2014-2019 Hiace · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014


DATA LIST

HINT:
By reading the Data List displayed on the intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    HINT:
    If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    600 to 700 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 26%: Idling
    2. 12 to 27%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from MAF meter/
    Min.: 0 gm/s, Max.: 655.35 gm/s
    2.0 to 4.5 gm/s: Idling
    1. If value approximately 0.0 gm/s:
      1. Mass air flow meter power source circuit open
    2. VG circuit open or short if value 160.0 gm/s or more:
      1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure
    (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    75 to 100°C (167 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data
    Radiator Coolant Temp
    Engine coolant (radiator) temperature/
    Min.: -40°C, Max.: 140°C
    75 to 100°C (167 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position/
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No.1 Volt %
    Absolute Accelerator Pedal Position (APP) No.1/
    Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal released
    52 to 90%: Accelerator pedal fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute APP No.2/
    Min.: 0%, Max.: 100%
    24 to 40%: Accelerator pedal released
    68 to 95%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.1
    APP sensor No.1 voltage/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accel Sensor Out No.2
    APP sensor No.2 voltage/
    Min.: 0 V, Max.: 4.98 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 4.75 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close #1 (AD)
    Accelerator fully closed value No.1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    -
    ETCS service data
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No.1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No.2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Throttle Sensor Volt %
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    -
    Throttle Sensor #2 Volt %
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Throttle fully closed
    2. 92 to 100%: Throttle fully open
    Calculated value based on VTA2
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    10 to 18%: Idling
    Calculated value based on VTA1
    Throttle Position No.1
    Throttle position No.1/
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully open
    -
    Throttle Position No.2
    Throttle position No.2/
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Throttle fully closed
    2. 4.6 to 4.98 V: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No.1/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No.2/
    Min.: 0 V, Max.: 4.98 V
    2.2 to 2.6 V
    ETCS service data
    Throttle Sens Open #1(AD)
    Throttle sensor opener position No.1 (AD)/
    Min.: 0 V, Max.: 4.9 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle actuator control permitted/
    ON or OFF
    ON: Idling
    Read value with ignition switch ON
    (Do not start engine)
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    -
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    -
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 100%
    0 to 40%: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close)/
    Min.: 0%, Max.: 100%
    0 to 40%: Idling
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 0.8 V
    -
    ETCS Actuator Power
    Whether or not electronic throttle control system power input/
    ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 19.9 V
    10 to 15 V: Idling
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data
    Fail Safe Drive
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Throttle Position
    Throttle valve opening angle/
    Min.: 0 deg, Max.: 499.99 deg
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Flow
    Flow rate calculated using information from each sensor/
    Min.: 0 L/s, Max.: 79.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Position
    Requested opening amount calculated using ISC control/
    Min.: 0 deg, Max.: 499.99 deg
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Feedback Value
    ISC feedback compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Learning Value
    ISC learned compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Electric Load Feedback Val
    Compensation flow rate according to electrical load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Air Conditioner FB Val
    Compensation flow rate according to air conditioner load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    PS Feedback Val
    Compensation flow rate according to power steering load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Low Revolution Control
    Low engine speed control operation state/
    ON or OFF
    -
    For use when engine stall, starting problems or rough idle is present.
    N Range Status
    Shift lever N status/
    ON or OFF
    -
    For use when engine stall, starting problems or rough idle is present.
    Eng Stall Control FB Flow
    Intake air compensation flow rate/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Injector (Port)
    Injection period of No.1 cylinder/
    Min.: 0 μs, Max.: 65535 μs
    Min.: 0 ms, Max.: 32.64 ms
    1800 to 3800 μs: Idling
    1.8 to 3.8 ms: Idling
    -
    Injection Volum (Cylinder1)
    Injection volume/
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Fuel Pump/Speed Status
    Fuel pump/speed status/
    ON or OFF
    -
    Active Test support data
    Current Fuel Type
    Status of the current fuel type
    Gasoline/petrol
    -
    EVAP (Purge) VSV
    EVAP (Purge) VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 102.3%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -50, Max.: 349.99
    -40 to 0%: Idling
    Service data
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    -
    Purge Cut VSV Duty
    Purge cut VSV duty/
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Air-fuel ratio/
    Min.: 0, Max.: 1.998
    0.8 to 1.2: Idling
    -
    AF Lambda B1S1
    Air-fuel ratio associated with bank 1 sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    A/F sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    AFS Current B1S1
    A/F sensor output current for bank 1 sensor 1/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the current output of the sensor.
    A/F Heater Duty #1
    A/F heater duty ratio (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    O2S B1S2
    Heated oxygen sensor output voltage for bank 1 sensor 2/
    Min.: 0 V, Max.: 1.275 V
    0 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the voltage output of the sensor.
    O2 Heater B1S2
    Heated oxygen sensor heater for Bank 1 Sensor 2/
    Active or Not Act
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor current for Bank 1 Sensor 2/
    Min.: 0 A, Max.: 4.999 A
    -
    -
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to 20%
    1. Overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
    2. Air fuel ratio feedback leaning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
    A/F Learn Value Idle #1
    Air-fuel ratio learned value for idling (bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
    A/F Learn Value Low #1
