INSTALLATION
Removal / installation · Vehicles built from Jan 2017
Versions by build date: Oct 2014 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| 1.
CLEAN REAR SIDE WINDOW GLASS |
 |
- Using a scraper, remove the spacers, moulding and adhesive from the back door glass.
Clean the outer edge of the back door glass with non-residue solvent.
- NOTICE:
- Do not touch the back door glass surface after cleaning it.
- Even if using new back door glass, clean the back door glass with non-residue solvent.
| 2.
CLEAN VEHICLE BODY |
 |
- Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
- HINT:
- Leave as much adhesive on the vehicle body as possible.
- NOTICE:
- Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
- HINT:
- Even if all the adhesive has been removed, clean the vehicle body.
| 3.
INSTALL REAR SIDE WINDOW GLASS STOPPER |
 |
- Apply Primer G to the glass where the spacers will be installed.
- HINT:
- If primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
- NOTICE:
- Allow the Primer G to dry for 3 minutes or more.
- Throw away any leftover Primer G.
- Do not apply too much Primer G.
| 4.
INSTALL REAR SIDE WINDOW GLASS |
 |
- Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
- HINT:
- Allow the Primer M to dry for 3 minutes or more.
- Do not apply Primer M to the adhesive.
- Throw away any leftover Primer M.
- Do not apply too much Primer M.
Using a brush or sponge, apply Primer G to the contact surface of the glass.


- HINT:
- If Primer G is applied to an area other than that which is specified, wipe off the primer with non-residue solvent before it dries.
- NOTICE:
- Allow the Primer G to dry for 3 minutes or more.
- Throw away any leftover Primer G.
- Do not apply too much Primer G.
Apply adhesive to the back door glass.
- Adhesive:
- Toyota Genuine Windshield Glass Adhesive or equivalent
- Cut off the tip of cartridge nozzle as shown in the illustration.
- Specificatiom:
Area
|
Measurement
|
a
|
12.0 mm (0.472 in.)
|
b
|
8.0 mm (0.315 in.)
|
- HINT:
- After cutting off the tip, use all adhesive within the time written in the table below.
Usage timeframe
Temperature
|
Usage Timeframe
|
35°C (95°F)
|
15 minutes
|
20°C (68°F)
|
1 hour 40 minutes
|
5°C (41°F)
|
8 hours
|
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass as shown in the illustration.


Specification
Area
|
Measurement
|
a
|
12.0 mm (0.472 in.)
|
b
|
8.0 mm (0.315 in.)
|
c
|
6.1 mm (0.24 in.)
|
d
|
14.1 mm (0.587 in.)
|
e
|
11.5 mm (0.452 in.)
|
f
|
14.6 mm (0.574 in.)
|
Install the back door glass to the vehicle body.
Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.
- NOTICE:
- Check that the spacers are attached to the vehicle body correctly.
- Check that the vehicle body and back door glass have a small gap between them.
Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.
- NOTICE:
- Do not drive the vehicle for the amount of time written in the table below.
Minimum time
Temperature
|
Minimum time prior to driving vehicle
|
35 °C (95°F)
|
1 hour 30 minutes
|
20°C (68°F)
|
5 hours
|
5 °C(41°F)
|
24 hours
|
| 5.
CHECK FOR LEAKS AND REPAIR |
 |
Conduct a leak test after the adhesive has completely hardened.
| 6.
INSTALL ROOF SIDE GARNISH INNER UPPER LH |
|
| 7.
INSTALL QUARTER PILLAR GARNISH LH |
|
| 8.
INSTALL QUARTER TRIM PANEL ASSEMBLY REAR LH |
|
| 9.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
|
 |
- Connect the front seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 2 claws to close the cover.
- Connect the front seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 10.
INSTALL BACK DOOR WEATHERSTRIP |
|
| 11.
INSTALL BACK DOOR SCUFF PLATE |
|