2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

  1. C160267E01
    Remove the nut, the washer and the transmission control shaft lever LH.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C080254
    Using a screwdriver, unstake the lock washer.

  1. Remove the nut and the lock washer.

  1. C080256
    Remove the bolt and the park/neutral position switch assembly.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


3. REMOVE TEMPERATURE SENSOR (w/ DPF)

C248713
  1. Detach the temperature sensor connector clamp from the wire harness bracket.

  1. Using a 19 mm union nut wrench, remove the temperature sensor from the automatic transmission assembly.

  1. Remove the O-ring from the temperature sensor.


4. REMOVE TEMPERATURE SENSOR (w/o DPF)

  1. C158423E01
    Remove the temperature sensor.

  1. Remove the O-ring from the temperature sensor.


5. REMOVE OIL COOLER TUBE UNION

C248712E01
  1. Remove the 2 oil cooler tube unions.

  1. Remove the O-rings from each oil cooler tube union.


6. REMOVE BREATHER HOSE
  1. Remove the bolt and breather plug hose from the automatic transmission housing.


7. REMOVE SPEEDOMETER SENSOR (w/ Speedometer Sensor)

  1. C300625E01
    Remove the bolt and the speedometer sensor.

  1. C300626
    Remove the speedometer driven gear from the speedometer sensor.

  1. Remove the O-ring from the speedometer sensor.


8. REMOVE SPEED SENSOR NC0

  1. C158425E01
    Remove the bolt and the speed sensor NC0.

  1. Remove the O-ring from the speed sensor NC0.


9. REMOVE SPEED SENSOR SP2

  1. C158426E01
    Remove the bolt and the speed sensor SP2.

  1. Remove the O-ring from the speed sensor SP2.


10. REMOVE AUTOMATIC TRANSMISSION HOUSING

  1. C157840E01
    Remove the 6 bolts.

  1. Remove the automatic transmission housing.


11. FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT05092
    Install the automatic transmission case sub-assembly onto the overhaul attachment.


12. REMOVE EXTENSION HOUSING SUB-ASSEMBLY

  1. C114744
    Remove the 6 bolts.

  1. Remove the extension housing sub-assembly and the extension housing gasket.


13. REMOVE EXTENSION HOUSING BUSH APPLY TUBE GASKET

  1. C114745E06
    Remove the extension housing bush apply tube gasket.


14. REMOVE EXTENSION HOUSING BUSH APPLY TUBE

  1. C114745E07
    Remove the extension housing bush apply tube.


15. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C158427E01
    Using SST, remove the automatic transmission extension housing oil seal.
    SST
    09308-00010  


16. REMOVE EXTENSION HOUSING DUST DEFLECTOR

  1. C114747
    Mount the extension housing sub-assembly in a soft jaw vise.

  1. Using a screwdriver and a hammer, remove the extension housing dust deflector.


17. INSPECT EXTENSION HOUSING SUB-ASSEMBLY

  1. C106501
    Using a cylinder gauge, measure the inside diameter of the extension housing bushing.

    Maximum inside diameter:
    40.03 mm (1.5760 in.)

    If the inside diameter is greater than the maximum, replace the extension housing.


18. REMOVE SPEEDOMETER DRIVE GEAR (w/ Speedometer Sensor)

  1. C158436E01
    Using snap ring expander, remove the snap ring.

  1. Remove the speedometer drive gear and the ball.


19. REMOVE SENSOR ROTOR (w/ Speedometer Sensor)

  1. C158437E04
    Remove the sensor rotor and the key.

  1. Using snap ring expander, remove the snap ring.


20. REMOVE SENSOR ROTOR (w/o Speedometer Sensor)

  1. C114748E04
    Using snap ring expander, remove the rear side snap ring.

  1. Remove the sensor rotor and the key.

  1. Using snap ring expander, remove the front side snap ring.


21. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. C157841E01
    Remove the 19 bolts.

    NOTICE:
    Do not turn the transmission over as this will contaminate the valve body with any foreign matter at the bottom of the automatic transmission oil pan sub-assembly.

  1. Q007487E04
    Insert the blade of an oil pan seal cutter between the transmission case and automatic transmission oil pan sub-assembly, and then cut through the applied sealer.

    NOTICE:
    Be careful not to damage the flanges of the automatic transmission oil pan sub-assembly and transmission case.

  1. Remove the automatic transmission oil pan sub-assembly by lifting the transmission case.


22. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. D001124
    Remove the oil cleaner magnets, and use them to collect steel particles.
    Carefully look at the foreign matter and particles in the pan and on the oil cleaner magnets to anticipate the type of wear you will find in the transmission.

