P0116 Engine Coolant Temperature Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
Refer to DTC P0115 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0116 |
When either of the following conditions is met (2 trip detection logic):
|
|
Engine coolant temperature is between -40°C and 60°C (-40°F and 140°F) when engine is started, and conditions (a) and (b) are met (2 trip detection logic):
|
MONITOR DESCRIPTION
- Engine coolant temperature (ECT) sensor cold start monitor
When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
- ECT sensor soak monitor
If the ECT sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
- ECT sensor high side stuck monitor
The ECM monitors the sensor voltage and uses this value to calculate the ECT. If the sensor voltage output deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the ECT sensor and stores the DTC.
MONITOR STRATEGY
| Required Sensors/Components |
Engine coolant temperature sensor |
| Frequency of Operation |
Once per driving cycle |
CONFIRMATION DRIVING PATTERN


- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
- Check that the engine coolant temperature is 60°C (140°F) or less.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for at least 30 seconds.
- Turn the ignition switch to ON and turn the GTS on [A].
- Start the engine and idle it for 5 minutes or more [B].
- HINT:
- If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.
- Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
- Read the Pending DTCs.
- HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- If a pending DTC is output, the system is malfunctioning.
- Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
- Input the DTC: P0116.
- Check the DTC judgment result.
GTS Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
- If the judgment result shows NORMAL, the system is normal.
- DTC judgment completed
- Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].
- CAUTION:
- When performing the confirmation driving pattern, obey all speed limits and traffic laws.
- HINT:
- In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.
- Check the DTC judgment result again [E].
- HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.
- If the judgment result shows NORMAL, the system is normal.
INSPECTION PROCEDURE
- HINT:
- If any of DTCs P0115, P0117 or P0118 are set simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
- If any of DTCs P0115, P0117 or P0118 are set simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
DTC P0116 is output
A
DTC P0116 and other DTCs are output
B
- HINT:
- If any DTCs other than P0116 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. INSPECT THERMOSTAT |
Remove the thermostat (Click here).
Measure the valve opening temperature of the thermostat.
- Standard:
- 80°C to 84°C (176°F to 183°F)
- HINT:
- In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.
Reinstall the thermostat (Click here).
- HINT:
- Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).
|
|
||||
| OK | ||
| ||
