2014-2019 Hiace · Service Manual ENGINE

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Oct 2014


DESCRIPTION
Freeze frame data records the engine conditions (fuel system information, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.
The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the intelligent tester, 5 separate sets of freeze frame data can be checked.
These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.
G038619E06

HINT:
If it is impossible to duplicate the problem even though a DTC is output, confirm the freeze frame data.

  1. 3 data sets from before the DTC was stored
  2. 1 data set from when the DTC was stored
  3. 1 data set from after the DTC was stored

LIST OF FREEZE FRAME DATA
*: Except leaded gasoline specification vehicle
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on the speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Load calculated by the ECM.
MAF
Mass air flow volume
If the value is approximately 0.0 gm/s:
  1. Mass air flow meter power source circuit is open.
  1. VG circuit is open or shorted.
If the value is 160.0 gm/s or more:
  1. E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Intake Air
Intake air temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Radiator Coolant Temp
Engine coolant (radiator) temperature
If the value is -40°C, the sensor circuit is open.
If the value is 140°C, the sensor circuit is shorted.
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute accelerator pedal position No. 1
-
Accel Sens. No. 2 Volt %
Absolute accelerator pedal position No. 2
-
Throttle Sensor Volt %
Throttle sensor position
Read the value with the ignition switch ON (do not start engine).
Throttle Sensor #2 Volt %
Throttle sensor position #2
Read the value with the ignition switch ON (do not start engine).
Throttle Sensor Position
Throttle position
Read the value with the ignition switch ON (do not start engine).
Throttle Motor DUTY
Throttle actuator
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump status
-
Evap Purge Flow*
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value*
Purge density learned value
-
EVAP Purge VSV*
EVAP purge VSV
-
Target Air-Fuel Ratio*
Air-fuel ratio
-
O2S B1S1*
Heated oxygen sensor output
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the heated oxygen sensor.
Short FT #1*
Short-term fuel trim
Short-term fuel compensation is used to maintain the heated oxygen sensor at the stoichiometric air-fuel ratio.
Long FT #1*
Long-term fuel trim
Overall fuel compensation is carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
Fuel System Status #1*
Fuel system status (Bank 1)
  1. OL (Open Loop): Has not yet satisfied the conditions to go closed loop.
  2. CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
  3. OLDrive: Open loop due to driving conditions (fuel enrichment).
  4. OLFault: Open loop due to a detected system fault.
  5. CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2*
Fuel system status (Bank 2)
-
O2FT B1S1*
Fuel trim at heated oxygen sensor
-
IGN Advance
Ignition timing advance for No. 1 cylinder
-
Knock Feedback Value
Knocking feedback value
-
Knock Correct Learn Value
Knocking correction learned value
-
VVT Control Status #1
VVT control status
-
Starter Signal
Starter signal
-
Power Steering Signal
Power steering signal
-
Power Steer. Sig. Record
Power steering signal
This signal status usually ON until ignition switch turned to OFF
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTCs cleared
-
Distance from DTC Cleared
Accumulated distance driven after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Electric Fan Motor
Electric fan motor status
-
Idle Fuel Cut
Fuel cut at idle
ON: The throttle valve is fully closed and the engine speed is more than 2800 rpm.
FC TAU
Fuel cut during very light load
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
← DTC CHECK / CLEAR (from Dec 2015)CHECK MODE PROCEDURE (from Oct 2014) →