    Steel (magnetic):
    Bearing, gear and clutch plate wear

    Brass (non-magnetic):
    Bushing wear


23. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C114750
    Remove the 4 bolts.

  1. Remove the valve body oil strainer assembly and the 5 gaskets.


24. REMOVE TRANSMISSION WIRE

  1. C158428
    Disconnect the 4 connectors from each shift solenoid valve.

  1. AT05066E03
    Remove the bolt.

  1. Pull out the transmission wire from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the transmission wire.


25. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. D029011E01
    Remove the 20 bolts and the transmission valve body assembly.


26. REMOVE CHECK BALL BODY

  1. AT05098E02
    Remove the check ball body and the spring.


27. REMOVE B-2 ACCUMULATOR PISTON

  1. D006514
    Applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole, remove the B-2 accumulator piston and the spring.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the 2 O-rings from the B-2 accumulator piston.


28. REMOVE C-2 ACCUMULATOR PISTON

  1. D006514
    Applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole, remove the C-2 accumulator piston and the 2 springs.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying the compressed air.

  1. Remove the 2 O-rings from the C-2 accumulator piston.


29. REMOVE B-0 ACCUMULATOR PISTON

  1. D006515
    Applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole, remove the B-0 accumulator piston and the spring.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. Remove the 2 O-rings from the B-0 accumulator piston.


30. REMOVE C-0 ACCUMULATOR PISTON

  1. D006516
    Applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole, remove the C-0 accumulator piston and the 2 springs.

    NOTICE:
    1. The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a shop rag or piece of cloth.
    2. Take care not to splash ATF when applying compressed air.

  1. Remove the O-ring from the C-0 accumulator piston.


31. REMOVE PARKING LOCK PAWL BRACKET

  1. C158429
    Remove the 3 bolts and the parking lock pawl bracket.


32. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. AT05120
    Disconnect the parking lock rod sub-assembly from the manual valve lever sub-assembly.


33. REMOVE PARKING LOCK PAWL SHAFT

  1. Z006720E02
    Pull out the parking lock pawl shaft from the front side, then remove the lock pawl and the spring.

  1. Remove the E-ring from the parking lock pawl shaft.


34. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. Z006721E02
    Using a hammer and screwdriver, cut off the spacer and remove it from the manual valve lever shaft sub-assembly.

  1. AT05105
    Using a pin punch and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it does not fall into the transmission case.

  1. Pull out the manual valve lever shaft through the automatic transmission case sub-assembly, and remove the manual valve lever sub-assembly.


35. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. C158430
    Using a screwdriver, remove the 2 manual valve lever shaft oil seals.


36. REMOVE FRONT OIL PUMP BODY SUB-ASSEMBLY

  1. C158431
    Stand up the transmission.

  1. Remove the 7 bolts.

  1. AT05123E02
    Using SST, remove the front oil pump body sub-assembly.
    SST
    09350-30020   (09350-07020)

  1. Remove the O-ring from the front oil pump body sub-assembly.

  1. C158670E02
    Remove the thrust bearing race from the front oil pump body sub-assembly.


37. REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY

  1. Q000619
    Remove the overdrive planetary gear, overdrive direct clutch and one-way clutch from the automatic transmission case sub-assembly.

  1. C158671E01
    Remove the thrust needle roller bearing and the thrust bearing race from overdrive planetary gear assembly.


38. REMOVE OVERDRIVE PLANETARY RING GEAR

  1. AT05146
    Remove the overdrive planetary ring gear from the automatic transmission case sub-assembly.

  1. C158672E01
    Remove the thrust needle roller bearing and the thrust bearing race from the overdrive planetary ring gear.


39. INSPECT OVERDRIVE BRAKE PISTON

  1. AT05282E02
    Place SST and a dial indicator onto the overdrive brake piston.
    SST
    09350-30020   (09350-06120)

  1. AT05147
    Measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Piston stroke:
    1.40 to 1.70 mm (0.0551 to 0.0669 in.)

    If the piston stroke is less than the limit, parts may be assembled incorrectly, so check and reassemble them if necessary.
    If the piston stroke is still outside the specified range, select another flange.

