2014-2019 Hiace · Service Manual ENGINE

INITIALIZATION

Troubleshooting · Vehicles built from Oct 2014


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER SUB-ASSEMBLY

HINT:
When the diesel throttle body assembly, electric EGR control valve assembly or turbocharger sub-assembly is replaced, perform initialization

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  2. Turn the ignition switch off and wait for 30 seconds or more.

  3. Turn the ignition switch to ON and wait for 10 seconds or more.


CATALYST RECORD OF DPF THERMAL DETERIORATION CLEAR FUNCTION

HINT:
When the DPF catalyst is replaced, the catalyst record of DPF thermal deterioration stored in the ECM must be cleared.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. A320569
    Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Catalyst Record Clear.

  5. Press "Next".

  6. A320570
    Press "Exit".


FUEL SUPPLY PUMP INITIALIZATION PROCEDURE

HINT:
After replacing the fuel supply pump assembly and/or ECM:
  1. If the engine is defective or stalls immediately after startup, the learned values of the ECM must be initialized. The engine can be initialized through the GTS or by connecting DLC3 terminals.
  2. If the engine starts normally, initialization is not necessary. Perform the steps labeled procedure "A" and procedure "B" only.

  1. A280985
    Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / Supply Pump Initialization.

  5. Press "Next".

  6. A280986
    Press "Next".

  7. A280987
    Press "Exit".

  8. Start the engine to check if the initialization is complete. If the engine cannot be started, repeat the initialization procedures from the beginning (Procedure "A").

  9. Idle the engine for at least 1 minute under the following conditions: (Procedure "B")

    1. The engine coolant temperature is 60°C (140°F) or higher.
    2. The fuel temperature is 20°C (68°F) or higher.

    NOTICE:
    Do not race the engine immediately after starting the engine. After warming up the engine, racing the engine is acceptable.

    HINT:
    1. The engine coolant temperature can be estimated by touching the outlet hose.
    2. The fuel temperature can be estimated by using the ambient temperature as a substitute.
    3. If the engine coolant temperature is difficult to estimate, use the GTS and enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  10. Initialization is complete.


CRANK TIME COMPENSATION RESET FUNCTION
  1. This procedure uses the GTS to perform "Crank Time Compensation Reset".
  2. When replacing the No. 1 crankshaft position sensor plate (engine assembly), perform "Crank Time Compensation Reset".

HINT:

  1. A204035
    If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.
  2. A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / Crank Time Compensation Reset.

  5. A280989
    When the first screen is displayed, check the vehicle condition and push "Next".

  6. A280984
    When the screen indicating reset completion is displayed, push "Exit".


A/F SENSOR COMPENSATION RESET FUNCTION
  1. This procedure uses the GTS to perform "A/F Sensor Compensation Reset".
  2. When replacing the A/F sensor, replace the sensor and then perform "A/F Sensor Compensation Reset".

HINT:

  1. A204038
    If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.
  2. A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / A/F Sensor Compensation Reset.

  5. A320567
    When the first screen is displayed, check the vehicle condition and push "Next".

  6. A320568
    When the screen indicating reset completion is displayed, push "Exit".

← REGISTRATION (from Jan 2017)PROBLEM SYMPTOMS TABLE (Oct 2014 – Dec 2014) →