2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2017


1. REMOVE BREATHER PLUG HOSE

  1. C367945
    Remove the bolt and breather plug hose from the automatic transmission case sub-assembly.

  1. C320613E01
    Remove the O-ring from the breather plug.
    Text in Illustration 
    *1
    Breather Plug Sub-assembly
    *2
    Clamp
    *3
    Breather Plug Hose
    *4
    Breather Plug
    *5
    O-ring

  1. Remove the breather plug sub-assembly, clamp and breather plug from the breather plug hose.


2. REMOVE TRANSMISSION REVOLUTION SENSOR

  1. C318500
    Remove the bolt and transmission revolution sensor NT from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the transmission revolution sensor NT.

  1. C318501
    Remove the bolt and transmission revolution sensor SP2 from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the transmission revolution sensor SP2.


3. REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

  1. C320636E01
    Remove the nut, spring washer and transmission control shaft lever LH from the park/neutral position switch assembly.


4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C320637
    Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut and the lock washer.

  1. Remove the bolt and park/neutral position switch assembly from the automatic transmission case sub-assembly.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.


5. REMOVE REFILL PLUG

  1. C320629
    Remove the refill plug from the extension housing sub-assembly.

  1. Remove the O-ring from the refill plug.


6. REMOVE AUTOMATIC TRANSMISSION CASE PLUG

  1. C321170
    Remove the 6 automatic transmission case plugs from the automatic transmission case sub-assembly.

  1. Remove the 6 O-rings from the 6 automatic transmission case plugs.

  1. C321171
    Using a T55 "TORX" socket wrench, remove the automatic transmission case plug from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the automatic transmission case plug.


7. REMOVE OIL COOLER TUBE UNION

  1. C321169E01
    Remove the 2 oil cooler tube unions from the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

  1. Remove the 2 O-rings from the 2 oil cooler tube unions.


8. REMOVE EXTENSION HOUSING DUST DEFLECTOR

  1. C321174
    Using a brass bar and hammer, tap out the extension housing dust deflector from the extension housing sub-assembly.

    NOTICE:
    Be careful not to damage the extension housing sub-assembly.


9. REMOVE EXTENSION HOUSING SUB-ASSEMBLY

  1. C367946
    Remove the 8 bolts and extension housing sub-assembly from the automatic transmission case sub-assembly.

    HINT:
    Use a brass bar and hammer to remove the extension housing sub-assembly.


10. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C321177E01
    Using a screwdriver, pry out the automatic transmission extension housing oil seal from the extension housing sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the extension housing sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


11. REMOVE AUTOMATIC TRANSMISSION HOUSING

  1. C324561
    Remove the 12 bolts and automatic transmission housing from the automatic transmission case sub-assembly.


12. SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

  1. C367947
    Install the automatic transmission case sub-assembly to an overhaul attachment.


13. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

NOTICE:
Do not turn the transmission over as this will contaminate the transmission valve body assembly with foreign matter located at the bottom of the automatic transmission oil pan sub-assembly.

  1. Using a 5 mm socket hexagon wrench, remove the overflow plug and gasket.

  1. Remove the drain plug and gasket.

  1. C318505
    Remove the 10 bolts, automatic transmission oil pan sub-assembly and automatic transmission oil pan gasket.

  1. Remove the 4 transmission oil cleaner magnets from the automatic transmission oil pan sub-assembly.

  1. Examine the particles in the automatic transmission oil pan sub-assembly.

    1. Collect any steel chips with the removed transmission oil cleaner magnets. Carefully inspect the foreign matter and particles in the automatic transmission oil pan sub-assembly and on the transmission oil cleaner magnets to anticipate the type of wear you will find in the automatic transmission assembly.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bush wear


14. REMOVE TRANSMISSION WIRE

  1. C318506E01
    Remove the 2 bolts and 2 temperature sensor clamps, and disconnect the 2 temperature sensors.
    Text in Illustration 
    *1
    Temperature Sensor Clamp
    *2
    Temperature Sensor

  1. Disconnect the 7 solenoid valve connectors and transmission wire from the transmission valve body assembly.

  1. C322258
    Remove the bolt and pull out the transmission wire from the automatic transmission case sub-assembly.

  1. C318508
    Remove the O-ring from the connector of transmission wire.

  1. C181076
    Remove the 2 O-rings from the 2 temperature sensors


15. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C320630
    Remove the 3 bolts and valve body oil strainer assembly from the transmission valve body assembly.

  1. Remove the O-ring from the valve body oil strainer assembly.


16. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. C320631
    Remove the bolt, detent spring cover and detent spring from the transmission valve body assembly.

  1. C320632
    Remove the 12 bolts and transmission valve body assembly from the automatic transmission case sub-assembly.


17. REMOVE TRANSMISSION CASE GASKET

  1. C318514
    Remove the 2 transmission case gaskets from the automatic transmission case sub-assembly.


18. REMOVE BRAKE DRUM GASKET

  1. C321179
    Remove the 2 brake drum gaskets from the automatic transmission case sub-assembly.


19. REMOVE PARKING LOCK PAWL BRACKET

  1. C321180
    Remove the 3 bolts and parking lock pawl bracket from the automatic transmission case sub-assembly.


20. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. C321181
    Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.


21. REMOVE PARKING LOCK PAWL SHAFT

  1. C321182E01
    Pull out the parking lock pawl shaft from the front side, and remove the parking lock pawl and spring.
    Text in Illustration 
    *1
    Parking Lock Pawl
    *2
    E-ring
    *3
    Parking Lock Pawl Shaft
    *4
    Spring

  1. Remove the E-ring from the parking lock pawl shaft.


22. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

  1. C321183E01
    Using a screwdriver and hammer, cut off the spacer and remove it from the manual valve lever shaft.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the manual valve lever shaft.

    HINT:
    Tape the screwdriver tip before use.

  1. C321184
    Using a 3 mm pin punch and hammer, drive out the spring pin.

    HINT:
    Slowly drive out the spring pin so that it does not fall into the automatic transmission case sub-assembly.

  1. Pull the manual valve lever shaft out through the case and remove the manual valve lever sub-assembly.


23. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. C321185E01
    Using a screwdriver, pry out the 2 manual valve lever shaft oil seals from the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


24. REMOVE OIL PUMP ASSEMBLY

  1. C367948
    Remove the 10 bolts.

  1. C367949E01
    Using SST, pull out the oil pump assembly from the automatic transmission case sub-assembly.
    SST
    09610-20012  
    Text in Illustration 
    V113147
    Turn

  1. C321188E01
    Remove the 2 thrust bearing races from the oil pump assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Oil Pump O-ring

  1. Remove the oil pump O-ring from the oil pump assembly.


25. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

  1. C367950E01
    Remove the clutch drum and input shaft assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing

  1. Remove the 3 thrust needle roller bearings from the clutch drum and input shaft assembly.


26. REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. C367951E01
    Remove the direct clutch drum sub-assembly from the input shaft sub-assembly.
    Text in Illustration 
    *1
    Direct Clutch Drum Sub-assembly
    *2
    Input Shaft Sub-assembly


27. INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH)

  1. C321225E01
    Using a dial indicator, measure the clearance of the No. 1 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.75 to 1.05 mm (0.0295 to 0.0413 in.)

    Text in Illustration 
    *1
    Selected Forward Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate forward clutch flange that will bring the clearance within the specified range.

    HINT:
    There are forward clutch flanges of different thicknesses.

    Forward Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35635-71010
    3.0 (0.118)
    35635-71020
    3.1 (0.122)
    35635-71030
    3.2 (0.126)
    35635-71040
    3.3 (0.130)
    35635-71050
    3.4 (0.134)
    35635-71060
    3.5 (0.138)
    35635-71070
    3.6 (0.142)
    35635-71080
    3.7 (0.146)
    35635-71090
    3.8 (0.150)
    35635-71100
    3.9 (0.154)
    35635-71110
    4.0 (0.157)
    35635-71120
    4.1 (0.161)
    35635-71130
    4.2 (0.165)


