2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. DISCONNECT NEGATIVE BATTERY CABLE

2. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


3. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE ENGINE SERVICE HOLE SUB COVER ASSEMBLY
  1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.


6. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

  1. C101999E01
    Remove the 2 bolts and vane pump oil reservoir assembly.

    NOTICE:
    Suspend the vane pump oil reservoir assembly with wire to prevent power steering fluid from spilling out.


7. DISCONNECT OIL RETURN HOSE (w/ Inter cooler)

  1. A106042
    Loosen the clip.

  1. Disconnect the oil return hose from the intake manifold.


8. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)

  1. A106043
    Disconnect the fuel pressure sensor connector.

  1. A106844
    Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


9. REMOVE AIR HOSE NO.4

  1. A102281
    Loosen the 2 clamps.

  1. Remove the air hose No.4.


10. REMOVE DIESEL THROTTLE BODY ASSEMBLY

  1. A102282
    Disconnect the 2 throttle body connectors.

  1. A102902
    Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.

  1. Remove the gasket from intake air connector.


11. REMOVE ENGINE SERVICE HOLE COVER NO.2

  1. A113043
    Roll up the carpet.

  1. Remove the 3 bolts and the engine service hole cover No.2.


12. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve)

  1. A106846
    Remove the bolt, and separate the manifold stay.

  1. Disconnect the vacuum hose from intake air connector.

  1. A106848E01
    Remove the bolt, 2 nuts and the intake air connector assembly.

  1. Remove the 2 gaskets and intake air connector No.2 from the intake air connector.


13. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)

  1. Remove the vacuum regulating valve.

    1. A103046
      Remove the 2 vacuum hoses and the vacuum regulating valve connector.

    2. Remove the 2 bolts and the vacuum regulating valve.

  1. Remove the EGR valve assembly with the sensor.

    1. A115757
      Remove the bolt, and separate the manifold stay.

    2. Disconnect the vacuum hose from the intake air connector.

    3. A103043
      Disconnect the intake air temperature sensor connector.

    4. Disconnect the EGR valve position sensor connector.

    5. A115761E01
      Remove the bolt, 2 nuts and the intake air connector assembly.

    6. Remove the 2 gaskets and EGR valve assembly from the intake air connector.


14. REMOVE OIL LEVEL GAUGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and oil level gauge guide.


15. REMOVE INJECTION PIPE
SST
09023-12701  

  1. Remove the injection pipe.

    1. A103526
      Remove the 2 nuts and injection pipe clamp No.3.

    2. A103532
      Using SST, remove the 4 injection pipes.
      SST
      09023-12701  


16. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Using SST, remove the fuel inlet pipe sub-assembly.

    SST
    09023-12701  


17. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY NO.2

  1. A103528
    Remove the union bolt and gasket.

  1. A103527
    Remove the 2 bolts and the nozzle leakage pipe assembly No.2.


18. REMOVE INTAKE MANIFOLD
  1. Remove the bolt, nut, and the manifold stay.

  1. Remove the bolt, and disconnect the ground cable.

  1. A103060
    Remove the 4 bolts, 2 nuts, and intake manifold.

  1. Remove the gasket from the cylinder head.


19. REMOVE GLOW PLUG NO.1 CONNECTOR
  1. Remove the 4 grommets.

  1. Remove the 4 nuts and glow plug No.1 connectors.


20. REMOVE GLOW PLUG
  1. Using a deep socket wrench (12 mm), remove the 4 glow plugs.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →