2014-2019 Hiace · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016


1. BEARING POSITION

C322241E01
Mark
Front Race Diameter
Inside / Outside (mm (in.))
Thrust Bearing Diameter
Inside / Outside (mm (in.))
Rear Race Diameter
Inside / Outside (mm (in.))
A
74.2 (2.921) / 87.74 (3.454)
71.9 (2.831) / 85.6 (3.370)
-
B
40.0 (1.575) / 52.8 (2.079)
34.6 (1.362) / 52.0 (2.047)
-
C
22.0 (0.890) / 44.8 (1.764)
21.3 (0.839) / 41.1 (1.618)
-
D
38.4 (1.512) / 56.5 (2.224)
33.3 (1.311) / 56.6 (2.228)
-
E
-
40.83 (1.607) / 52.8 (2.079)
39.6 (1.559) / 52.8 (2.079)
F
-
37.1 (1.461) / 61.2 (2.409)
44.0 (1.732) / 62.8 (2.472)
G
65.8 (2.591) / 86.3 (3.398)
63.3 (2.492) / 78.8 (3.102)
-
H
66.3 (2.610) / 78.9 (3.106)
63.3 (2.492) / 78.8 (3.102)
-
I
-
55.7 (2.193) / 76.4 (3.008)
53.7 (2.114) / 74.0 (2.913)
J
33.4 (1.315) / 49.0 (1.929)
32.1 (1.264) / 49.35 (1.943)
32.1 (1.264) / 49.0 (1.929)
K
-
21.0 (0.827) / 41.5 (1.634)
23.13 (0.911) / 41.5 (1.634)
L
-
43.55 (1.715) / 61.0 (2.402)
47.1 (1.854) / 67.1 (2.642)
M
36.1 (1.421) / 52.5 (2.067)
37.0 (1.457) / 51.2 (2.016)
36.1 (1.421) / 51.0 (2.008)

2. INSTALL BRAKE PLATE STOPPER SPRING

  1. C321216
    Install the 2 brake plate stopper springs to the automatic transmission case sub-assembly.

    NOTICE:
    The shapes of the parts are different. Refer to the illustration when installing the parts.


3. INSTALL NO. 4 BRAKE PISTON
  1. Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.

  1. Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.

  1. C109328E07
    Install the No. 4 brake piston to the brake reaction sleeve.
    Text in Illustration 
    *1
    No. 4 Brake Piston
    *2
    Brake Reaction Sleeve

    NOTICE:
    Be careful not to damage the O-rings.


4. INSTALL BRAKE REACTION SLEEVE

  1. C322239E01
    With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and No. 4 brake piston to the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Brake Reaction Sleeve
    *2
    No. 4 Brake Piston

    NOTICE:
    Be careful not to damage the O-rings.


5. INSTALL 1ST AND REVERSE BRAKE PISTON

  1. C321231
    Coat a new O-ring with ATF, and install it to the 1st and reverse brake piston.

  1. Install the 1st and reverse brake piston to the automatic transmission case sub-assembly while making sure that the protrusion of the 1st and reverse brake piston is positioned as shown in the illustration.

    NOTICE:
    Be careful not to damage the O-ring.

  1. C322246
    Install the 1st and reverse brake return spring sub-assembly to the automatic transmission case sub-assembly.

  1. Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.

  1. C322240E01
    Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.
    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)
    (09381-06140)
    Text in Illustration 
    *a
    Protective Tape

  1. Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

    NOTICE:
    Be careful not to damage the 1st and reverse brake return spring sub-assembly and automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


6. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. C322238E01
    Coat the thrust bearing race with ATF and install it to the automatic transmission case sub-assembly.

    Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing K
    21.0 (0.827)
    41.5 (1.634)
    Thrust Bearing Race K
    23.13 (0.911)
    41.5 (1.634)
    Thrust Needle Roller Bearing L
    43.55 (1.715)
    61.0 (2.402)
    Thrust Bearing Race L
    47.1 (1.854)
    67.1 (2.642)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing K
    *2
    Thrust Bearing Race K
    *3
    Thrust Needle Roller Bearing L
    *4
    Thrust Bearing Race L

    NOTICE:
    Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

  1. Coat the 2 thrust needle roller bearings and thrust bearing race with ATF and install them to the rear planetary gear assembly.

