2014-2019 Hiace · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Jan 2017 – Nov 2017

Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017


1. CLEAN WINDSHIELD GLASS

  1. B073128E02
    Using a scraper, remove the stoppers, dams and adhesive sticking to the windshield glass.

  1. Clean the outer edges of the windshield glass with non-residue solvent.

    NOTICE:
    1. Do not touch the windshield glass surface after cleaning it.
    2. Even if using new windshield glass, clean the windshield glass with non-residue solvent.


2. CLEAN VEHICLE BODY

  1. B073084E13
    Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.

      Text in Illustration 
      *1
      Adhesive
      *2
      Vehicle Body


3. INSTALL WINDSHIELD GLASS STOPPER
  1. Apply Primer G to the installation part of the spacers.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the windshield glass, as shown in the illustration.

    B101847E02

    Text in Illustration 
    *1
    Primer G
    *2
    Ceramic Line
    *3
    Ceramic Notch
    -
    -
    *a
    Backside
    -
    -

    Specification:
    Area
    Measurement
    a
    20.0 mm (0.787 in.)
    b
    9.0 mm (0.354 in.)
    c
    10.0 mm (0.393 in.)


4. INSTALL WINDSHIELD GLASS ADHESIVE DAM
  1. Apply Primer G to the installation part of the windshield glass adhesive dams.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install new windshield glass adhesive dams all the way around the windshield glass except where the spacers are installed, as shown in the illustration.

    B101848E03

    Text in Illustration 
    *1
    Ceramic Notch
    *2
    Ceramic Line
    *a
    Backside
    *b
    Cut Line

    Specification:
    Area
    Measurement
    a
    7.0 mm (0.276 in.)
    b
    23.2 mm (0.913 in.)


5. INSTALL WINDSHIELD GLASS

  1. B115414E02
    Position the windshield glass.

    1. Using a suction cup, place the windshield glass in the correct position.

    2. Check that the whole contact surface of the windshield glass rim is perfectly even.

    3. Place matchmarks over the windshield glass and vehicle body on the locations indicated in the illustration.

      HINT:
      1. Placing matchmarks is only necessary if the windshield glass being installed is new. If it is reused windshield glass, matchmarks should already be present.
      2. When reusing the windshield glass, check and correct the matchmark positions.

      NOTICE:
      Check that the spacers are attached to the vehicle body correctly.

    4. Using a suction cup, remove the windshield glass.

      Text in Illustration 
      *1
      Matchmark

  1. B083465E02
    Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

    Text in Illustration 
    *A
    CORRECT
    *B
    INCORRECT
    *1
    Primer M
    *2
    Adhesive

  1. Using a brush or sponge, apply Primer G to the contact surface of the windshield glass.

    B114784E02

    Text in Illustration 
    *1
    Primer G
    *2
    Adhesive Center Line
    *a
    Backside
    -
    -

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. B115241E02
      Cut off the tip of the cartridge nozzle, as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time described in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the windshield glass as shown as shown in the illustration.

      B101852E02

      Text in Illustration 
      *1
      Adhesive
      -
      -
      *a
      Backside
      -
      -

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

  1. B073132E07
    Install the windshield glass to the vehicle body.

    1. Using a suction cup, position the windshield glass so that the matchmarks are aligned. Press it in gently along the rim.

    2. Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

      NOTICE:
      1. Allow the primer to dry for 3 minutes or more.
      2. Check that the spacers are attached to the vehicle body correctly.
      3. Check that the vehicle body and windshield glass have a small gap between them.

    3. Hold the windshield glass in place securely with protective tape or equivalent until the adhesive hardens.

      Text in Illustration 
      *1
      Matchmark


6. INSTALL OUTER UPPER WINDSHIELD MOULDING

  1. B101849E02
    Using a brush or sponge, apply Primer G to the contact surface of the windshield glass.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    Text in Illustration 
    *1
    Reference Mark

  1. Install new outer upper windshield moulding, as shown in the illustration.

    NOTICE:
    Do not drive the vehicle for the amount of time described in the table below.

    Minimum Time:
    Temperature
    Minimum Time Prior to Driving Vehicle
    35°C (95°F)
    1 hour 30 minutes
    20°C (68°F)
    5 hours
    5°C (41°F)
    24 hours


7. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.


8. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E108766
    Engage the grommet as shown in the illustration.

  1. Install the windshield wiper motor and link assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the connector.


9. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E108767E01
    Body type narrow:

    1. Install the cowl top ventilator louver sub-assembly with the 10 claws and 6 clips.

  1. Body type wide:

    1. Install the cowl top ventilator louver sub-assembly with the 11 claws and 7clips.

  1. Connect the washer hose.


10. INSTALL COWL VENT COVER LH

11. INSTALL COWL VENT COVER RH

12. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. B108016E03
    Operate the wiper, and stop the windshield wiper motor assembly at the automatic stop position.

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).

  1. E108758E01
    Install the front wiper arm and blade assembly LH with the nut at the position as shown in the illustration.

    Torque:
    25 N*m{ 225 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.


13. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. B108016E03
    Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).

  1. E108757E01
    Install the front wiper arm and blade assembly RH with the nut at the position as shown in the illustration.

    Torque:
    25 N*m{ 225 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.


14. INSTALL WINDSHIELD WIPER ARM COVER
  1. Install the 2 windshield wiper arm covers.

  1. Operate the front wipers while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.


15. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
(Click here)

16. INSTALL ROOF NO.1 HEADLINING

17. INSTALL ROOM LIGHT ASSEMBLY NO. 1

18. INSTALL VISOR ASSEMBLY RH

19. INSTALL VISOR ASSEMBLY LH

20. INSTALL VISOR HOLDER

21. INSTALL ASSIST GRIP ASSEMBLY REAR

22. INSTALL FRONT PILLAR GARNISH LH

23. INSTALL FRONT PILLAR GARNISH RH

24. INSTALL ASSIST GRIP ASSEMBLY

25. INSTALL FRONT ASSIST GRIP PLUG
← INSTALLATION (Apr 2016 – Dec 2016)INSTALLATION (from Dec 2017) →