28. REMOVE CLUTCH DRUM OIL SEAL RING

  1. C367952
    Remove the 3 clutch drum oil seal rings from the input shaft sub-assembly.


29. REMOVE NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
  1. Secure the input shaft sub-assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. C321226E01
    Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the input shaft sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. C321227E01
    Remove the forward clutch flange, 5 No. 1 clutch discs and 5 No. 1 clutch plates from the input shaft sub-assembly.
    Text in Illustration 
    *1
    Forward Clutch Flange
    *2
    No. 1 Clutch Disc
    *3
    No. 1 Clutch Plate


30. INSPECT NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)

  1. C322924
    Check if the contact surfaces of the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 1 clutch disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 1 clutch discs.
    2. Before installing new No. 1 clutch discs, soak them in ATF for at least 15 minutes.


31. REMOVE NO. 1 CLUTCH BALANCER

  1. C321228E01
    Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
    SST
    09387-00110  

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. C321229E01
    Remove the No. 1 clutch balancer and forward clutch return spring sub-assembly from the input shaft sub-assembly.
    Text in Illustration 
    *1
    No. 1 Clutch Balancer
    *2
    Forward Clutch Return Spring Sub-assembly

  1. Remove the O-ring from the No. 1 clutch balancer.


32. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the forward clutch return spring sub-assembly including the spring seat.

    Standard free length:
    26.74 mm (1.053 in.)

    If the free length is more than the standard free length, replace the forward clutch return spring sub-assembly.


33. REMOVE FORWARD CLUTCH PISTON

  1. C321230E01
    While holding the forward clutch piston, apply compressed air to the oil hole of the input shaft sub-assembly to remove the forward clutch piston from the input shaft sub-assembly.
    Text in Illustration 
    *1
    Forward Clutch Piston
    *a
    Oil Hole

  1. Remove the O-ring from the forward clutch piston.

  1. Remove the O-ring from the input shaft sub-assembly.


34. INSPECT INPUT SHAFT SUB-ASSEMBLY

  1. C327918
    Using a caliper gauge, measure the inside diameter of the input shaft sub-assembly bushing.

    Standard inside diameter:
    20.000 to 20.025 mm (0.7874 to 0.7883 in.)

    If the inside diameter is not as specified, replace the input shaft sub-assembly.


35. INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)

  1. C327910E02
    Using a dial indicator, measure the clearance of the No. 2 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.5 to 0.8 mm (0.0197 to 0.0314 in.)

    Text in Illustration 
    *1
    Selected Direct Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate direct clutch flange that will bring the clearance within the specified range.

    HINT:
    There are direct clutch flanges of different thicknesses.

    Direct Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35675-71010
    3.0 (0.118)
    35675-71020
    3.1 (0.122)
    35675-71030
    3.2 (0.126)
    35675-71040
    3.3 (0.130)
    35675-71050
    3.4 (0.134)
    35675-71060
    3.5 (0.138)
    35675-71070
    3.6 (0.142)
    35675-71080
    3.7 (0.146)
    35675-71090
    3.8 (0.150)


36. REMOVE NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

  1. C321219E01
    Using a screwdriver, remove the snap ring from the direct clutch drum sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the direct clutch drum sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. C327906E02
    Remove the direct clutch flange, 5 No. 2 clutch discs and 5 No. 2 clutch plates from the direct clutch drum sub-assembly.
    Text in Illustration 
    *1
    Direct Clutch Flange
    *2
    No. 2 Clutch Disc
    *3
    No. 2 Clutch Plate


37. INSPECT NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

  1. C371117
    Check if the contact surfaces of the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 2 clutch disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 2 clutch discs.
    2. Before installing new No. 2 clutch discs, soak them in ATF for at least 15 minutes.


38. REMOVE NO. 2 CLUTCH BALANCER

  1. C322223E01
    Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
    SST
    09380-60011   (09381-06030, 09381-06040, 09381-06080, 09381-06100, 09381-06110)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. C321222E01
    Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch drum sub-assembly.
    Text in Illustration 
    *1
    No. 2 Clutch Balancer
    *2
    Direct Clutch Return Spring Sub-assembly

  1. Remove the O-ring from the No. 2 clutch balancer.


39. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the direct clutch return spring sub-assembly including the spring seat.

    Standard free length:
    22.14 mm (0.872 in.)