  1. Install the rear planetary gear assembly to the automatic transmission case sub-assembly.

  1. C322237E01
    Coat the thrust needle roller bearing and 2 thrust bearing races with ATF and install it to the output shaft of the rear planetary gear assembly.
    Bearing and Race Diameter 
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race M
    (Front Race)
    36.1 (1.421)
    52.5 (2.067)
    Thrust Needle Roller Bearing M
    37.0 (1.457)
    51.2 (2.016)
    Thrust Bearing Race M
    (Rear Race)
    36.1 (1.421)
    51.0 (2.008)
    Text in Illustration 
    *1
    Thrust Bearing Race M
    (Front Race)
    *2
    Thrust Needle Roller Bearing M
    *3
    Thrust Bearing Race M
    (Rear Race)

    NOTICE:
    Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

  1. C322904
    Using a snap ring expander, install the snap ring.

  1. C321243E01
    Using a feeler gauge, measure the clearance between the snap ring and thrust bearing race.

    Standard clearance:
    0.02 to 0.12 mm (0.000787 to 0.00472 in.)

    Text in Illustration 
    *1
    Thrust Bearing Race M
    (Rear Race)
    *a
    Mark Area
    If the clearance is outside the standard range, select another thrust bearing race that brings the clearance within the standard range.

    HINT:
    There are 12 different thicknesses for the thrust bearing race.

    Thrust Bearing Race Thickness:
    Part No.
    Mark
    Thickness (mm (in.))
    35789-35060
    C257412
    3.80 (0.150)
    35789-50070
    C257413
    3.85 (0.152)
    35789-35070
    C257414
    3.90 (0.154)
    35789-50080
    C257415
    3.95 (0.156)
    35789-35080
    C257416
    4.00 (0.157)
    35789-50090
    C257417
    4.05 (0.159)
    35789-35090
    C257418
    4.10 (0.161)
    35789-50100
    C257419
    4.15 (0.163)
    35789-35100
    C257420
    4.20 (0.165)
    35789-50110
    C257421
    4.25 (0.167)
    35789-50120
    C257422
    4.30 (0.169)
    35789-50130
    C257423
    4.35 (0.171)


7. INSTALL NO. 4 BRAKE DISC

  1. C322236E01
    Install the 2 No. 4 brake flanges, 5 No. 4 brake discs and 4 No. 4 brake plates to the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 4 Brake Flange
    *2
    No. 4 Brake Disc
    *3
    No. 4 Brake Plate

    NOTICE:
    1. Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.
    2. Install the thicker No. 4 brake flange first, and then install the thinner one.


8. INSTALL INTERMEDIATE SHAFT

  1. C322215E01
    Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the intermediate shaft.

    Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing J
    32.1 (1.264)
    49.35 (1.943)
    Thrust Bearing Race J
    (Rear Race)
    32.1 (1.264)
    49.0 (1.929)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing J
    *2
    Thrust Bearing Race J

  1. Install the intermediate shaft to the automatic transmission case sub-assembly.


9. INSTALL REAR PLANETARY RING GEAR

  1. C321211E01
    Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.
    Text in Illustration 
    *1
    Rear Planetary Ring Gear Flange Sub-assembly
    *2
    Rear Planetary Ring Gear

  1. C321210E01
    Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.


10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR

  1. C322235E01
    Coat the thrust bearing race with ATF and install it to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

    Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race J
    (Front Race)
    33.4 (1.315.)
    49.0 (1.929)

    Text in Illustration 
    *1
    Thrust Bearing Race J

    NOTICE:
    Be sure to install the thrust bearing race in the correct direction.

  1. Install the rear planetary ring gear flange sub-assembly with rear planetary ring gear to the automatic transmission case sub-assembly.


11. INSTALL ONE-WAY CLUTCH INNER RACE

  1. C322253E01
    Install the one-way clutch inner race to the No. 3 one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Inner Race
    *2
    No. 3 One-way Clutch Assembly

    HINT:
    Rotate the one-way clutch inner race clockwise to install it.


12. INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE

  1. C322217
    Install the No. 3 one-way clutch assembly with one-way clutch inner race to the automatic transmission case sub-assembly.

