2014-2019 Hiace · Service Manual ENGINE

REGISTRATION

Other · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. LEARNING VALUES CONFIRMATION

This procedure uses the GTS to display the learned values (injector compensation code, pilot quantity initial learning value, pilot quantity deterioration learning value, pilot quantity current learning value, pilot quantity learning value, crank time compensation learning value, A/F sensor learning value and catalyst deterioration learning value) stored in the ECM.

A321530E01

HINT:

  1. A204047
    A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

  1. A266977
    Press "Next".

  1. A266978
    Press "Next" again to proceed.

  1. A320571
    Select the value to confirm and press "Next".

  1. A320572
    When the next screen is displayed, confirm the contents and press "Exit".


2. LEARNING VALUES SAVE

This procedure uses the GTS to save the learned values (injector compensation code) stored in the ECM in the GTS depending on the components being replaced.

A209877E13

HINT:
  1. When replacing the engine assembly, injector assembly together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

  2. A204057
    When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

  3. A204058
    A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.

  1. A268095
    Press "Next".

  1. A268096
    Press "Next" again to proceed.

  1. A321531
    Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.

  1. A204055
    If the overwrite confirmation screen is displayed, press "Overwrite".

  1. A268098
    When the operation is finished, confirm the date and time of the save operation, and press "Exit".


3. LEARNING VALUES WRITE

This procedure uses the GTS to write all of the learned values (injector compensation code) stored in the GTS to the ECM.

A202034E02

HINT:

  1. A204063
    A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.

  1. A268099
    Press "Next".

  1. A268100
    Press "Next" again to proceed.

  1. A204062
    If the "Error Learning Values Write" screen indicating a problem with the saved value(s) or that there are no saved values is displayed, perform "Learning Values Save" again.

  1. A204064
    Confirm the date and time of the save operation, and then press "Yes".

  1. Confirm the contents, and then press "Next".

  1. A321532
    If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.

  1. Clear the DTCs.


4. AFTER REPLACING INJECTOR(S) WITH NEW ONE(S), INPUT COMPENSATION CODE(S) OF INJECTOR(S) INTO ECM AS FOLLOWS:

NOTICE:
  1. When an injector is replaced, the injector's compensation code must be input into the ECM. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.
  2. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

  1. A085701E01
    Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS ON.

    NOTICE:
    Do not start the engine.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.

  1. A321636
    Enter the menu options in this order: Powertrain / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A321637
    Press Next again to proceed.

  1. A321638
    Select "Set Compensation Code".

  1. Press Next.

  1. A321639
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

  1. A321640
    Register compensation code.

    1. Press input.

    2. A321641
      Manually input the cylinder's compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value imprinted on the injector's head portion.

      HINT:
      Each injector compensation code is unique. The correct compensation code must be input into each cylinder selected on the GTS.

    3. Confirm that the compensation code is correct for the selected cylinder is correct, and then press OK.

  1. A321642
    Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.

    NOTICE:
    If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    HINT:
    If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. Press Next to set the compensation code to the ECM.

    HINT:
    1. If the setting process fails, the compensation code may be incorrect. Check the compensation code again.
    2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A321643
    If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.

  1. Turn the GTS OFF and then turn the ignition switch OFF.

  1. Wait for at least 30 seconds.

  1. Turn the ignition switch ON and then turn the GTS ON.

  1. Clear DTC P1601 stored in the ECM using the GTS (Click here).


5. WHEN REPLACING ECM WITH NEW ONE, INPUT ALL INJECTOR'S COMPENSATION CODES INTO NEW ECM AS FOLLOWS:

NOTICE:
  1. When an injector is replaced, the injector's compensation code must be input into the ECM. When the ECM is changed, all of the existing injector compensation codes must be input into the new ECM.
  2. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

HINT:
The following operation is available with ECMs that can transmit the registered injector compensation codes to the GTS.

  1. A085701E01
    Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS ON.

    NOTICE:
    Do not start the engine.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.

  1. A321636
    Enter the menu options in this order: Power train / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A321637
    Press Next again to proceed.

  1. A321644
    Select Read Compensation Code.

  1. Press Next.

  1. A321639
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

    HINT:
    The reading process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A321645
    Check the injector compensation code (30-digit alphanumeric value) is displayed on the GTS screen.

  1. Press Save.

  1. A108923E01
    Check that the compensation code displayed on the GTS screen is correct.

  1. Press Save or Replace, save the injector compensation code.

    HINT:
    1. The existing compensation code is overwritten with the new compensation code and is deleted from the GTS.
    2. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A321645
    If you want to read and save other injector compensation codes for other cylinders, press Next to continue. To finish this operation, press Cancel.

  1. Turn the ignition switch OFF.

  1. Turn the GTS OFF.

  1. Replace the ECM.

  1. A085701E01
    Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS ON.

    NOTICE:
    Do not start the engine.

    HINT:
    The injector compensation code is imprinted on the head portion of each injector.

  1. A321636
    Enter the menu options in this order: Power train / Engine and ECT / Utility / Injector Compensation.

  1. Press Next.

  1. A321637
    Press Next again to proceed.

  1. A321638
    Select Set Compensation Code.

  1. Press Next.

  1. A321639
    Select the number of the cylinder corresponding to the injector compensation code that you want to read.

  1. Press Next.

  1. A321642
    Check that the compensation code displayed on the screen is correct, by comparing it with the 30-digit alphanumeric value on the head portion of the injector.

    NOTICE:
    If an incorrect injector compensation code was input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    HINT:
    If a wrong compensation code was input or read, return to the input Value screen by pressing input. The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

  1. Press Next to set the compensation code to the ECM.

    HINT:
    1. If the setting fails, the compensation code may be incorrect. Check the compensation code again.
    2. If the attempted compensation code is correct, a problem with the wire harness or a bad connection with the DLC3 may cause the failure. Check the wire harness and the DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

  1. A321643
    If you want to continue with other compensation code registrations, press Next. To finish the registration, press Cancel.

  1. Turn the GTS OFF and then turn the ignition switch OFF.

  1. Wait for at least 30 seconds.

  1. Turn the ignition switch ON and then turn the GTS ON.

  1. Clear DTC P1601 stored in the ECM using the GTS (Click here).

← BASIC INSPECTION (from Oct 2014)REGISTRATION (Jan 2015 – Mar 2016) →