    If the free length is more than the standard free length, replace the direct clutch return spring sub-assembly.


40. REMOVE DIRECT CLUTCH PISTON

  1. C321223E01
    Place the oil pump assembly onto the torque converter assembly, and then place the direct clutch drum sub-assembly onto the oil pump assembly.
    Text in Illustration 
    *1
    Oil Pump Assembly
    *2
    Torque Converter Assembly
    *a
    Oil Hole

  1. While holding the direct clutch piston, apply compressed air to the oil hole of the oil pump assembly to remove the direct clutch piston from the direct clutch drum sub-assembly.

  1. Remove the 2 O-rings from the direct clutch piston.


41. INSPECT DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. C322245
    Using a caliper gauge, measure the inside diameter of the direct clutch drum sub-assembly bushing.

    Standard inside diameter:
    59.515 to 59.540 mm (2.3431 to 2.3440 in.)

    If the inside diameter is not as specified, replace the direct clutch drum sub-assembly.


42. REMOVE MULTIPLE DISC CLUTCH HUB

  1. C321190E01
    Remove the multiple disc clutch hub from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race

  1. Remove the 2 thrust bearing races from the multiple disc clutch hub.


43. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. C321191E01
    Remove the forward clutch hub sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing

  1. Remove the 2 thrust needle roller bearings from the forward clutch hub sub-assembly.


44. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. D028501E01
    Using a caliper gauge, measure the inside diameter of the forward clutch hub sub-assembly bushing.

    Standard inside diameter:
    26.037 to 26.062 mm (1.02508 to 1.02606 in.)

    If the inside diameter is not as specified, replace the forward clutch hub sub-assembly.


45. REMOVE SUN GEAR INPUT DRUM SUB-ASSEMBLY

  1. C321192E01
    Remove the sun gear input drum sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing and thrust bearing race from the sun gear input drum sub-assembly.


46. INSPECT SUN GEAR INPUT DRUM SUB-ASSEMBLY

  1. C322224
    Using a caliper gauge, measure the inside diameter of the sun gear input drum sub-assembly bushing.

    Standard inside diameter:
    35.811 to 35.835 mm (1.4099 to 1.4108 in.)

    If the inside diameter is not as specified, replace the sun gear input drum sub-assembly.


47. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. C321193E01
    Remove the front planetary gear assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race

  1. Remove the 2 thrust bearing races from the front planetary gear assembly


48. INSPECT FRONT PLANETARY GEAR ASSEMBLY

  1. C322225
    Using a caliper gauge, measure the inside diameter of the front planetary gear assembly bushing.

    Standard inside diameter:
    35.811 to 35.835 mm (1.4099 to 1.4108 in.)

    If the inside diameter is not as specified, replace the front planetary gear assembly.


49. REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C321194E01
    Remove the front planetary ring gear with front planetary ring gear flange sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race

  1. Remove the thrust needle roller bearing and thrust bearing race from the front planetary ring gear with front planetary ring gear flange sub-assembly.


50. REMOVE FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C321195E01
    Using needle-nose pliers, remove the snap ring and front planetary ring gear flange sub-assembly from the front planetary ring gear.
    Text in Illustration 
    *1
    Front Planetary Ring Gear
    *2
    Snap Ring
    *3
    Front Planetary Ring Gear Flange Sub-assembly


51. INSPECT FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C322243
    Using a caliper gauge, measure the inside diameter of the front planetary ring gear flange sub-assembly bushing.

    Standard inside diameter:
    54.038 to 54.063 mm (2.1275 to 2.1284 in.)

    If the inside diameter is not as specified, replace the front planetary ring gear flange sub-assembly.


52. INSPECT CLEARANCE OF NO. 2 BRAKE

  1. C321232
    Make sure that the No. 2 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C327912E02
    Using a feeler gauge, measure the No. 2 brake pack clearance between the No. 2 brake disc and No. 2 brake flange.

    Standard clearance:
    0.5 to 0.8 mm (0.0197 to 0.0314 in.)

    Text in Illustration 
    *1
    Selected No. 2 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 2 brake flange that will bring the clearance within the specified range.