  1. C322917E01
    Using SST, install the snap ring to the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07060)
    Text in Illustration 
    *1
    Snap Ring
    *a
    19°
    *b
    49°
    V100135
    Front Side

    NOTICE:
    1. Install the snap ring so that the tapered side is facing out.
    2. Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.


13. INSPECT CLEARANCE OF NO. 4 BRAKE

  1. C322242
    Make sure that the 1st and reverse brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321236E01
    Using a feeler gauge, measure the No. 4 brake pack clearance between the No. 4 brake disc and No. 4 brake flange.

    Standard clearance:
    0.5 to 0.8 mm (0.0197 to 0.0314 in.)

    Text in Illustration 
    *1
    Selected No. 4 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 4 brake flange that will bring the clearance within the specified range.

    No. 4 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    1.80 (0.0709)
    1
    1.97 (0.0776)
    3
    2.11 (0.0831)
    4
    2.25 (0.0886)
    5
    2.39 (0.0941)
    7
    2.53 (0.0996)
    8
    2.67 (0.105)
    10
    2.81 (0.111)
    11
    2.95 (0.116)
    12
    3.09 (0.122)
    14
    3.23 (0.127)


14. INSTALL NO. 1 BRAKE PISTON
  1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

  1. C322214
    With the No. 1 brake piston return spring sub-assembly installed to the No. 1 brake piston, align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston to the No. 1 brake cylinder.


15. INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

  1. C322221
    Install the No. 1 brake cylinder with No. 1 brake piston to the automatic transmission case sub-assembly while making sure that the 2 claws of the No. 1 brake cylinder with No. 1 brake piston are positioned as shown in the illustration.


16. INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C322219
    Align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston return spring sub-assembly to the No. 1 brake piston.

  1. C321202E01
    Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
    SST
    09380-60010   (09381-06010, 09381-06040, 09381-06050, 09381-06070, 09381-06090, 09381-06100, 09381-06110, 09381-06120)
    Text in Illustration 
    *a
    Turn

  1. C322919E01
    Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    22.5°
    *b
    37.5°

    NOTICE:
    1. Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
    2. Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


17. INSTALL NO. 1 BRAKE DISC

  1. C321206E01
    Install the No. 1 brake flange, 3 No. 1 brake discs and 3 No. 1 brake plates to the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Disc
    *3
    No. 1 Brake Plate

    NOTICE:
    Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.

  1. C322918E01
    Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    22.5°
    *b
    37.5°

    NOTICE:
    1. Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
    2. Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


18. INSPECT CLEARANCE OF NO. 1 BRAKE

  1. C321233
    Make sure that the No. 1 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321235E01
    Using a feeler gauge, measure the No. 1 brake pack clearance between the No. 1 brake disc and No. 1 brake flange.

    Standard clearance:
    0.3 to 0.6 mm (0.0119 to 0.0236 in.)

    Text in Illustration 
    *1
    Selected No. 1 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 1 brake flange that will bring the clearance within the specified range.

    No. 1 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    4.9 (0.193)
    1
    5.0 (0.197)
    2
    5.1 (0.201)
    3
    5.2 (0.205)
    4
    5.3 (0.209)
    5
    5.4 (0.213)
    6
    5.5 (0.217)
    7
    5.6 (0.220)
    8
    5.7 (0.224)
    A
    5.8 (0.228)


19. INSTALL PLANETARY SUN GEAR

  1. C321200
    Install the planetary sun gear to the automatic transmission case sub-assembly.


20. INSTALL CENTER PLANETARY GEAR ASSEMBLY

  1. C322234E01
    Coat the thrust bearing race with ATF and install it to the center planetary gear assembly.

    Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race I
    53.7 (2.114)
    74.0 (2.913)

    Text in Illustration 
    *1
    Thrust Bearing Race I

  1. Install the center planetary gear assembly to the automatic transmission case sub-assembly.


21. INSTALL CENTER PLANETARY RING GEAR

  1. C321198E01
    Install the center planetary ring gear to the center planetary ring gear flange
    Text in Illustration 
    *1
    Center Planetary Ring Gear Flange
    *2
    Center Planetary Ring Gear

  1. C321197E01
    Using a screwdriver, install the snap ring to the center planetary ring gear flange with center planetary ring gear.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the center planetary ring gear flange with center planetary ring gear.

