2014-2019 Hiace · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Oct 2014


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the air fuel ratio was lean or rich, as well as the other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.


  1. A103809E49
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an GTS, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets from before the DTC was stored
    2. 1 data set from when the DTC was stored
    3. 1 data set from after the DTC was stored
    1. These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

PENDING FREEZE FRAME DATA

HINT:
Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch ON.

  3. Turn the GTS on.

  4. Enter the following menus: Engine and ECT / Trouble Codes.

  5. Select a DTC in order to display its pending freeze frame data.

    HINT:
    1. Pending freeze frame data is cleared when any of the following occurs.
      1. Using the GTS, the DTCs are cleared.
      2. The cable is disconnected from the negative (-) auxiliary battery terminal.
      3. 40 trips with the engine fully warmed up have been performed after returning to normal.
        (Pending freeze frame data will not be cleared by only returning the system to normal.)
    2. With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.

A251781E30
A251782E32

LIST OF FREEZE FRAME DATA
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
The speed indicated on the speedometer.
Target Idle Engine Speed
Target idling speed
-
Engine Speed
Engine speed
-
Calculate Load
Calculated load
The load calculated by the ECM.
MAF
Mass air flow volume
If approximately 0.0 gm/sec:
  1. The mass air flow meter power source circuit is open or shorted.
  2. The VG circuit is open or shorted.
  3. The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure
-
MAP
Absolute pressure inside intake manifold
-
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature
If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air Temp (Turbo) Supported
Intake air temp (turbo) Supported
-
Intake Air Temp (Turbo)
Intake air temperature after intercooler
If -40°C (-40°F), the sensor circuit is open.
If 190°C (374°F) or higher, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Radiator Coolant Temp
Engine coolant temperature (radiator side)
If -40°C (-40°F), the sensor circuit is open.
If 190°C (374°F) or higher, the sensor circuit is shorted
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Alternate Duty Ratio
Alternate duty ratio
-
Glow Control Unit Duty
Glow control unit duty
-
Glow Indicator Supported
Glow indicator supported
-
Glow Indicator
Glow indicator
-
Eng Oil Press Switch Valve
Engine oil pressure switching valve status
-
Engine Oil Pressure
Engine oil pressure
-
Accel Position
Accelerator pedal position sensor
-
Accel Sens. No.1 Volt %
No. 1 Accelerator pedal position
-
Accel Sens. No.2 Volt %
No. 2 Accelerator pedal position
-
Target Throttle Position Supported
Target throttle position supported
-
Target Throttle Position
Target throttle position
-
Target Throttle Position #2 Supported
Target throttle position (bank 2) supported
-
Target Throttle Position #2
Target throttle position (bank 2)
-
Actual Throttle Position Supported
Actual throttle position supported
-
Actual Throttle Position
Actual throttle position
-
Actual Throttle Position #2 Supported
Actual throttle position (bank 2) Supported
-
Actual Throttle Position #2
Actual throttle position (bank 2)
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Close Learning Val.
Throttle fully closed position learned value
-
Throttle Sensor Volt %
Throttle position sensor output voltage
-
Injection Volume
Injection volume
-
Inj. FB Vol. for Idle
Injection feedback value for idle speed control
-
Inj Vol Feedback Learning
Injection volume feedback learned value
-
Idle Signal Output Value
Idle signal output value
-
Injection Feedback Val #1
Injection volume correction for cylinder 1
-
Injection Feedback Val #2
Injection volume correction for cylinder 2
-
Injection Feedback Val #3
Injection volume correction for cylinder 3
-
Injection Feedback Val #4
Injection volume correction for cylinder 4
-
Pilot 1 Injection Period
Pilot 1 injection period
-
Pilot 2 Injection Period
Pilot 2 injection period
-
Main Injection Period
Main injection period
-
After Injection Period
Post injection period
-
Pilot 1 Injection Timing
Pilot 1 injection timing
-
Pilot 2 Injection Timing
Pilot 2 injection timing
-
Main Injection Timing
Main injection timing
-
After Injection Timing
Post injection timing
-
Pilot Quantity Learning
Pilot quantity learning status
The status is only displayed while performing "Pilot Quantity Learning".
Injector Pilot Quantity Learning
Pilot quantity learning status
-
Actuator Pilot Quantity Learning
Actuator pilot quantity learning status
-
Temperature Pilot Quantity Learning
Temperature pilot quantity learning status
-
Catalyst Pilot Quantity Learning
Catalyst pilot quantity learning status
-
Injection Pressure Correction
Injection pressure feedback compensation volume
-
Injection EDU Relay Request
Status of the EDU relay request
-
Target Common Rail Pressure Supported
Target common rail pressure supported
-
Target Common Rail Pressure
Target common rail pressure
-
Common Rail Pressure Supported
Target common rail pressure supported
-
Common Rail Pressure
Fuel pressure
-
Fuel Temperature Supported
Fuel temperature supported
-
Fuel Temperature
Fuel temperature
-
Target Pump SCV Current
Final pump current target value
-
Pump SCV Learning Value
Pump current learned value
-
Pump SCV Status
Pump SCV status
-
Pump SCV Duty Request
Pump SCV duty request
-
Pressure Discharge Valve
Pressure discharge valve operation prohibition
-
AF Lambda B1S1
Lambda equivalent ratio
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage
-
AFS Current B1S1
Air fuel ratio sensor output current
-
Target EGR Valve Pos Supported
Target EGR valve position supported
-
Target EGR Valve Pos
Target EGR valve position
-
Target EGR Valve Pos #2 Supported
Target EGR valve position (bank 2) supported
-
Target EGR Valve Pos #2
Target EGR valve position (bank 2)
-
Actual EGR Valve Pos Supported
Actual EGR valve position supported
-
Actual EGR Valve Pos.
Actual EGR valve position
-
Actual EGR Valve Pos #2 Supported
Actual EGR valve position (bank 2) supported
-
Actual EGR Valve Pos #2
Actual EGR valve position (bank 2)
-
EGR Position Sensor
EGR position sensor
-
EGR Motor Duty #1
EGR motor duty ratio
-
EGR Close Lrn. Val.
EGR valve fully closed position learned value
-
EGR Cooler Bypass VSV
Vacuum switching valve (for EGR bypass valve) status
-
EGR Cooler Bypass Position
EGR cooler bypass position
-
EGR Cut VSV
Vacuum switching valve (for EGR cut valve) status
-
Target Booster Pressure Supported
Target booster pressure supported
-
Target Booster Pressure
Target booster pressure
-
VN Turbo Command Supported
VN turbo command supported
-
Target VN Turbo Position
Target VN turbo position
-
VN Turbo Command #2 Supported
VN turbo command (bank 2) supported
-
Target VN Turbo Position #2
Target VN Turbo Position (bank 2)
-
Actual VN Position Supported
Actual VN turbo position supported
-
Actual VN Turbo Position
Actual VN turbo position
-
Actual VN Position #2 Supported
Actual VN turbo position (bank 2) supported
-
Actual VN Turbo Position #2
Actual VN turbo position (bank 2)
-
VN Position Sensor Out
VN position sensor output voltage
-
VN Motor Duty
VN turbo motor duty
-
VN Close Learn Value
VN turbo fully closed position learned value
-
VN Turbo Max Angle
VN turbo maximum opening amount
-
VN Turbo Min Angle
VN turbo minimum opening amount
-
Exhaust Temperature B1S1 Supported
Status of the exhaust temperature B1S1 supported
-
Exhaust Temperature B1S1
Exhaust temperature sensor (B1S1)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S2 Supported
Status of the exhaust temperature B1S2 supported
-
Exhaust Temperature B1S2
No. 2 exhaust temperature sensor (B1S2)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S3 Supported
Status of the exhaust temperature B1S3 supported
-
Exhaust Temperature B1S3
No. 3 exhaust temperature sensor (B1S3)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
DPF Differential Pressure Supported
DPF differential pressure supported
-
DPF Differential Pressure
DPF differential pressure
-
Catalyst Differential Press
Standardized DPF differential pressure
-
Diff. Press. Sensor Corr.
Differential pressure sensor 0 point learned value
-
Exhaust Fuel Addition Injector Status
Exhaust fuel addition injector status
-
Exhaust Fuel Addition FB
Exhaust fuel addition correction value
-
DPNR/DPF Status Reju(PM)
PM forced regeneration status
-
PM Accumulation Ratio
PM accumulation ratio
-
Starter Signal
Starter signal
-
Neutral Position SW Signal
Neutral position switch signal
-
Clutch Switch
Clutch switch
-
Stop Light Switch
Stop light switch
-
A/C Signal
Air conditioning signal
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance after DTC cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTC cleared
-
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected
-
IG OFF Elapsed Time
Distance driven after battery cable disconnected
-
TC and TE1
TC and TE1 terminals of DLC3
-
Total Distance Traveled
Total distance traveled
-
Engine Speed (Starter Off)
-
This item is used for troubleshooting when DTC P1604 is stored.
Starter Count
-
This item is used for troubleshooting when DTC P1604 is stored.
Run Dist of Previous Trip
-
This item is used for troubleshooting when DTC P1604 is stored.
Glow Request Lighting Time
Glow request lighting time
This item is used for troubleshooting when DTC P1604 is stored.
IG-ON Time
Ignition switch ON time before engine start
This item is used for troubleshooting when DTC P1604 is stored.
MAF Low
Mass air flow low
This item is used for troubleshooting when DTC P1608 is stored.
Boost Pressure Low
Boost pressure low
This item is used for troubleshooting when DTC P1608 is stored.
Common Rail Pressure Low
Common rail pressure low
This item is used for troubleshooting when DTC P1608 is stored.
Engine Coolant Temp High
Engine coolant temperature high
This item is used for troubleshooting when DTC P1608 is stored.
MAF/Estimate MAF Ratio
Indicates the ratio of estimated intake air volume and the actual intake air volume
This item is used for troubleshooting when DTC P1608 is stored.
Rough Idle #1
Rough idle status of cylinder 1
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #2
Rough idle status of cylinder 2
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #3
Rough idle status of cylinder 3
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #4
Rough idle status of cylinder 4
This item is used for troubleshooting when DTC P1605 is stored.
Electric Duty Feedback Value
-
-
A/C Duty Feedback Value
-
-
PS Duty Feedback Value
-
-
Idle Injection Volume (Min)
Idle minimum injection volume
-
Engine Starting Time
Engine starting time
-
Minimum Engine Speed
Minimum engine speed
-
Swirl Control Valve VSV
VSV for swirl control valve
-
Electric Fan Motor
Electric fan motor
-
Brake Override System
Brake override system
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Communication with ECT
Communication with ECT
-
Received MIL from ECT
MIL status from ECT
-
Shift Position Sig from ECT
Shift position from ECT
-
A/T Oil Temp from ECT
ATF temperature from ECT
-
SPD (NO)
Output shaft speed
-
ECT Lock Up
ECT lock-up status
-
Shift SW Status (P Range)
Shift Switch Status (P Range)
-
Shift SW Status (R Range)
Shift Switch Status (R Range)
-
A/T Oil Temperature 1
ATF temperature sensor value
-
← DTC CHECK / CLEAR (from Jan 2017)CHECK MODE PROCEDURE (from Oct 2014) →