INSTALLATION
Removal / installation · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
| 1. INSTALL THERMOSTAT |
Install a new gasket on the thermostat.
Install the thermostat with the jiggle valve upward.
- HINT:
- The jiggle valve should be within -15 to +15° from the uppermost position
| 2. INSTALL WATER OUTLET |
Install the water outlet with the 3 bolts.
- Torque:
- 19 N*m{ 195 kgf*cm , 14 ft.*lbf }
| 3. INSTALL RADIATOR HOSE NO.4 |
| 4. INSTALL RADIATOR HOSE INLET |
| 5. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY |
Install the 5 bolts and engine service hole cover.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 6. INSTALL FRONT DOOR SCUFF PLATE RH |
| 7. INSTALL FRONT SEAT RH |
Connect the front seat inner belt assembly connector and install the front seat assembly.

Align the front seat assembly adjuster pin with the holes in the body.
Move the front seat assembly to the rearmost position.
- NOTICE:
- Make sure that the front seat assembly is securely locked.
Temporarily tighten the 2 bolts on the front side of the front seat assembly.
Move the front seat assembly fully forward.
- NOTICE:
- Make sure that the front seat assembly is securely locked.
Temporarily tighten the 2 bolts on the rear side of the front seat assembly.
Move the front seat assembly to the rearmost position.
- NOTICE:
- Make sure that the front seat assembly is securely locked.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
Move the front seat assembly fully forward.
- NOTICE:
- Make sure that the front seat assembly is securely locked.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
| 8. ADD ENGINE COOLANT |
Fill the radiator reservoir assembly with coolant to the top of the inlet.
- Standard Capacity:
Item
Specified Condition
w/o Heater
12.3 liters (13.0 US qts, 10.8 Imp. qts)
w/ Front Heater
13.3 liters (14.1 US qts, 11.7 Imp. qts)
w/ Front and Rear Heaters
15.3 liters (16.2 US qts, 13.5 Imp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- Use of improper coolants may damage the engine cooling system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper coolants may damage the engine cooling system.
Add coolant up to the B line mark in the radiator reservoir assembly and install the reservoir cap.

Warm up the engine until the thermostat opens.
While the thermostat is open, circulate the coolant for several minutes.
- HINT:
- The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.
After the engine cools down, check that the coolant level is between the LOW and FULL level marks.

| 9. START THE ENGINE |
| 10. CHECK FOR ENGINE COOLANT LEAKS |