    HINT:
    Tape the screwdriver tip before use.


22. INSTALL CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR

  1. C322233E01
    Coat the 2 thrust needle roller bearings with ATF and install them to the center planetary ring gear flange with center planetary ring gear.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing H
    63.3 (2.492)
    78.8 (3.102)
    Thrust Needle Roller Bearing I
    55.7 (2.193)
    76.4 (3.008)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing H
    *2
    Thrust Needle Roller Bearing I

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.

  1. Install the center planetary ring gear flange with center planetary ring gear to the automatic transmission case sub-assembly.


23. INSTALL NO. 2 BRAKE DISC

  1. C321205E01
    Install the 2 No. 2 brake flanges, 4 No. 2 brake discs and 3 No. 2 brake plates to the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Disc
    *3
    No. 2 Brake Plate

    NOTICE:
    Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.


24. INSTALL NO. 2 BRAKE PISTON
  1. Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

  1. C322213
    With the No. 2 brake piston return spring sub-assembly installed to the No. 2 brake piston, align the claw of the No. 2 brake piston return spring sub-assembly with the claw of the No. 2 brake cylinder, and then install the No. 2 brake piston to the No. 2 brake cylinder.

    NOTICE:
    Be careful not to damage the O-rings.


25. INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

  1. C322220
    Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly while making sure that the claw of the No. 2 brake piston return spring sub-assembly is positioned as shown in the illustration.

  1. C322222
    Install the No. 2 brake cylinder with No. 2 brake piston to the automatic transmission case sub-assembly while making sure that the claw of the No. 1 brake cylinder with No. 1 brake piston is positioned as shown in the illustration.

  1. C321201E01
    Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06040, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)
    Text in Illustration 
    *a
    Turn

  1. C322920E01
    Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
    Text in Illustration 
    *a
    30°

    NOTICE:
    1. Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
    2. Be careful not to damage the automatic transmission case sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


26. INSPECT CLEARANCE OF NO. 2 BRAKE

  1. C321232
    Make sure that the No. 2 brake piston moves smoothly when applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

  1. C321234E01
    Using a feeler gauge, measure the No. 2 brake pack clearance between the No. 2 brake disc and No. 2 brake flange.

    Standard clearance:
    0.4 to 0.7 mm (0.0158 to 0.0275 in.)

    Text in Illustration 
    *1
    Selected No. 2 Brake Flange
    If the clearance is not as specified, select and install an appropriate No. 2 brake flange that will bring the clearance within the specified range.

    No. 2 Brake Flange Thickness:
    Mark
    Thickness (mm (in.))
    0
    2.0 (0.0787)
    1
    2.1 (0.0827)
    2
    2.2 (0.0866)
    3
    2.3 (0.0906)
    4
    2.4 (0.0945)
    5
    2.5 (0.0984)
    6
    2.6 (0.102)
    7
    2.7 (0.106)
    8
    2.8 (0.110)


27. INSTALL FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C321195E01
    Set the snap ring onto the front planetary ring gear flange sub-assembly. Using needle-nose pliers, insert the snap ring into the front planetary ring gear while squeezing it, and then expand the snap ring to install it.
    Text in Illustration 
    *1
    Front Planetary Ring Gear
    *2
    Snap Ring
    *3
    Front Planetary Ring Gear Flange Sub-assembly

    NOTICE:
    Make sure the snap ring is securely inserted into the groove of the front planetary ring gear.


28. INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. C322232E01
    Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the front planetary ring gear with front planetary ring gear flange sub-assembly.

    Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing G
    63.3 (2.492)
    78.8 (3.102)
    Thrust Bearing Race H
    66.3 (2.610)
    78.9 (3.106)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing G
    *2
    Thrust Bearing Race H

    NOTICE:
    Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

  1. Install the front planetary ring gear with front planetary ring gear flange sub-assembly to the automatic transmission case sub-assembly.


29. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. C322231E01
    Coat the 2 thrust bearing races with ATF and install them to the front planetary gear assembly.

    Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race F
    44.0 (1.732)
    62.8 (2.472)
    Thrust Bearing Race G
    65.8 (2.591)
    86.3 (3.398)

    Text in Illustration 
    *1
    Thrust Bearing Race F
    *2
    Thrust Bearing Race G

    NOTICE:
    Be sure to install the thrust bearing race in the correct direction.

