2014-2019 Hiace · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO. 1

  1. B365541
    Using a moulding remover D, detach the 3 claws and remove the instrument cluster finish panel garnish No. 1.


3. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO. 2

  1. B102813
    Using a moulding remover D, detach the 3 claws and remove the instrument cluster finish panel garnish No. 2.


4. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER
  1. for Standard Body:
    Using a moulding remover D, detach the 4 claws in the order shown in the illustration.

  1. for Wide Body:
    Using a moulding remover D, detach the 5 claws in the order shown in the illustration.

    B365537E01

    Text in Illustration 
    *A
    for Standard Body
    *B
    for Wide Body

  1. B366735E01
    Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover D, detach the claw.

  1. B365539
    Detach the claw as shown in the illustration.

  1. B102817
    Detach the 3 claws as shown in the illustration.

  1. B102818
    Detach the 2 claws as shown in the illustration.

  1. for Standard Body:
    Detach the 3 claws and remove the instrument cluster finish panel sub-assembly center.

  1. for Wide Body:
    Detach the 4 claws and remove the instrument cluster finish panel sub-assembly center.

    B365540E01

    Text in Illustration 
    *A
    for Standard Body
    *B
    for Wide Body


5. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B365542
    Using a moulding remover D, detach the 4 claws and remove the instrument cluster finish panel assembly.


6. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B365543
    Detach the 6 claws and 4 hooks and remove the instrument cluster finish panel sub-assembly.


7. REMOVE COMBINATION METER ASSEMBLY

  1. B366842
    Remove the 2 screws.

  1. B366843
    Detach the 2 claws and remove the combination meter assembly.

  1. Disconnect the 2 connectors and detach the wire harness clamp.


8. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER

  1. B365544
    Using a clip remover, remove the 2 clips.

  1. Detach the 4 clips and remove the instrument panel finish lower.

  1. Disconnect each connector.

  1. B102838
    Push the positions indicated by the arrows in the illustration to disconnect the fuel lid lock control cable and bonnet (hood) control cable assembly from the instrument panel finish lower.


9. REMOVE NO. 2 STEERING COLUMN LOWER COVER (w/ Smart Entry and Start System)

  1. C299749
    Detach the 4 claws and remove the No. 2 steering column lower cover.


10. REMOVE STEERING COLUMN LOWER COVER

HINT:
Adjust the position of the steering tilt mechanism when performing the procedure.

  1. E286020
    While turning the steering wheel to the right.

  1. Using a T25 ''TORX'' socket wrench, remove the ''TORX'' screw.

  1. E286019
    While turning the steering wheel to the left.

  1. Using a T25 ''TORX'' socket wrench, remove the ''TORX'' screw.

  1. C299580
    Push the steering column lower cover inward on both sides to detach the 2 claws.

  1. E292452
    Detach the 2 claws and remove the steering column lower cover.


11. REMOVE STEERING COLUMN UPPER COVER

  1. C299599E01
    Remove the steering column upper cover from the steering column assembly.
    Text in Illustration 
    *a
    Front of Vehicle
    *b
    Raise the backside of the steering column upper cover
    *c
    Pull diagonally backwards so that the claw of the steering column upper cover does not break

    NOTICE:
    If the steering column upper cover is removed by pulling it directly upwards, the claw may become damaged.


12. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY
  1. Disconnect the 2 connectors.

  1. E286018
    Detach the claw and remove the windshield wiper switch assembly as shown in the illustration.

    NOTICE:
    If the claw is pushed with excessive force, it may be broken.

← REMOVAL (Oct 2014 – Dec 2014)REMOVAL (Apr 2016 – Dec 2016) →