w/ DPF)

NOTICE:
If a No. 1 injection pipe clamp is removed from the fuel inlet pipe, replace the No. 1 injection pipe clamp with a new one.

  1. A239511
    Remove the 2 bolts and 2 No. 1 injection pipe clamps.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


35. REMOVE COMMON RAIL ASSEMBLY (w/ DPF)

  1. A239509
    Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the pressure discharge valve or fuel pressure sensor.


36. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ DPF)

A233168

37. REMOVE NO. 1 CYLINDER HEAD COVER SILENCER (w/ DPF)

  1. A239508
    Remove the No. 1 cylinder head cover silencer from the cylinder head cover.


38. REMOVE INJECTION PIPE SUB-ASSEMBLY (w/o DPF)

  1. A239564
    Disconnect the 4 injector connectors.

  1. Remove the 4 bolts and detach the 3 clamps.

  1. A151629
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A151628
    Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.


39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A060180J01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. A231937
    Remove the 10 bolts, 2 nuts, cylinder head cover and the cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


40. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A070696E01
    Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.


41. REMOVE CAMSHAFT TIMING PULLEY

  1. A100848
    Remove the bolt and camshaft timing pulley while holding the camshaft with a wrench.

  1. A323634E01
    Using SST, remove the camshaft timing pulley and set key.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-05010, 09957-04010)
    09955-04150  

  1. A070551E02
    Rotate the crankshaft approximately 90° counterclockwise from TDC to lower the piston.


42. REMOVE NO. 2 TIMING BELT COVER

  1. A051300E01
    Remove the nut, 4 bolts and No. 2 timing belt cover.


43. REMOVE WATER PUMP ASSEMBLY

  1. A051307
    Remove the 5 bolts, 2 nuts and water pump assembly.

← COMPONENTS (from Oct 2014)REMOVAL (Apr 2016 – Dec 2016) →