    No. 2 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    2.0 (0.0787)
    1
    2.1 (0.0827)
    2
    2.2 (0.0866)
    3
    2.3 (0.0906)
    4
    2.4 (0.0945)
    5
    2.5 (0.0984)
    6
    2.6 (0.102)
    7
    2.7 (0.106)
    8
    2.8 (0.110)


53. REMOVE NO. 2 BRAKE CYLINDER WITH NO.2 BRAKE PISTON

  1. C321201E01
    Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
    SST
    09380-60011   (09381-06010, 09381-06020, 09381-06040, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)
    Text in Illustration 
    *a
    Turn

  1. Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. C321204E01
    Remove the No. 2 brake cylinder with No. 2 brake piston and No. 2 brake piston return spring sub-assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Cylinder with No. 2 Brake Piston
    *2
    No. 2 Brake Piston Return Spring Sub-assembly


54. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the No. 2 brake piston return spring sub-assembly including the spring seat.

    Standard free length:
    16.68 mm (0.657 in.)

    If the free length is more than the standard free length, replace the No. 2 brake piston return spring sub-assembly.


55. REMOVE NO. 2 BRAKE PISTON

  1. C321203
    While holding the No. 2 brake piston, apply compressed air to the oil hole of the No. 2 brake cylinder to remove the No. 2 brake piston from the No. 2 brake cylinder.

  1. Remove the 2 O-rings from the No. 2 brake piston


56. REMOVE NO. 2 BRAKE DISC

  1. C327907E02
    Remove the 2 No. 2 brake flanges, 5 No. 2 brake discs and 4 No. 2 brake plates from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Disc
    *3
    No. 2 Brake Plate


57. INSPECT NO. 2 BRAKE DISC

  1. C322923
    Check if the contact surfaces of the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 2 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 2 brake discs.
    2. Before installing new No. 2 brake discs, soak them in ATF for at least 15 minutes.


58. REMOVE CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR

  1. C321196E01
    Remove the center planetary ring gear flange with center planetary ring gear from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing

  1. Remove the 2 thrust needle roller bearings from the center planetary ring gear flange with center planetary ring gear.


59. REMOVE CENTER PLANETARY RING GEAR

  1. C321197E01
    Using a screwdriver, remove the snap ring from the center planetary ring gear flange with center planetary ring gear.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the center planetary ring gear flange with center planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.

  1. C321198E01
    Remove the center planetary ring gear from the center planetary ring gear flange.
    Text in Illustration 
    *1
    Center Planetary Ring Gear Flange
    *2
    Center Planetary Ring Gear


60. REMOVE CENTER PLANETARY GEAR ASSEMBLY

  1. C321199E01
    Remove the center planetary gear assembly from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race

  1. Remove the thrust bearing race from the center planetary gear assembly.


61. INSPECT CENTER PLANETARY GEAR ASSEMBLY

  1. C321248
    Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.00473 to 0.0267 in.)

    If the clearance is not as specified, replace the center planetary gear assembly.


62. REMOVE PLANETARY SUN GEAR

  1. C321200
    Remove the planetary sun gear from the automatic transmission case sub-assembly.


63. INSPECT CLEARANCE OF NO. 1 BRAKE

  1. C321233
    Make sure that the No. 1 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C327911E02
    Using a feeler gauge, measure the No. 1 brake pack clearance between the No. 1 brake disc and No. 1 brake flange.

    Standard clearance:
    0.4 to 0.7 mm (0.0158 to 0.0275 in.)

    Text in Illustration 
    *1
    Selected No. 1 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 1 brake flange that will bring the clearance within the specified range.

    No. 1 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    4.9 (0.193)
    1
    5.0 (0.197)
    2
    5.1 (0.201)
    3
    5.2 (0.205)
    4
    5.3 (0.209)
    5
    5.4 (0.213)
    6
    5.5 (0.217)
    7
    5.6 (0.220)
    8
    5.7 (0.224)
    A
    5.8 (0.228)


64. REMOVE NO. 1 BRAKE DISC

  1. C322218E01
    Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. C327908E03
    Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Disc
    *3
    No. 1 Brake Plate


65. INSPECT NO. 1 BRAKE DISC

  1. C322922
    Check if the contact surfaces of the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 1 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 1 brake discs.
    2. Before installing new No. 1 brake discs, soak them in ATF for at least 15 minutes.


66. REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

  1. C321202E01
    Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
    SST
    09380-60011   (09381-06010, 09381-06040, 09381-06050, 09381-06070, 09381-06090, 09381-06100, 09381-06110, 09381-06120)
    Text in Illustration 
    *a
    Turn

  1. Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

    NOTICE:
    Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. C322226E01
    Remove the No. 1 brake piston return spring sub-assembly and No. 1 brake cylinder with No. 1 brake piston from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 1 Brake Piston Return Spring Sub-assembly
    *2
    No. 1 Brake Cylinder with No. 1 Brake Piston


67. INSPECT NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C059838E01
    Using a vernier caliper, measure the free length of the No. 1 brake piston return spring sub-assembly including the spring seat.

    Standard free length:
    16.72 mm (0.658 in.)

    If the free length is more than the standard free length, replace the No. 1 brake piston return spring sub-assembly.


68. REMOVE NO. 1 BRAKE PISTON

  1. C321203
    While holding the No. 1 brake piston, apply compressed air to the oil hole of the No. 1 brake cylinder to remove the No. 1 brake piston from the No. 1 brake cylinder.

  1. Remove the 2 O-rings from the No. 1 brake piston


69. INSPECT CLEARANCE OF NO. 4 BRAKE

  1. C322242
    Make sure that the 1st and reverse brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C327913E02
    Using a feeler gauge, measure the No. 4 brake pack clearance between the No. 4 brake disc and No. 4 brake flange.

    Standard clearance:
    0.7 to 1.0 mm (0.0276 to 0.0393 in.)

    Text in Illustration 
    *1
    Selected No. 4 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 4 brake flange that will bring the clearance within the specified range.

    No. 4 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    1.80 (0.0709)
    1
    1.97 (0.0776)
    3
    2.11 (0.0831)
    4
    2.25 (0.0886)
    5
    2.39 (0.0941)
    7
    2.53 (0.0996)
    8
    2.67 (0.105)
    10
    2.81 (0.111)
    11
    2.95 (0.116)
    12
    3.09 (0.122)
    14
    3.23 (0.127)


70. REMOVE INTERMEDIATE SHAFT WITH NO. 3 ONE-WAY CLUTCH ASSEMBLY AND REAR PLANETARY RING GEAR

  1. C321208E01
    Using SST, remove the snap ring from the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07060)

  1. C321209
    Remove the intermediate shaft with No. 3 one-way clutch assembly and rear planetary ring gear from the automatic transmission case sub-assembly.


71. INSPECT NO. 3 ONE-WAY CLUTCH ASSEMBLY

  1. D028532E08
    Hold the rear planetary ring gear and turn the No. 3 one-way clutch assembly.
    Text in Illustration 
    V100135
    Lock
    V100136
    Free

  1. Check that the No. 3 one-way clutch assembly turns freely when turned counterclockwise and locks when turned clockwise.
    If there is a problem with the No. 3 one-way clutch assembly, replace it.


72. REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE

  1. C322254E01
    Remove the No. 3 one-way clutch assembly with one-way clutch inner race from the intermediate shaft with rear planetary ring gear.
    Text in Illustration 
    *1
    No. 3 One-way Clutch Assembly with One-way Clutch Inner Race
    *2
    Intermediate Shaft with Rear Planetary Ring gear


73. REMOVE ONE-WAY CLUTCH INNER RACE

  1. C322253E01
    Remove the one-way clutch inner race from the No. 3 one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Inner Race
    *2
    No. 3 One-way Clutch Assembly


74. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR

  1. C322251E01
    Remove the rear planetary ring gear flange sub-assembly with rear planetary ring gear from the intermediate shaft.
    Text in Illustration 
    *1
    Rear Planetary Ring Gear Flange Sub-assembly with Rear Planetary Ring Gear
    *2
    Thrust Bearing Race

  1. Remove the thrust bearing race from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

  1. C322252E01
    Remove the thrust needle roller bearing and thrust bearing race from the intermediate shaft.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race


75. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. D028531E01
    Using a caliper gauge, measure the inside diameter of the rear planetary ring gear flange sub-assembly bushing.