    HINT:
    There are 7 different thicknesses for the flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    77
    3.3 mm (0.130 in.)
    81
    3.8 mm (0.150 in.)
    78
    3.5 mm (0.138 in.)
    82
    3.9 mm (0.154 in.)
    79
    3.6 mm (0.142 in.)
    83
    4.0 mm (0.157 in.)
    80
    3.7 mm (0.146 in.)
    -
    -


40. REMOVE OVERDRIVE BRAKE PACK

  1. AT05109E02
    Using a screwdriver, remove the snap ring.

    HINT:
    Tape up the screwdriver tip before use.

  1. C158432E01
    Remove the overdrive brake pack.


41. INSPECT PISTON STROKE OF 2ND COAST BRAKE

  1. AT05216E02
    Place a mark on the 2nd coast brake piston rod.

  1. Using SST, measure the stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    SST
    09240-00020  

    Piston rod stroke:
    1.50 to 3.00 mm (0.0591 to 0.1181 in.)

    If the stroke is outside the specified range, replace the piston rod.

    Piston rod length:
    78.4 mm (3.087 in.) or
    79.9 mm (3.146 in.)

    If the stroke is still outside the specified range, replace the 2nd coast brake band assembly with a new one.


42. INSPECT OUTPUT SHAFT

  1. Z006796
    Using a dial indicator, measure the end play of the output shaft by hand.

    End play:
    0.30 to 1.04 mm (0.0118 to 0.0409 in.)

    If the value is outside the standard range, check for improper installation.

  1. Check that the output shaft rotates smoothly.


43. REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY

  1. C158433
    Remove the 2 bolts from the automatic transmission case sub-assembly.

  1. AT05249E02
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07020, 09350-07060)

  1. AT05211E02
    Using SST, remove the overdrive support sub-assembly.
    SST
    09350-30020   (09350-07020)

  1. AT05159
    Remove the clutch drum thrust washer from the overdrive support sub-assembly.

  1. C158673E01
    Remove the thrust needle roller bearing and the thrust bearing race from the overdrive support sub-assembly.


44. REMOVE 2ND COAST BRAKE PISTON

  1. AT05127E02
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05280
    Applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole, remove the 2nd coast brake cover, the 2nd coast brake piston and the spring.

  1. Remove the 2 O-rings from the 2nd coast brake cover.


45. REMOVE DIRECT CLUTCH ASSEMBLY

  1. AT05149
    Remove the direct clutch assembly with the forward clutch assembly from the automatic transmission case sub-assembly.


46. REMOVE FORWARD CLUTCH ASSEMBLY

  1. C158674E01
    Remove the forward clutch assembly from the direct clutch assembly.

  1. C158675E01
    Remove the No. 2 clutch drum thrust washer, thrust needle roller bearing and thrust bearing race from the forward clutch assembly.


47. REMOVE 2ND COAST BRAKE BAND ASSEMBLY

  1. AT05111
    Using a screwdriver, remove the E-ring from the pin.

    HINT:
    Apply grease to the E-ring and the pin before the work so that the ring does not fly out.

  1. Remove the pin from the 2nd coast brake band assembly.

  1. Remove the E-ring from the pin.

  1. Q004030
    Remove the 2nd coast brake band assembly from the automatic transmission case sub-assembly.


48. REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. AT05128
    Remove the front planetary ring gear sub-assembly from the automatic transmission case sub-assembly.

  1. C158676E01
    Remove the 2 thrust needle roller bearings and the thrust bearing race from the front planetary ring gear sub-assembly.

  1. C158677
    Remove the thrust bearing race from the front planetary gear assembly.

  1. Z005131E02
    With wooden blocks or equivalent placed under the output shaft, stand the transmission on the output shaft.


49. INSPECT FRONT PLANETARY RING GEAR SUB-ASSEMBLY

  1. AT08187
    Using a dial indicator, measure the inside diameter of the planetary ring gear bushing.

    Maximum inside diameter:
    24.02 mm (0.9457 in.)

    If the inside diameter is greater than the maximum, replace the planetary ring gear sub-assembly.


50. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. C158678E01
    Using SST, remove the snap ring.
    SST
    09350-30020   (09350-07070)

    HINT:
    Pushing the output shaft towards the front makes it easier to remove the snap ring.

  1. C158679
    Remove the front planetary gear assembly from the automatic transmission case sub-assembly.

  1. C158680E01
    Remove the thrust needle roller bearing and the thrust bearing race from the front planetary gear assembly.
    If necessary, using a screw driver.


51. INSPECT PLANETARY PINION GEAR THRUST CLEARANCE

  1. C158684
    Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.0079 to 0.0236 in.)

    Maximum clearance:
    0.60 mm (0.0236 in.)