    Air-fuel ratio learned value for low engine loads (bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid1 #1
    Air-fuel ratio learned value for mid-sized engine loads 1 (bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid2 #1
    Air-fuel ratio learned value for mid-sized engine loads 2 (bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).
    A/F Learn Value High #1
    Air-fuel ratio learned value for high engine loads (bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
    Total FT #1
    Total fuel trim of bank 1 Average value for fuel trim system of bank 1/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (Bank 1)/
    OL or CL or OLDrive or OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using air-fuel ratio sensor as feedback for fuel control
    3. OLDrive: Open loop due to driving conditions (fuel enrichment)
    4. OLFault: Open loop due to detected system fault
    5. CLFault: Closed loop but air-fuel ratio sensor, which used for fuel control, malfunction
    Fuel System Status #2
    Fuel system status (Bank 2)/
    OL or CL or OLDrive or OLFault or CLFault
    Unused
    Air Pump Pressure (Absolute)
    Air pump pressure (absolute)/
    Min.: 0 kPa, Max.: 65535 kPa
    1. Atmospheric pressure +1 kPa or more: Air pump on, air switching valve open
    2. Close to atmospheric pressure: Air pump off, air switching valve closed
    -
    Air Pump Pulsation Pressure
    Air pump pulsation pressure/
    Min.: 0 kPa, Max.: 655.35 kPa
    -
    Cumulative pulsation pressure calculated by ECM
    Secondary Air Control VSV
    Secondary air injection system status/
    ON or OFF
    ON: Secondary air injection system operating
    -
    2nd Air System Status
    Secondary air system status/
    ON or OFF
    ON: Secondary air injection system operating
    -
    AI Test
    AI operation prohibit/
    READY or NOT RDY
    -
    Active Test support data
    IGN Advance
    Ignition timing advance for No.1 cylinder/
    Min.: -64 deg, Max.: 63.5 deg
    BTDC 4 to 17 deg: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -64 deg(CA), Max.: 1983.9 deg(CA)
    -19 to 0 deg(CA):
    Driving, 70 km/h (44 mph)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -64 deg(CA), Max.: 1983.9 deg(CA)
    0 to 19 deg(CA):
    Driving, 70 km/h (44 mph)
    Service data
    Idle Spark Advn Ctrl #1
    Individual cylinder timing advance compensation amount (No. 1 cylinder)/
    Min.: 0 deg(CA), Max.: 15.93 deg(CA)
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #2
    Individual cylinder timing advance compensation amount (No. 2 cylinder)/
    Min.: 0 deg(CA), Max.: 15.93 deg(CA)
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #3
    Individual cylinder timing advance compensation amount (No. 3 cylinder)/
    Min.: 0 deg(CA), Max.: 15.93 deg(CA)
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #4
    Individual cylinder timing advance compensation amount (No. 4 cylinder)/
    Min.: 0 deg(CA), Max.: 15.93 deg(CA)
    -
    For use when engine stall, starting problems or rough idle is present.
    Actual VVT Angle #1
    VVT displacement angle for bank 1/
    Min.: 0 DegFR, Max.: 639.99 DegFR
    -
    This is only available in Freeze Frame Data.
    VVT Control Status #1
    VVT control status/
    ON or OFF
    -
    -
    VVT Advance Fail
    VVT control failure status/
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1
    VVT aim angle (Bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle #1
    VVT change angle/
    Min.: 0 DegFR, Max.: 60 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty #1
    VVT OCV operation duty/
    Min.: 0%, Max.: 100%
    0%: Idling
    Requested duty value for intrusive operation
    VN Turbo Type
    VN turbo type/
    Not Avl, Commo, Vacuum, CAN Com or DC
    -
    -
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1 sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1 sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Power Steering Signal
    Power steering signal/
    ON or OFF
    ON: Power steering operation
    -
    Power Steer. Sig. Record
    Power steering signal/
    ON or OFF
    ON: When steering wheel first turned after ignition switch turned to ON
    This signal status usually ON until ignition switch turned to OFF
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    A/C Signal
    A/C signal/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Electrical Load Signal
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger turned ON
    -
    Check Mode
    Check mode/
    ON or OFF
    Check mode ON
    Click here
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    AS Test Result
    Check mode result for secondary air injection system/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for HO2 sensor/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for A/F sensor/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor:
    Not Avl or Avail
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor:
    Compl or Incmpl
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status/
    ON or OFF
    -
    -
    # Codes(Include History)
    # Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 min, Max.: 65535 min
    Equivalent to running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min, Max.: 65535 min
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs erased
    -
    Warm up Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    Dist Batt Cable Disconnect
    Distance driven after battery cable disconnected/
    Min.: 0 km, Max.: 65535 km
    Total distance vehicle driven after battery cable disconnected
    -
    IG OFF Elapsed Time
    Time after ignition switch turned off/
    Min.: 0 min, Max.: 655350 min
    Cumulative time after ignition switch turned off
    -
    OBD Requirements
    OBD requirements
    EOBD (Euro OBD) or Not OBD compliant
    -
    Number of Emission DTC
    Number of emission DTCs
    -
    -
    TC and TE1
    TC and TE terminals of DLC3/
    ON or OFF
    -
    Active Test support data
    Total Distance Traveled
    Total distance traveled/
    Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile)
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 800
    0 to 400
    -
    Cylinder #1 Misfire Count
    Misfire count of cylinder 1/
    Min.: 0, Max.: 255
    0
    -
    Cylinder #2 Misfire Count
    Misfire count of cylinder 2/
    Min.: 0, Max.: 255
    0
    -
    Cylinder #3 Misfire Count
    Misfire count of cylinder 3/
    Min.: 0, Max.: 255
    0
    -
    Cylinder #4 Misfire Count
    Misfire count of cylinder 4/
    Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 35
    -
    Misfire RPM
    Engine RPM for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -128%, Max.: 127%
    0 to 99.2%
    Misfire detecting margin.
    Engine Speed (Starter Off)
    Engine speed when starter off/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    For use when engine stall, starting problems or rough idle is present.
    Starter Count
    Number of times starter turned on after ignition switch turned to ON/
    Min.: 0, Max.: 255
    -
    For use when engine stall, starting problems or rough idle is present.
    Run Dist of Previous Trip
    Distance driven during previous trip/
    Min.: 0 km, Max.: 655.35 km
    -
    Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

    HINT:
    Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

    Engine Starting Time
    Time elapsed after engine started (interval between ignition switch ON and off)/
    Min.: 0 ms, Max.: 655350 ms
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Coolant Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Intake Temp
    Intake air temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Engine Oil Temperature
    Engine oil temperature (estimated temperature)/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Eng Oil Temp
    Engine oil temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Ambient Temp for A/C
    Ambient temperature for A/C/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Ambient Temp
    Ambient temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Engine Start Hesitation
    History of hesitation during engine start/
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine start/
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    For use when engine stall, starting problems or rough idle is present.
    Fuel Cut Elps Time
    Time elapsed after engine runs at high speed/
    Min.: 0 sec, Max.: 68746 sec
    -
    -
    Electric Fan Motor
    Electric fan motor status/
    ON or OFF
    -
    Active Test support data
    Brake Override System
    Brake Override System Status/
    ON or OFF
    ON: Brake override system operation
    -
    Idle Fuel Cut
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm
    FC TAU
    Fuel cut TAU (Fuel cut during very light load)/
    ON or OFF
    ON: Fuel cut operation
    Fuel cut initiated under very light load to prevent in complete combustion
    Immobiliser Fuel Cut
    Status of the immobiliser fuel cut/
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of the immobiliser fuel cut history/
    ON or OFF
    -
    -
    Electrical Load Signal 1
    Electrical load signal/
    ON or OFF
    -
    -
    Electrical Load Signal 2
    Electrical load signal/
    ON or OFF
    -
    -
    Electrical Load Signal 3
    Electrical load signal/
    ON or OFF
    -
    -
    Model Code
    Model code
    -
    Identifying model code:
    TRH2###
    Engine Type
    Engine type
    -
    Identifying engine type:
    2TR
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying cylinder number:
    4
    Transmission Type
    Transmission type
    -
    Identifying transmission type:
    MT, ECT
    Destination
    Destination
    -
    Identifying destination:
    W
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying model year:
    20##
    System Identification
    Identification of engine system
    Gasoline (gasoline engine)
    -
    Engine Speed of Cyl #1
    Engine rpm during No. 1 cylinder fuel cut/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Compression Check is performed using Active Test
    Engine Speed of Cyl #2
    Engine rpm during No. 2 cylinder fuel cut/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Compression Check is performed using Active Test
    Engine Speed of Cyl #3
    Engine rpm during No. 3 cylinder fuel cut/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Compression Check is performed using Active Test
    Engine Speed of Cyl #4
    Engine rpm during No. 4 cylinder fuel cut/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Compression Check is performed using Active Test
    Av Engine Speed of All Cyl
    Average of engine rpm values during fuel cut of No. 1 to No. 4 cylinders/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Compression Check is performed using Active Test