  1. Install the front planetary gear assembly to the automatic transmission case sub-assembly.


30. INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY

  1. C322230E01
    Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the sun gear input drum sub-assembly.

    Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race E
    40.83 (1.607)
    52.8 (2.079)
    Thrust Needle Roller Bearing F
    37.1 (1.461)
    61.2 (2.409)

    Text in Illustration 
    *1
    Thrust Bearing Race E
    *2
    Thrust Needle Roller Bearing F

    NOTICE:
    Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

  1. Install the sun gear input drum sub-assembly to the automatic transmission case sub-assembly.


31. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. C322229E01
    Coat the 2 thrust needle roller bearings with ATF and install them to the forward clutch hub sub-assembly.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing D
    33.3 (1.311)
    56.6 (2.228)
    Thrust Needle Roller Bearing E
    39.6 (1.559)
    52.8 (2.079)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing D
    *2
    Thrust Needle Roller Bearing E

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.

  1. Install the forward clutch hub sub-assembly to the automatic transmission case sub-assembly.


32. INSTALL MULTIPLE DISC CLUTCH HUB

  1. C322228E01
    Coat the 2 thrust bearing races with ATF and install them to the multiple disc clutch hub.

    Thrust Bearing Race Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust bearing race C
    22.6 (0.890)
    44.8 (1.764)
    Thrust bearing race D
    38.4 (1.512)
    56.5 (2.224)

    Text in Illustration 
    *1
    Thrust bearing race C
    *2
    Thrust bearing race D

    NOTICE:
    Be sure to install the thrust bearing race in the correct direction.

  1. Install the multiple disc clutch hub to the automatic transmission case sub-assembly.


33. INSTALL DIRECT CLUTCH PISTON
  1. Coat 2 new O-rings with ATF, and install them to the direct clutch piston.

  1. C322898
    Install the direct clutch piston to the direct clutch drum sub-assembly.

    NOTICE:
    Be careful not to damage the O-rings.


34. INSTALL NO. 2 CLUTCH BALANCER

  1. C321222E01
    Install the direct clutch return spring sub-assembly to the direct clutch piston.
    Text in Illustration 
    *1
    No. 2 Clutch Balancer
    *2
    Direct Clutch Return Spring Sub-assembly

  1. Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.

  1. Install the No. 2 clutch balancer to the direct clutch drum sub-assembly.

    NOTICE:
    Be careful not to damage the O-ring.

  1. C322223E01
    Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080, 09381-06100, 09381-06110)

    NOTICE:
    Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Do not expand the snap ring excessively.


35. INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)

  1. C321220E01
    Install the 4 No. 2 clutch plates, 4 No. 2 clutch discs and direct clutch flange to the direct clutch drum sub-assembly.
    Text in Illustration 
    *1
    Direct Clutch Flange
    *2
    No. 2 Clutch Disc
    *3
    No. 2 Clutch Plate

    NOTICE:
    Make sure that the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are installed in the correct order.

  1. C321219E01
    Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the direct clutch drum sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


36. INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)

  1. C321224E01
    Using a dial indicator, measure the clearance of the No. 2 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.4 to 0.7 mm (0.0157 to 0.0275 in.)

    Text in Illustration 
    *1
    Selected Direct Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate direct clutch flange that will bring the clearance within the specified range.

    HINT:
    There are direct clutch flanges of different thicknesses.

    Direct Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35675-71010
    3.0 (0.118)
    35675-71020
    3.1 (0.122)
    35675-71030
    3.2 (0.126)
    35675-71040
    3.3 (0.130)
    35675-71050
    3.4 (0.134)
    35675-71060
    3.5 (0.138)
    35675-71070
    3.6 (0.142)
    35675-71080
    3.7 (0.146)
    35675-71090
    3.8 (0.150)


37. INSTALL FORWARD CLUTCH PISTON
  1. Coat a new O-ring with ATF, and install it to the input shaft sub-assembly.

  1. Coat a new O-ring with ATF, and install it to the forward clutch piston.

  1. C322899
    Install the forward clutch piston to the input shaft sub-assembly.

    NOTICE:
    Be careful not to damage the O-rings.