    Standard inside diameter:
    32.176 to 32.201 mm (1.2668 to 1.2677 in.)

    If the inside diameter is not as specified, replace the rear planetary ring gear flange sub-assembly.


76. REMOVE REAR PLANETARY RING GEAR

  1. C321210E01
    Using a screwdriver, remove the snap ring from the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.

  1. C321211E01
    Remove the rear planetary ring gear from the rear planetary ring gear flange sub-assembly.
    Text in Illustration 
    *1
    Rear Planetary Ring Gear Flange Sub-assembly
    *2
    Rear Planetary Ring Gear


77. REMOVE REAR PLANETARY GEAR ASSEMBLY WITH NO. 4 BRAKE DISC

  1. C322904
    Using a snap ring expander, remove the snap ring from the output shaft of the rear planetary gear assembly.

  1. C321176E01
    Remove the 2 thrust bearing races and thrust needle roller bearing from the output shaft of the rear planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race

  1. C321212E01
    Remove the rear planetary gear assembly with No. 4 brake disc from the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race

  1. Remove the 2 thrust needle roller bearings and 2 thrust bearing races from the rear planetary gear assembly with No. 4 brake disc.

  1. Remove the thrust bearing race from the automatic transmission case sub-assembly.


78. INSPECT REAR PLANETARY GEAR ASSEMBLY

  1. C109349
    Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00788 to 0.0236 in.)

    If the clearance is not as specified, replace the rear planetary gear assembly.

  1. C109350
    Using a caliper gauge, measure the inside diameter of the rear planetary gear bushing.

    Standard inside diameter:
    20.000 to 20.025 mm (0.7874 to 0.7883 in.)

    If the inside diameter is not as specified, replace the rear planetary gear assembly.


79. REMOVE NO. 4 BRAKE DISC

  1. C327909E02
    Remove the No. 4 brake flange, 7 No. 4 brake discs and 6 No. 4 brake plates from the rear planetary gear assembly.
    Text in Illustration 
    *1
    No. 4 Brake Flange
    *2
    No. 4 Brake Disc
    *3
    No. 4 Brake Plate

  1. C321214
    Remove the No. 4 brake flange from the automatic transmission case sub-assembly.


80. INSPECT NO. 4 BRAKE DISC

  1. C322921
    Check if the contact surfaces of the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 4 brake disc is peeled or discolored, or even if part of a groove is damaged, replace all the No. 4 brake discs.
    2. Before installing new No. 4 brake discs, soak them in ATF for at least 15 minutes.


81. REMOVE 1ST AND REVERSE BRAKE PISTON

  1. C321215E01
    Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.
    SST
    09380-60011   (09381-05040, 09381-05050, 09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-06140)

  1. Using SST, remove the snap ring from the automatic transmission case sub-assembly.

    SST
    09350-30020   (09350-07070)

  1. C322246
    Remove the 1st and reverse brake return spring sub-assembly from the automatic transmission case sub-assembly.

  1. C321207
    Apply compressed air to the oil hole of the automatic transmission case sub-assembly to remove the 1st and reverse brake piston from the automatic transmission case sub-assembly.

  1. Remove the O-ring from the 1st and reverse brake piston.


82. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D029830E01
    Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly including the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)

    If the free length is more than the standard free length, replace the 1st and reverse return spring sub-assembly.


83. REMOVE BRAKE REACTION SLEEVE

  1. C321217E01
    Using SST, remove the brake reaction sleeve from the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07080)

  1. Remove the 2 O-rings from the brake reaction sleeve.


84. REMOVE NO. 4 BRAKE PISTON

  1. C321218E01
    Using SST, remove the No. 4 brake piston from the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07090)

  1. Remove the 2 O-rings from the No. 4 brake piston.


85. REMOVE BRAKE PLATE STOPPER SPRING

  1. C321216
    Remove the 2 brake plate stopper springs from the automatic transmission case sub-assembly.

← COMPONENTS (from Jan 2017)INSPECTION (from Jan 2017) →