2014-2019 Hiace · Service Manual ENGINE

P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
DTC No.
DTC Detection Condition
Trouble Area
P0327
Output voltage of the knock sensor is 0.5 V or less (1 trip detection logic).
  1. Short in knock sensor circuit
  1. Knock sensor
  1. ECM
P0328
Output voltage of the knock sensor is 4.5 V or higher (1 trip detection logic).
  1. Open in knock sensor circuit
  1. Knock sensor
  1. ECM

HINT:
When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

Reference: Inspection using an oscilloscope
A150243E01
Tester Connection
Tool Setting
Condition
Specified Condition
D116-122 (KNK1) - D116-121 (EKNK)
1 V/DIV.
1 msec./DIV.
Engine speed at 4000 rpm with warm engine
The correct waveform is as shown

MONITOR DESCRIPTION

The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

MONITOR STRATEGY

Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Start the engine and wait 5 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0327 or P0328.
  11. Check the DTC judgment result.
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.


WIRING DIAGRAM

A247767E07

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT KNOCK SENSOR
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D116-122 (KNK1) - D116-121 (EKNK)
    20°C (68°F)
    120 to 280 kΩ



NG
Go to step 3
OK


2. INSPECT ECM
A161605E53
  1. Disconnect the Dg1 connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Dg1 female connector 1 - 2
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Female
    *a
    Front view of wire harness connector
    (to ECM Wire)



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
  1. Disconnect the ECM connector.

  1. Disconnect the knock sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    g1-2 - D116-122 (KNK1)
    Always
    Below 1 Ω
    g1-1 - D116-121 (EKNK)
    Always
    Below 1 Ω
    g1-2 or D116-122 (KNK1) - Body ground
    Always
    10 kΩ or higher
    g1-1 or D116-121 (EKNK) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Perform "Inspection After Repair" after replacing the knock sensor (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)


← P0300 Random / Multiple Cylinder Misfire Detected (+ P0301, P0302, P0303, P0304) (from Jan 2017)P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (+ P0328) (Apr 2016 – Dec 2016) →