38. INSTALL NO. 1 CLUTCH BALANCER
  1. Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.

  1. C321229E01
    Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the input shaft sub-assembly.
    Text in Illustration 
    *1
    No. 1 Clutch Balancer
    *2
    Forward Clutch Return Spring Sub-assembly

    NOTICE:
    Be careful not to damage the O-ring.

  1. C321228E01
    Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
    SST
    09387-00110  

    NOTICE:
    Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Do not expand the snap ring excessively.


39. INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)

  1. C321227E01
    Install the 5 No. 1 clutch plates, 5 No. 1 clutch discs and forward clutch flange to the input shaft sub-assembly.
    Text in Illustration 
    *1
    Forward Clutch Flange
    *2
    No. 1 Clutch Disc
    *3
    No. 1 Clutch Plate

    NOTICE:
    Make sure that the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are installed in the correct order.

  1. C321226E01
    Using a screwdriver, install the snap ring.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Be careful not to damage the input shaft sub-assembly.

    HINT:
    Tape the screwdriver tip before use.


40. INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH DISC)

  1. C321225E01
    Using a dial indicator, measure the clearance of the No. 1 clutch at several points while applying compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) to the oil hole as shown in the illustration, and calculate the average.

    Standard clearance:
    0.75 to 1.05 mm (0.0295 to 0.0413 in.)

    Text in Illustration 
    *1
    Selected Forward Clutch Flange
    *a
    Oil Hole
    If the clearance is not as specified, select and install an appropriate forward clutch flange that will bring the clearance within the specified range.

    HINT:
    There are forward clutch flanges of different thicknesses.

    Forward Clutch Flange Thickness:
    Part No.
    Thickness (mm (in.))
    35635-71010
    3.0 (0.118)
    35635-71020
    3.1 (0.122)
    35635-71030
    3.2 (0.126)
    35635-71040
    3.3 (0.130)
    35635-71050
    3.4 (0.134)
    35635-71060
    3.5 (0.138)
    35635-71070
    3.6 (0.142)
    35635-71080
    3.7 (0.146)
    35635-71090
    3.8 (0.150)
    35635-71100
    3.9 (0.154)
    35635-71110
    4.0 (0.157)
    35635-71120
    4.1 (0.161)
    35635-71130
    4.2 (0.165)


41. INSTALL CLUTCH DRUM OIL SEAL RING

  1. C322249
    Coat 3 new clutch drum oil seal rings with ATF and install them to the input shaft sub-assembly.

    NOTICE:
    Do not expand the clutch drum oil seal ring ends excessively.

    HINT:
    After installing the clutch drum oil seal rings, check that they rotate smoothly.


42. INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. C322250E01
    Install the direct clutch drum sub-assembly to the input shaft sub-assembly.
    Text in Illustration 
    *1
    Direct Clutch Drum Sub-assembly
    *2
    Input Shaft Sub-assembly


43. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

  1. C322227E01
    Coat the 3 thrust needle roller bearings with ATF and install them to the clutch drum and input shaft assembly.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Needle Roller Bearing A
    71.9 (2.831)
    85.6 (3.370)
    Thrust Needle Roller Bearing B
    34.6 (1.362)
    52.0 (2.047)
    Thrust Needle Roller Bearing C
    21.3 (0.839)
    41.1 (1.618)

    Text in Illustration 
    *1
    Thrust Needle Roller Bearing A
    *2
    Thrust Needle Roller Bearing B
    *3
    Thrust Needle Roller Bearing C

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.

  1. Install the clutch drum and input shaft assembly to the automatic transmission case sub-assembly.


44. INSTALL OIL PUMP ASSEMBLY

  1. C322900E01
    Coat the 2 thrust bearing races with ATF and install them to the oil pump assembly.
    Race Diameter 
    Item
    Inside (mm (in.))
    Outside (mm (in.))
    Thrust Bearing Race B
    40.0 (1.575)
    52.8 (2.079)
    Thrust Bearing Race A
    74.2 (2.921)
    87.74 (3.454)
    Text in Illustration 
    *1
    Thrust Bearing Race B
    *2
    Thrust Bearing Race A
    *3
    Oil Pump O-ring

    NOTICE:
    Be sure to install the thrust bearing race in the correct direction.

