2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the resistance.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      20°C (68°F)
      11.6 to 12.4 Ω

      If the result is not as specified, replace the fuel injector assembly.


INSPECT INJECTION VOLUME AND LEAKAGE

CAUTION:
  1. This test involves high-pressure fuel and electricity.
  2. Take every precaution regarding safe handling of both the fuel and the electrical parts.
  3. Perform this test in a safe area, and avoid any sparks or flame.
  4. Do not smoke.

  1. A269129E02
    Assemble SST as shown in the illustration.
    SST
    09268-31014   (09268-41091, 09268-41120, 09268-41500, 09268-41700, 95336-08070)
    Text in Illustration 
    *a
    SST (Fuel Tube Connector)
    *b
    SST (Hose)
    *c
    SST (3 Way)
    *d
    SST (Union No. 7)
    *e
    SST (Hose Band)

  1. Discharge the fuel system pressure (Click here).

  1. Disconnect the No. 1 fuel hose (fuel tube connector) from the fuel tube.

  1. Remove the 2 bolts and disconnect the fuel pressure regulator assembly from the fuel delivery pipe sub-assembly.

    NOTICE:
    Do not disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.

  1. A264461E03
    Connect SST to the fuel tube.
    Text in Illustration 
    *1
    Fuel Tube
    *a
    SST (Fuel Tube Connector)

    CAUTION:
    Always read the precautions (Click here) before connecting the fuel tube connector (quick type).

  1. A088655E01
    Connect SST to the fuel pressure regulator assembly with the 2 bolts.
    SST
    09268-31014   (09268-41091, 09268-41700, 95336-08070)

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Install the O-ring to the fuel injector assembly.

  1. A264463E03
    Assemble SST as shown in the illustration.
    SST
    09268-31014   (09268-41110, 09268-41310, 09268-41700, 95336-08070)
    Text in Illustration 
    *a
    SST (Hose Band)
    *b
    SST (Adapter)
    *c
    SST (Hose)
    *d
    SST (Clamp)
    *e
    Vinyl Tube

    NOTICE:
    Make sure that SST (adapter) and SST (clamp) are not loose and do not rattle.

  1. A264464E04
    Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).
    SST
    09268-31014   (09268-41800)
    Text in Illustration 
    *a
    SST (Tie Band)
    *b
    Lock

    NOTICE:
    1. As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.
    2. Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.

    HINT:
    When removing SST (tie band), disengage the lock.

  1. Check that SST (clamp) and SST (adapter) cannot be easily separated.

  1. Install a vinyl tube to the fuel injector assembly.

  1. Put the fuel injector assembly into a graduated cylinder.

    NOTICE:
    Install a suitable vinyl tube onto the fuel injector assembly to contain the gasoline spray.

  1. Operate the fuel pump.

  1. A099420E03
    Connect SST (EFI inspection wire H) to the fuel injector assembly and the battery for 15 seconds, and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.
    SST
    09842-30080  

    Result:
    Volume
    Difference between each injector
    71 to 86 ml
    15 ml or less

    NOTICE:
    Always turn the voltage on and off on the battery side, not the fuel pump side.

    If the result is not as specified, replace the fuel injector assembly.

  1. A087750E01
    Check the fuel leakage.

    1. In the condition above, disconnect the test probes of SST (EFI inspection wire H) from the battery and check the fuel leakage rate from the fuel injector assembly.

      Standard fuel drop:
      1 drop or less per 12 minutes

← REMOVAL (from Jan 2017)INSPECTION (from Jan 2015) →