2014-2019 Hiace · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. CLEAN FRONT SIDE WINDOW GLASS

  1. B073128E02
    Using a scraper, remove the spacers, clips, dam and adhesive from the front side window glass.

  1. Clean the outer edge of the front side window glass with non-residue solvent.

    NOTICE:
    1. Do not touch the front side window glass surface after cleaning it.
    2. Even if using new front side window glass, clean the front side window glass with non-residue solvent.


2. CLEAN VEHICLE BODY

  1. B073084E13
    Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

      Text in Illustration 
      *1
      Adhesive
      *2
      Vehicle Body


3. INSTALL QUARTER WINDOW GLASS SPACER

  1. B102386E02
    Apply Primer G to the glass where the quarter window glass spacers will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new spacers onto the front side window glass as shown in the illustration.

    Text in Illustration 
    *1
    Quarter Window Glass Spacer
    *a
    Backside


4. INSTALL FRONT SIDE WINDOW CLIP LH
  1. Apply Primer G to the glass where the front side window clip will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install 2 new clips.


5. INSTALL NO. 1 FRONT SIDE WINDOW ADHESIVE DAM LH
  1. Apply Primer G to the glass where the No. 1 front side window adhesive dam will be installed.

    HINT:
    If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Install new dam.


6. INSTALL FRONT SIDE WINDOW SEAL SET PLATE LH (w/ Window Seal Set Plate)

NOTICE:
Be sure to replace the front side window seal set plate LH with a new one.

  1. B397559E01
    Apply primer to the installation area within the mark-off line of the front side window seal set plate LH shown in the illustration.

    NOTICE:
    Do not apply too much primer.

    Text in Illustration 
    *a
    Mark-off Line

  1. Apply adhesive to the front side window seal set plate LH shown in the illustration.

    B397561E01

    Text in Illustration 
    *a
    Installation Position: Center, Rear
    *b
    Installation Position: Front
    *c
    Adhesive
    -
    -

    Standard:
    Area
    Specified Condition
    a
    14.0 mm (0.551 in.)
    b
    10.0 mm (0.551 in.)

    NOTICE:
    Throw away any leftover Primer.

  1. Remove the peeling paper from the face of the front side window seal set plate LH.

  1. Set the position as shown in the illustration and install the front side window seal set plate LH to the area within the mark-off line.

    B397562E01

    Text in Illustration 
    *a
    Mark-off Line
    *b
    While lifting the surface that has double-sided tape attached, make contact with the bottom surface of the rail.
    *c
    While contacting the bottom surface of the rail, rotate and attach the double-sided tape.
    -
    -

    HINT:
    1. Front and rear position: Install to the area within the mark-off lines.
    2. Upper and lower position: Make contact with the bottom surface of the rail and install.

  1. After the adhesive hardens, pour a small amount of water into the rail water channel, being careful not to spill any, and check that the water drains from the lower section of the front side window seal set plate LH.

    B397564E01

    Text in Illustration 
    *a
    Water Channel
    *b
    OK: Water Drains from Bottom Tip Only


7. INSTALL FRONT SIDE WINDOW GLASS

  1. B114789E02
    Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the Primer M to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.

    Text in Illustration 
    *A
    CORRECT
    *B
    INCORRECT
    *1
    Primer M
    *2
    Adhesive

  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.

    B114785E02

    Text in Illustration 
    *A
    w/ Slide Door
    *B
    w/o Slide Door
    *1
    Primer G
    *2
    Adhesive Center Line
    *a
    Backside
    -
    -

    HINT:
    If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the Primer G to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. B115241E03
      Cut off the tip of cartridge nozzle as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage Time Frame 
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the front side window glass as shown in the illustration.

      B397566E01

      Text in Illustration 
      *A
      w/ Slide Door
      *B
      w/o Slide Door
      *C
      w/ Window Seal Set Plate
      -
      -
      *1
      Adhesive
      *2
      Adhesive Center Line
      *3
      EPT Sealer
      *4
      Font Side Window Seal Set Plate LH
      *a
      Backside
      -
      -

      NOTICE:
      1. Apply adhesive at a constant height, even above the front side window seal set plate LH. (w/ Window Seal Set Plate)
      2. Do not apply sealant beyond the EPT sealer area. (w/ Window Seal Set Plate)

      Specification 
      Area
      Measurement
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      25.1 mm (0.988 in.)
      d
      14.1 mm (0.555 in.)
      e
      11.5 mm (0.452 in.)
      f
      6.0 mm (0.236 in.)

      NOTICE:
      1. Apply adhesive at a constant height, even above the front side window seal set plate LH. (w/ Window Seal Set Plate)
      2. Do not apply sealant beyond the EPT sealer area. (w/ Window Seal Set Plate)

  1. Install the front side window glass to the vehicle body.

    1. Lightly press the front surface of the front side window glass to ensure that the front side window glass is securely fit to the vehicle body.

      NOTICE:
      1. Check that the spacers are attached to the vehicle body correctly.
      2. Check that the vehicle body and front side window glass have a small gap between them.

    2. Hold the front side window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      Do not drive the vehicle for the amount of time written in the table below.

      Minimum Time 
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours


8. INSTALL EMERGENCY HAMMER CAUTION PLATE (w/ Emergency Hammer Caution Plate)

HINT:
Only for the LH Side.

  1. Remove the peeling paper.

  1. Install the emergency hammer caution plate as shown in the illustration.

    B321929E01

    Text in Illustration 
    *1
    Ceramic Line
    -
    -
    *a
    Backside
    -
    -
    Specification 
    Area
    Measurement
    a
    815 mm (32.1 in.)


9. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.


10. INSTALL NO. 2 REAR DOOR TRIM MOULDING LH

11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B101171E01
    Engage the 19 clips and claw, and install the rear door trim board sub-assembly.

  1. B101169
    Using a "torx" socket wrench, install the 2 "torx" screws.


12. INSTALL SLIDE DOOR WINDOW GARNISH LH

  1. B101167E01
    Engage the clips and install the slide door window garnish.

← REASSEMBLY (from Oct 2014)INSTALLATION (from Jan 2017) →