  1. Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.

  1. Set the oil pump assembly on the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.

    NOTICE:
    Be careful not to damage the oil pump O-ring.

  1. Temporarily install the oil pump assembly to the automatic transmission case sub-assembly.

  1. C321186
    Install the oil pump assembly with the 10 bolts.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }


45. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. C321239E01
    Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.
    SST
    09350-30020   (09350-07110)

    Standard depth:
    -0.5 to 0.5 mm (-0.0196 to 0.0196 in.)

  1. Coat the lip of the manual valve lever shaft oil seal with MP grease.


46. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. C321240E01
    Install a new spacer to the manual valve lever sub-assembly.
    Text in Illustration 
    *1
    Manual Valve Lever Sub-assembly
    *2
    Spacer

  1. Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.

  1. C321241
    Using a hammer, drive in a new spring pin.

  1. Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.

  1. C321184
    Using a 3 mm pin punch and a hammer, stake the spacer.

  1. Check that the spacer does not turn.

  1. Make sure that the shaft rotates smoothly.


47. INSTALL PARKING LOCK PAWL SHAFT
  1. Install the E-ring to the parking lock pawl shaft.

  1. C321182E01
    Install the parking lock pawl, parking lock pawl shaft and spring to the automatic transmission case sub-assembly.
    Text in Illustration 
    *1
    Parking Lock Pawl
    *2
    E-ring
    *3
    Parking Lock Pawl Shaft
    *4
    Spring


48. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. C321181
    Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


49. INSTALL PARKING LOCK PAWL BRACKET

  1. C321180
    Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Move the manual valve lever sub-assembly to P, and check the output shaft is locked by the parking lock pawl.


50. INSTALL BRAKE DRUM GASKET

  1. C321179
    Install 2 new brake drum gaskets to the automatic transmission case sub-assembly.


51. INSTALL TRANSMISSION CASE GASKET

  1. C318514
    Install 2 new transmission case gaskets to the automatic transmission case sub-assembly.


52. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C322901E01
    Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    Text in Illustration 
    *1
    Manual Valve Lever Sub-assembly
    *2
    Manual Valve

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    Bolt A:
    25 mm (0.984 in.)
    Bolt B:
    36 mm (1.42 in.)
    Bolt C:
    50 mm (1.97 in.)

  1. C320631
    Install the detent spring and detent spring cover to the transmission valve body assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


53. INSTALL VALVE BODY OIL STRAINER ASSEMBLY
  1. Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.

  1. C320630
    Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


54. INSTALL TRANSMISSION WIRE

  1. C181076
    Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.

  1. C318508
    Coat a new O-ring with ATF, and install it to the transmission wire.

  1. C322258
    Install the transmission wire to the automatic transmission case sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C318506E02
    Connect the 7 solenoid valve connectors.
    Text in Illustration 
    *1
    Temperature Sensor Clamp
    *2
    Temperature Sensor

  1. Install the 2 temperature sensors and 2 temperature sensor clamps to the transmission valve body assembly with the bolt.

    Torque:
    for Bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for Bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


55. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

  1. C318509E01
    Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.

  1. Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.

  1. C318505
    C157303E06
    Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

    Text in Illustration 
    *1
    Sleeve
    *2
    Automatic Transmission Case Sub-assembly
    *a
    Correct
    *b
    Incorrect
    *c
    Protrusion

    NOTICE:
    1. Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.
    2. Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.
    3. Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.
    4. When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.

  1. Install the drain plug and a new gasket to the automatic transmission oil pan sub-assembly.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Using a 5 mm hexagon socket wrench, install a new gasket and overflow plug to the automatic transmission oil pan sub-assembly.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


56. INSTALL AUTOMATIC TRANSMISSION HOUSING
  1. Clean and degrease the bolts and bolt holes with non-residue solvent.

  1. C322902
    Install the automatic transmission housing to the automatic transmission case sub-assembly with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

  1. Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C322903E01
    Install 4 bolts to the automatic transmission housing.

    Torque:
    for Bolt A (M10 bolt):
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for Bolt B (M12 bolt):
    57 N*m{ 579 kgf*cm , 42 ft.*lbf }


57. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. C321244E01
    Using SST and a hammer, drive in the automatic transmission extension housing oil seal to the extension housing sub-assembly.
    SST
    09309-37010  

    Standard depth:
    5.4 to 5.8 mm (0.213 to 0.228 in.)

  1. Coat the lip of a new automatic transmission extension housing oil seal with MP grease.


58. INSTALL EXTENSION HOUSING DUST DEFLECTOR

  1. C321245E01
    Using SST and a press, install a new extension housing dust deflector to the extension housing sub-assembly.
    SST
    09950-60020   (09951-01030)


59. INSTALL EXTENSION HOUSING SUB-ASSEMBLY
  1. Clean and degrease the threads of the 8 bolts, bolt holes and the contact surfaces of the automatic transmission case sub-assembly and extension housing sub-assembly with non-residue solvent.

  1. C321246E01
    Apply seal packing to the extension housing sub-assembly as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *a
    Seal Packing

    NOTICE:
    1. Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.
    2. After applying seal packing, install the extension housing sub-assembly to the automatic transmission case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.

  1. Apply adhesive to 2 or 3 threads on the end of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C321173E01
    Install the extension housing sub-assembly to the automatic transmission case sub-assembly with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.

    Bolt length:
    for Bolt A:
    40 mm (1.57 in.)
    for Bolt B:
    45 mm (1.77 in.)


60. INSTALL OIL COOLER TUBE UNION
  1. Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.

  1. C321247E01
    Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.
    SST
    09268-78010  

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length
    *b
    18° to 22°
    *c
    -2° to 2°

    HINT:
    1. Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
      (Click here)
    2. When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 25 N*m (252 kgf*cm, 18 ft.*lbf)


61. INSTALL AUTOMATIC TRANSMISSION CASE PLUG
  1. Coat 6 new O-rings with ATF, and install them to the 6 automatic transmission case plugs.

  1. C321170
    Install the 6 automatic transmission case plugs to the automatic transmission case sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. Coat a new O-ring with ATF, and install it to the automatic transmission case plug.

  1. C321171
    Using a T55 "TORX" socket wrench, install the automatic transmission case plug to the automatic transmission case sub-assembly.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


62. INSTALL REFILL PLUG
  1. Coat a new O-ring with ATF, and install it to the refill plug.

  1. C320629
    Install the refill plug to the extension housing sub-assembly.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


63. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.

  1. Clean the bolt and bolt hole.

  1. Apply adhesive to 2 or 3 threads on the end of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the bolt within 3 minutes of applying adhesive.

  1. C320637
    Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.

  1. Install a lock washer and nut to the park/neutral position switch assembly.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.

  1. C320628E01
    Turn the transmission control shaft lever clockwise until it stops, and then return the transmission control shaft lever counterclockwise 2 notches to N.

  1. D025795E28
    Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

    Text in Illustration 
    *a
    Neutral Basic Line
    *b
    Groove

  1. Using a screwdriver, bend the tabs of the lock washer.

    NOTICE:
    1. Be careful not to damage the park/neutral position switch assembly.
    2. Bend at least 2 of the lock washer tabs.

    HINT:
    Tape the screwdriver tip before use.


64. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

  1. C320636E01
    Install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }


65. INSTALL TRANSMISSION REVOLUTION SENSOR

  1. C318500
    Coat a new O-ring with ATF, and install it to the transmission revolution sensor NT.

  1. Install the transmission revolution sensor NT to the automatic transmission case sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C318501
    Coat a new O-ring with ATF, and install it to the transmission revolution sensor SP2.

  1. Install the transmission revolution sensor SP2 to the automatic transmission case sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


66. INSTALL BREATHER PLUG HOSE

  1. C320613E01
    Install the breather plug sub-assembly, clamp and breather plug to the breather plug hose.
    Text in Illustration 
    *1
    Breather Plug Sub-assembly
    *2
    Clamp
    *3
    Breather Plug Hose
    *4
    Breather Plug
    *5
    O-ring

  1. Coat a new O-ring with ATF, and install it to the breather plug.

  1. C320611
    Install the breather plug hose to the automatic transmission case sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Be careful not to damage the O-rings.

← INSPECTION (Jan 2015 – Dec 2016)REASSEMBLY (Apr 2016 – Dec 2016) →