ACTIVE TEST

HINT:
Performing an Active Test using the intelligent tester enables components including the relay, VSV, and actuator to be operated without removing any parts. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time.
Data List is displayed during an Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. Perform the Active Test by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All injectors tested at the same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed in 0.1 or 0.2% graduations within control range
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5% / 0% / 12.5%
    1. Perform test at less than 3000 rpm
    2. A/F Control enables to check and graph A/F sensor and heated oxygen sensor voltage outputs
    3. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / User Data / AFS Voltage B1S1 and O2S B1S2
    Activate the VSV for Secondary Air Control
    Activate the secondary Air system
    ON/OFF
    1. Do not perform test for 5 seconds or more.
    2. After test, do not perform test again for 30 seconds.
    Activate the VSV for Evap Control
    Activate EVAP VSV control
    ON/OFF
    The valve is opened with a 30% duty ratio.
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Shift lever in P or N
    Connect the TC and TE1
    Turn ON and OFF TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    Activate cooling fan
    ON/OFF
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Shift lever in P or N
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    ON: throttle valve opens slowly
    1. Test possible when following conditions met:
      1. Ignition switch ON
      2. Engine does not start
      3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    ON: throttle valve opens fast
    Control the VVT Linear (Bank 1)
    Activate OCV
    Min.: -128%, Max.: 127%
    1. Test possible during vehicle stopping and engine idling
    2. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn ON and OFF OCV
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON
    2. Normal engine running or idling when OCV OFF
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the Cylinder#1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling
    Control the Cylinder#2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Control the Cylinder#3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Control the Cylinder#4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Control the All Cylinders Fuel Cut
    All cylinder injectors fuel cut
    ON/OFF
    Check the Cylinder Compression
    All cylinder injectors fuel cut and ignition stop
    ON/OFF
    *

    HINT:
    *: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the tester on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      1. To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
      2. Push the Function button and then select Snapshot Configuration to set the Trigger Point to zero.
      3. Set the Record Time to 30 seconds.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Fully open the throttle.
    10. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    11. Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press the Exit button to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.
      3. Use a fully-charged battery.

      HINT:
      At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    12. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    13. Push the snapshot button to turn the snapshot function off.
    14. Enter the following menus: Function / Snapshot Review / Engine and ECT / Snapshot File Manager, select the recorded data and display the data.

      HINT:
      If the data is not displayed, the change in the values cannot be observed.

    15. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.


SYSTEM CHECK

HINT:
Performing a system check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The system check can be performed with the intelligent tester.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the system check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Notes
    Secondary Air Injection Check
    (Automatic Mode)
    Perform secondary air injection system operation automatically
    With warm engine, ignition switch turned off once
    1. If there are no pending DTCs after performing this test, the system is functioning normally.
    2. Refer to the inspection procedure for secondary air injection system DTCs.
    3. When performing air injection check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    4. Turn the ignition switch off when the system check is finished.
    Secondary Air Injection Check
    (Manual Mode)
    Perform 3 operations in order to operate secondary air injection system monitor manually
    With warm engine, ignition switch turned off once
    1. Used to detect malfunctioning parts.
    2. Refer to the inspection procedure for secondary air injection system DTCs.
    3. When performing the air injection check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    4. Turn the ignition switch off when the system check is finished.

← FAIL-SAFE CHART (from Oct 2014)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →