2014-2019 Hiace · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Oct 2014


DESCRIPTION
Freeze frame data records the engine conditions (fuel system information, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.
These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
G038619E06

HINT:
If it is impossible to duplicate the problem even though a DTC is output, confirm the freeze frame data.

  1. 3 data sets from before the DTC was stored
  2. 1 data set from when the DTC was stored
  3. 1 data set from after the DTC was stored

LIST OF FREEZE FRAME DATA
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on the speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Load calculated by the ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If the value is approximately 0.0 gm/s:
  1. Mass air flow meter power source circuit is open.
  1. VG circuit is open or shorted.
If the value is 160.0 gm/s or more:
  1. E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Radiator Coolant Temp
Engine coolant (radiator) temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Throttle sensor position
Read the value with the ignition switch ON (do not start engine).
Throttle Sensor #2 Volt %
Throttle sensor position #2
Read the value with the ignition switch ON (do not start engine).
Throttle Sensor Position
Throttle position
Read the value with the ignition switch ON (do not start engine).
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle position
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
ISC Feedback Value
ISC feedback compensation amount
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state
For use when engine stall, starting problems or rough idle is present.
N Range Status
Shift lever N status
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate
For use when engine stall, starting problems or rough idle is present.
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump status
-
Current Fuel Type
Status of the current fuel type
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Purge density learned value
-
EVAP Purge VSV
EVAP purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Air-fuel ratio
-
AF Lambda B1S1
Fuel trim at air fuel ratio sensor
-
AFS Voltage B1S1
Air fuel ratio sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the air fuel ratio sensor.
AFS Current B1S1
Air fuel ratio sensor current
-
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio
-
O2S B1S2
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the heated oxygen sensor.
O2 Heater B1S2
Heated oxygen sensor heater
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current
-
Short FT #1
Short-term fuel trim
Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
  1. Overall fuel compensation is carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
  2. Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
A/F Learn Value Idle #1
Air-fuel ratio learned value for idling (bank 1)
Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
A/F Learn Value Low #1
Air-fuel ratio learned value for low engine loads (bank 1)
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid1 #1
Air-fuel ratio learned value for mid-sized engine loads 1 (bank 1)
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
A/F Learn Value Mid2 #1
Air-fuel ratio learned value for mid-sized engine loads 2 (bank 1)
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
A/F Learn Value High #1
Air-fuel ratio learned value for high engine loads (bank 1)
Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
Total FT #1
Total fuel trim
-
Fuel System Status #1
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go closed loop.
  2. CL (Closed Loop): Using the air fuel ratio sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the air fuel ratio sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (Bank 2)
-
Air pump pressure (Absolute)
Air pump pressure
-
Air Pump Pulsation Pressure
Air pump pulsation pressure
-
Secondary Air Control VSV
Secondary air injection system status
-
2nd Air System Status
Secondary air system status
-
AI Test
Secondary air injection system operation prohibition
-
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Knock Feedback Value
Knocking feedback value
-
Knock Correct Learn Value
Knocking correction learned value
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
For use when engine stall, starting problems or rough idle is present.
Actual VVT Angle #1
Actual VVT displacement angle (bank 1)
This is only available in Freeze Frame Data.
VVT Control Status #1
VVT control status
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Catalyst temperature
-
Catalyst Temp B1S2
Catalyst temperature
-
Starter Signal
Starter signal
-
Power Steering Signal
Power steering signal
-
Power Steer. Sig. Record
Power steering signal
This signal status usually ON until ignition switch turned to OFF
Neutral Position SW Signal
Park/neutral position switch signal
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
Electrical Load Signal
Electrical load signal
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTCs cleared
-
Distance from DTC Cleared
Accumulated distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared
-
Dist Batt Cable Disconnect
Total distance vehicle driven after battery cable disconnected
-
IG OFF Elapsed Time
Cumulative time after ignition switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Total Distance Traveled
Total distance traveled
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
All Cylinders Misfire Count
Misfire count of all cylinders
-
Misfire RPM
Misfire RPM
-
Misfire Load
Misfire load
-
Misfire Margin
Misfire monitoring
-
Engine Speed (Starter Off)
Engine speed when starter off
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature for A/C
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start
For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start
History of low engine speed after engine start
For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed
Minimum engine speed
For use when engine stall, starting problems or rough idle is present.
Fuel Cut Elps Time
Time elapsed after engine runs at high speed
-
ACT VSV
A/C cut status for Active Test
-
Electric Fan Motor
Electric fan motor status
-
Brake Override System
Brake override system status
-
Idle Fuel Cut
Fuel cut at idle
ON: The throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut during very light load
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
Electrical Load Signal 3
Electrical load signal
-
← DTC CHECK / CLEAR (from Dec 2017)CHECK MODE PROCEDURE (from Oct 2014) →