2014-2019 Hiace · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from Jan 2017


INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. C322245
    Using a caliper gauge, measure the inside diameter of the direct clutch drum sub-assembly bushing.

    Standard inside diameter:
    59.515 to 59.540 mm (2.3431 to 2.3440 in.)

    If the inside diameter is not as specified, replace the direct clutch drum sub-assembly.


INSPECT INPUT SHAFT SUB-ASSEMBLY

  1. C322244
    Using a caliper gauge, measure the inside diameter of the input shaft sub-assembly bushing.

    Standard inside diameter:
    20.000 to 20.025 mm (0.7874 to 0.7883 in.)

    If the inside diameter is not as specified, replace the input shaft sub-assembly.


INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. D028501E01
    Using a caliper gauge, measure the inside diameter of the forward clutch hub sub-assembly bushing.

    Standard inside diameter:
    26.037 to 26.062 mm (1.02508 to 1.02606 in.)

    If the inside diameter is not as specified, replace the forward clutch hub sub-assembly.


INSPECT SUN GEAR INPUT DRUM SUB-ASSEMBLY

  1. C322224
    Using a caliper gauge, measure the inside diameter of the sun gear input drum sub-assembly bushing.

    Standard inside diameter:
    35.811 to 35.835 mm (1.4099 to 1.4108 in.)

    If the inside diameter is not as specified, replace the sun gear input drum sub-assembly.


INSPECT FRONT PLANETARY GEAR ASSEMBLY

  1. C322225
    Using a caliper gauge, measure the inside diameter of the front planetary gear assembly bushing.

    Standard inside diameter:
    35.811 to 35.835 mm (1.4099 to 1.4108 in.)

    If the inside diameter is not as specified, replace the front planetary gear assembly.


INSPECT FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C322243
    Using a caliper gauge, measure the inside diameter of the front planetary ring gear flange sub-assembly bushing.

    Standard inside diameter:
    54.038 to 54.063 mm (2.1275 to 2.1284 in.)

    If the inside diameter is not as specified, replace the front planetary ring gear flange sub-assembly.


INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. D028531E01
    Using a caliper gauge, measure the inside diameter of the rear planetary ring gear flange sub-assembly bushing.

    Standard inside diameter:
    32.176 to 32.201 mm (1.2668 to 1.2677 in.)

    If the inside diameter is not as specified, replace the rear planetary ring gear flange sub-assembly.


INSPECT CENTER PLANETARY GEAR ASSEMBLY

  1. C321248
    Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.00473 to 0.0267 in.)

    If the clearance is not as specified, replace the center planetary gear assembly.


INSPECT REAR PLANETARY GEAR ASSEMBLY

  1. C109349
    Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the rear planetary gear assembly.

  1. C109350
    Using a caliper gauge, measure the inside diameter of the rear planetary gear bushing.

    Standard inside diameter:
    20.000 to 20.025 mm (0.7874 to 0.7883 in.)

    If the inside diameter is not as specified, replace the rear planetary gear assembly.


INSPECT NO. 3 ONE-WAY CLUTCH ASSEMBLY

  1. D028532E08
    Hold the rear planetary ring gear and turn the No. 3 one-way clutch assembly.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free

  1. Check that the No. 3 one-way clutch assembly turns freely when turned counterclockwise and locks when turned clockwise.
    If there is a problem with the No. 3 one-way clutch assembly, replace it.


INSPECT INTERMEDIATE SHAFT

  1. D028529E06
    Using a dial indicator, check the intermediate shaft runout.

    Standard runout:
    0.03 mm (0.00118 in.)

    If the runout is more than the standard, replace the intermediate shaft with a new one.

  1. C321242E01
    Using a micrometer, check the outer diameter of the intermediate shaft at each point shown in the illustration.

    Standard diameter:
    A:
    32.062 to 32.075 mm (1.2623 to 1.2627 in.)
    B:
    25.962 to 25.975 mm (1.0222 to 1.0226 in.)
    C:
    19.963 to 19.976 mm (0.7860 to 0.7864 in.)

    If the outer diameter is more than the standard, replace the intermediate shaft with a new one.


INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the forward clutch return spring sub-assembly including the spring seat.

    Standard free length:
    26.74 mm (1.053 in.)

    If the free length is more than the standard free length, replace the forward clutch return spring sub-assembly.


INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the direct clutch return spring sub-assembly including the spring seat.

    Standard free length:
    22.14 mm (0.872 in.)

    If the free length is more than the standard free length, replace the direct clutch return spring sub-assembly.


INSPECT NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the No. 1 brake piston return spring sub-assembly including the spring seat.

    Standard free length:
    16.72 mm (0.658 in.)

    If the free length is more than the standard free length, replace the No. 1 brake piston return spring sub-assembly.


INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the No. 2 brake piston return spring sub-assembly including the spring seat.

    Standard free length:
    16.68 mm (0.657 in.)

    If the free length is more than the standard free length, replace the No. 2 brake piston return spring sub-assembly.


INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D029830E01
    Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly including the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)

    If the free length is more than the standard free length, replace the 1st and reverse return spring sub-assembly.


INSPECT NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)

  1. C322924
    Check if the contact surfaces of the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 1 clutch disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 1 clutch discs.
    2. Before installing new No. 1 clutch discs, soak them in ATF for at least 15 minutes.


INSPECT NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

  1. C322925
    Check if the contact surfaces of the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 2 clutch disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 2 clutch discs.
    2. Before installing new No. 2 clutch discs, soak them in ATF for at least 15 minutes.


INSPECT NO. 1 BRAKE DISC

  1. C322922
    Check if the contact surfaces of the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 1 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 1 brake discs.
    2. Before installing new No. 1 brake discs, soak them in ATF for at least 15 minutes.


INSPECT NO. 2 BRAKE DISC

  1. C322923
    Check if the contact surfaces of the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 2 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 2 brake discs.
    2. Before installing new No. 2 brake discs, soak them in ATF for at least 15 minutes.


INSPECT NO. 4 BRAKE DISC

  1. C322921
    Check if the contact surfaces of the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 4 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 4 brake discs.
    2. Before installing new No. 4 brake discs, soak them in ATF for at least 15 minutes.


INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH)

  1. C321225E01
    Using a dial indicator, measure the clearance of the No. 1 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.75 to 1.05 mm (0.0295 to 0.0413 in.)

    Text in Illustration 
    *1
    Selected Forward Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate forward clutch flange that will bring the clearance within the specified range.

    HINT:
    There are forward clutch flanges of different thicknesses.

    Forward Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35635-71010
    3.0 (0.118)
    35635-71020
    3.1 (0.122)
    35635-71030
    3.2 (0.126)
    35635-71040
    3.3 (0.130)
    35635-71050
    3.4 (0.134)
    35635-71060
    3.5 (0.138)
    35635-71070
    3.6 (0.142)
    35635-71080
    3.7 (0.146)
    35635-71090
    3.8 (0.150)
    35635-71100
    3.9 (0.154)
    35635-71110
    4.0 (0.157)
    35635-71120
    4.1 (0.161)
    35635-71130
    4.2 (0.165)


INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)

  1. C321224E01
    Using a dial indicator, measure the clearance of the No. 2 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.4 to 0.7 mm (0.0157 to 0.0275 in.)

    Text in Illustration 
    *1
    Selected Direct Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate direct clutch flange that will bring the clearance within the specified range.

    HINT:
    There are direct clutch flanges of different thicknesses.

    Direct Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35675-71010
    3.0 (0.118)
    35675-71020
    3.1 (0.122)
    35675-71030
    3.2 (0.126)
    35675-71040
    3.3 (0.130)
    35675-71050
    3.4 (0.134)
    35675-71060
    3.5 (0.138)
    35675-71070
    3.6 (0.142)
    35675-71080
    3.7 (0.146)
    35675-71090
    3.8 (0.150)


INSPECT CLEARANCE OF NO. 1 BRAKE

  1. C321233
    Make sure that the No. 1 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321235E01
    Using a feeler gauge, measure the No. 1 brake pack clearance between the No. 1 brake disc and No. 1 brake flange.

    Standard clearance:
    0.3 to 0.6 mm (0.0119 to 0.0236 in.)

    Text in Illustration 
    *1
    Selected No. 1 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 1 brake flange that will bring the clearance within the specified range.

    No. 1 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    4.9 (0.193)
    1
    5.0 (0.197)
    2
    5.1 (0.201)
    3
    5.2 (0.205)
    4
    5.3 (0.209)
    5
    5.4 (0.213)
    6
    5.5 (0.217)
    7
    5.6 (0.220)
    8
    5.7 (0.224)
    A
    5.8 (0.228)


INSPECT CLEARANCE OF NO. 2 BRAKE

  1. C321232
    Make sure that the No. 2 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321234E01
    Using a feeler gauge, measure the No. 2 brake pack clearance between the No. 2 brake disc and No. 2 brake flange.

    Standard clearance:
    0.4 to 0.7 mm (0.0158 to 0.0275 in.)

    Text in Illustration 
    *1
    Selected No. 2 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 2 brake flange that will bring the clearance within the specified range.

    No. 2 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    2.0 (0.0787)
    1
    2.1 (0.0827)
    2
    2.2 (0.0866)
    3
    2.3 (0.0906)
    4
    2.4 (0.0945)
    5
    2.5 (0.0984)
    6
    2.6 (0.102)
    7
    2.7 (0.106)
    8
    2.8 (0.110)


INSPECT CLEARANCE OF NO. 4 BRAKE

  1. C322242
    Make sure that the 1st and reverse brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321236E01
    Using a feeler gauge, measure the No. 4 brake pack clearance between the No. 4 brake disc and No. 4 brake flange.

    Standard clearance:
    0.5 to 0.8 mm (0.0197 to 0.0314 in.)

    Text in Illustration 
    *1
    Selected No. 4 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 4 brake flange that will bring the clearance within the specified range.

    No. 4 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    1.80 (0.0709)
    1
    1.97 (0.0776)
    3
    2.11 (0.0831)
    4
    2.25 (0.0886)
    5
    2.39 (0.0941)
    7
    2.53 (0.0996)
    8
    2.67 (0.105)
    10
    2.81 (0.111)
    11
    2.95 (0.116)
    12
    3.09 (0.122)
    14
    3.23 (0.127)

← DISASSEMBLY (from Jan 2017)REASSEMBLY (from Jan 2017) →