2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT STARTER ARMATURE ASSEMBLY

  1. A082643
    Measure the resistance.

    1. Measure the resistance between the segments of the commutator.

      Standard Resistance:
      Tester Connection
      Connection
      Specified Condition
      Segment - Segment
      Always
      Below 1.7 Ω

      If the result is not as specified, replace the armature assembly.

    2. A082644
      Measure the resistance between a segment of the commutator and armature coil core.

      Standard Resistance:
      Tester Connection
      Connection
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      If the result is not as specified, replace the armature assembly.

  1. A082645
    Inspect the commutator circle runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Standard circle runout:
      0.02 mm (0.000787 in.)

      Maximum circle runout:
      0.04 mm (0.00157 in.)

      If the runout is more than the maximum, replace the armature assembly.

  1. A105696
    Using a vernier caliper, measure the commutator diameter.

    Standard commutator diameter:
    32.2 mm (1.27 in.)

    Minimum commutator diameter:
    31.1 mm (1.22 in.)

    If the diameter is less than the minimum, replace the armature assembly.

  1. A105577
    Using a vernier caliper, measure the undercut depth of the commutator.

    Standard undercut depth:
    0.9 mm (0.0354 in.)

    Minimum undercut depth:
    0.4 mm (0.0157 in.)

    If the depth is less than the minimum, replace the armature assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A123771
    Using a vernier caliper, measure the brush length.

    Standard brush length:
    14.0 mm (0.551 in.)

    Minimum brush length:
    9.0 mm (0.354 in.)

    If the length is less than the minimum, replace the starter brush holder assembly.

  1. A104910E01
    Check the brush holder.

    1. Measure the resistance between the brushes.

      Standard Resistance:
      Tester Connection
      Specified Condition
      A - B
      10 kΩ or higher
      A - C
      10 kΩ or higher
      A - D
      Below 1 Ω
      B - C
      Below 1 Ω
      B - D
      10 kΩ or higher
      C - D
      10 kΩ or higher

      If the result is not as specified, replace the starter brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A121932E01
    Check the starter clutch pinion gear.

    1. Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
      If the result is not as specified, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A105370E01
    Check the plunger.

    1. Install the plunger and spring onto the switch body.

    2. A104908
      Push in the plunger and check that it returns quickly to its original position.
      If the result is not as specified, replace the magnet starter switch assemby.

  1. A121933E01
    Check if the pull-in coil has an open circuit.

    1. Measure the resistance between terminal 50 and terminal C.

      Standard Resistance:
      Tester Connection
      Connection
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.

  1. A121934E01
    Check if the hold-in coil has an open circuit.

    1. Measure the resistance between terminal 50 and the switch body.

      Standard Resistance:
      Tester Connection
      Connection
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →