REGISTRATION
Other · Vehicles built from Oct 2014
- HINT:
- If replacing the door control transmitter or the door control receiver, register its recognition code to the instrument panel junction block assembly (body ECU).
- The add mode is used to register new recognition codes while still retaining codes already registered. This mode is used when a new transmitter is added. If the number of registered codes exceeds 6, the previously registered codes will be erased in order, starting from the oldest registered code.
- The rewrite mode is used to erase all the previously registered recognition codes in order to register all-new recognition codes. This mode is used when the transmitter or the door control receiver is replaced.
- The confirmation mode is used to confirm how many recognition codes have already been registered before another recognition code is registered.
- The prohibition mode is used to erase all the registered codes and disable the wireless door lock function. This mode is used when the transmitter is lost.
- All of the following registration procedures must be performed in order.
- If replacing the door control transmitter or the door control receiver, register its recognition code to the instrument panel junction block assembly (body ECU).
| 1. PROCEDURE FOR RECOGNITION CODE REGISTRATION |
The following conditions should be met before starting the procedure:
- No key is in the ignition key cylinder.
- Only driver side door is open.
- No key is in the ignition key cylinder.
Insert the key into the ignition key cylinder, then pull it out (Procedure "A").
Insert the key into the ignition key cylinder, then pull it out within 5 seconds after procedure "A" (Procedure "B").
Close and open the driver side door twice.
Insert the key into the ignition key cylinder, then pull it out within 40 seconds after procedure "B" (Procedure "C").
Close and open the driver side door twice.
Insert the key into the ignition key cylinder and close all doors within 40 seconds after procedure "C" (Procedure "D").
Turn the ignition switch from the off to the ON position and back to the off position at approximately 1 second intervals according to the number of times shown in the table below.
Number of ON-off operations of ignition switch: Mode Selection
Ignition Switch ON-off Operation
Ignition Key Position
Add mode
Once


- A: Ignition switch position "ON"
- B: Ignition switch position "off"
- T1: Approximately 1 second
Rewrite Mode
Twice


- A: Ignition switch position "ON"
- B: Ignition switch position "off"
- T1: Approximately 1 second
Confirmation Mode
3 times


- A: Ignition switch position "ON"
- B: Ignition switch position "off"
- T1: Approximately 1 second
Prohibition Mode
5 times


- A: Ignition switch position "ON"
- B: Ignition switch position "off"
- T1: Approximately 1 second
- A: Ignition switch position "ON"
Remove the key from the ignition key cylinder within 40 seconds after the procedure "D" (Procedure "E").
The instrument panel junction block assembly (body ECU) automatically performs power door lock-unlock operations to indicate which mode has been selected.
- HINT:
- If the number of ON-off operations of the ignition switch is 0, 4 or 6 or more, there will be no response (power door lock-unlock operation).
Response to selected mode (Power door lock operation): Mode Selection
Power Door Lock Lock-unlock
Door Lock Status
Add mode
1 cycle


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- E: 1 cycle
- T1: Approximately 1 second
Rewrite Mode
2 cycles


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- E: 1 cycle
- T1: Approximately 1 second
Confirmation Mode
The number of registered codes (1 to 4 cycles)


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- C: 1st time
- D: 2nd time
- E: 1 cycle
- T2: Approximately 2 seconds
Prohibition Mode
5 cycles


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- E: 1 cycle
- T1: Approximately 1 second
- HINT:
- In confirmation mode, lock-unlock operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, lock-unlock movement will occur twice.
- In confirmation mode, if no recognition codes have been registered, lock-unlock operation will occur 11 times.
- In confirmation mode, lock-unlock operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, lock-unlock movement will occur twice.
- Next step:
Mode Selection
Procedure
Add Mode
Continued on next step.
Rewrite Mode
Confirmation Mode
Registration procedures are completed.
Prohibition Mode
Press both lock and unlock switches on the transmitter simultaneously for 1 second or more. (Procedure F)
Press either lock or unlock switch for 1 second or more within 45 seconds after performing procedure E.
The instrument panel junction block assembly (body ECU) automatically performs power door lock-unlock operations to indicate whether registration has been completed correctly.
Response to registration completion: Power Door Lock Lock-unlock Operation
Result
Door Lock Status
1 cycle
Registration of recognition code has been completed.


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- E: 1 cycle
- T1: Approximately 1 second
2 cycles
Registration of recognition code has failed.


- A: Door lock motor status "lock"
- B: Door lock motor status "unlock"
- E: 1 cycle
- T1: Approximately 1 second
- HINT:
- If registration of recognition code has failed, perform registration procedures again from the beginning.
- Next step:
Next Operation
Procedure
Another transmitter needs to be registered.
Return to procedure "F" within 40 seconds (*1).
Finish registration procedure.
Continued on next step.
- HINT:
- *1: All 6 recognition codes can be registered consecutively.
- A: Door lock motor status "lock"
Perform either of the following:
- Open a door.
- Insert the key into the ignition key cylinder.
- Open a door.
Registration of recognition codes (add mode and rewrite mode) is completed.