    If the clearance is greater than the maximum, replace the planetary gear assembly.


52. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

  1. Q000837E03
    Remove the planetary sun gear sub-assembly and the 1 way clutch from the automatic transmission case sub-assembly.

  1. Remove the No. 4 planetary carrier thrust washer.


53. REMOVE 1 WAY CLUTCH ASSEMBLY

  1. AT08188
    Remove the 1 way clutch assembly from the planetary sun gear sub-assembly.

  1. AT01642
    Remove the No. 2 planetary carrier thrust washer from the planetary sun gear sub-assembly.


54. INSPECT 2ND BRAKE PACK CLEARANCE

  1. AT05215
    Using a feeler gauge, measure the clearance between the snap ring and the flange.

    Standard clearance:
    0.62 to 1.98 mm (0.0244 to 0.0780 in.)

    If the clearance is outside the standard, check for improper installation.


55. REMOVE 2ND BRAKE PACK

  1. AT05476E02
    Using a screwdriver, remove the snap ring.

    HINT:
    Tape up the screwdriver tip before use.

  1. AT05398E05
    Remove the 2nd brake pack.


56. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

  1. AT05212
    Using a feeler gauge, measure the clearance between the plate and the 2nd brake drum.

    Standard clearance:
    0.70 to 1.22 mm (0.0276 to 0.0480 in.)

    If the clearance is outside the standard range, select another flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    67
    5.4 mm (0.213 in.)
    52
    4.6 mm (0.181 in.)
    66
    5.2 mm (0.205 in.)
    53
    4.4 mm (0.173 in.)
    50
    5.0 mm (0.197 in.)
    54
    4.2 mm (0.165 in.)
    51
    4.8 mm (0.189 in.)
    55
    4.0 mm (0.157 in.)


57. REMOVE 2ND BRAKE PISTON SLEEVE

  1. AT05279
    Using a screwdriver, remove the 2nd brake piston sleeve.

    HINT:
    Tape up the screwdriver tip before use.


58. REMOVE REAR PLANETARY GEAR ASSEMBLY

  1. AT05460E02
    Using SST and a screwdriver, remove the snap ring.
    SST
    09350-30020   (09350-07060)

  1. AT05158
    Remove the 2nd brake piston assembly, the 1st and reverse brake pack, the rear planetary gear assembly and the output shaft.

  1. C158682
    Remove the 2nd brake piston assembly.

  1. C158683
    Remove the 1st and reverse brake pack.

  1. AT05107
    Remove the leaf spring.


59. INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

  1. AT06460E02
    Check if the sliding surfaces of the disc, the plate and the flange are worn or burnt. If necessary, replace them.

    HINT:
    1. If the lining of the disc is peeled off or discolored, or even if only a part of the printed numbers is corroded, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


60. REMOVE BRAKE DRUM GASKET

  1. AT04444E01
    Remove the brake drum gasket.


61. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

  1. AT05890
    Make sure that the No. 2 1st and reverse brake piston move smoothly when applying and releasing compressed air into the transmission case.


62. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. AT05132
    Remove the thrust needle roller bearing from the automatic transmission case sub-assembly.

  1. AT08336E02
    Set SST on the spring retainer, and compress the return spring.
    SST
    09350-30020   (09350-07050)

    NOTICE:
    Stop compressing when the spring retainer is lowered to a position 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, preventing the spring retainer from being deformed.

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the 1st and reverse brake return spring sub-assembly.


63. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. Q000777E02
    Check the return spring free length together with the spring seat.

    Standard free length:
    18.39 mm (0.7240 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


64. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON

  1. AT05375
    Hold the No. 2 1st and reverse brake piston by hand, and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 1st and reverse brake piston.
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. Remove the O-ring from the No. 2 1st and reverse brake piston.


65. REMOVE BRAKE REACTION SLEEVE

  1. AT08335E02
    Install SST behind the brake reaction sleeve and gradually lift it out of the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07080)

  1. Remove the O-ring from the brake reaction sleeve.


66. REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON

  1. AT08334E02
    Install SST behind the No. 1 1st and reverse brake piston and gradually lift it out of the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the No. 1 1st and reverse brake piston.


67. INSPECT AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. AT08224
    Using a cylinder gauge, measure the inside diameter of the automatic transmission case rear bushing.

    Maximum inside diameter:
    38.13 mm (1.5012 in.)

    If the inside diameter is greater than the maximum, replace the automatic transmission case sub-assembly.

← COMPONENTS (from Jan 2017)DISASSEMBLY (from Jan 2017) →