2014-2019 Hiace · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Oct 2014

A194498E50

HINT:
Each ECM terminal's standard normal voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition". Use the illustration above as a reference for the ECM terminals.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
B74-2 (BATT) - D100-109 (E1)
W - W-B
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B74-6 (SREL) - D100-45 (E01)
G - W-B
GLOW relay
Cranking
11 to 14 V
Idling
(engine start and after 600 second)
0 to 1.5 V
B74-5 (MREL) - D100-109 (E1)
Y - W-B
EFI MAIN relay
Ignition switch ON
11 to 14 V
Ignition switch off
(after ignition switch off for 2 second)
0 to 1.5 V
B74-40 (TC) - D100-109 (E1)
G - W-B
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
D100-48 (RFC) - D100-109 (E1)
LG - W-B
Cooling fan motor
Ignition switch ON or fan is rotating
Pulse generation
(See waveform 1)
B74-41 (SPD) - D100-109 (E1)
P - W-B
Speed signal from combination meter assembly
Ignition switch ON, rotate driving wheel slowly
Pulse generation
(See waveform 2)
B74-33 (STA) - D100-109 (E1)
R - W-B
Starter signal
Cranking
6 V or more
B74-1 (+B) - D100-109 (E1)
L - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
B74-25 (IGSW) - D100-109 (E1)
B - W-B
Ignition switch
Ignition switch ON
11 to 14 V
B74-27 (STP) - D100-109 (E1)
Y - W-B
Stop light switch assembly
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1.5 V
B74-48 (HSW) - D100-109 (E1)
L - W-B
Idle up switch
Idle up switch ON
Below 2.5 V
Idle up switch OFF
11 to 14 V
D100-58 (ALT) - D100-109 (E1)
W - W-B
Generator (alternator) duty ratio
Idling
Pulse generation
(See waveform 3)
B74-47 (AC1) - D100-109 (E1)
B - W-B
Air conditioning amplifier assembly
A/C switch ON
(at magnet clutch ON)
1.3 to 2.6 V
A/C switch OFF
3.7 to 4.5 V
B74-60 (VPA) - B74-59 (EPA)
L - W
Accelerator pedal position sensor
(for engine control)
Ignition switch ON, accelerator pedal released
0.5 to 1.1 V
Ignition switch ON, accelerator pedal depressed
2.6 to 4.5 V
B74-58 (VCPA) - B74-59 (EPA)
W - W
Power source of accelerator pedal position sensor
(for VPA)
Ignition switch ON
4.5 to 5.5 V
B74-55 (VPA2) - B74-56 (EPA2)
B - Y
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal released
1.2 to 2.0 V
Ignition switch ON, accelerator pedal depressed
3.4 to 5.0 V
B74-57 (VCP2) - B74-56 (EPA2)
L - Y
Power source of accelerator pedal position sensor
(for VPA2)
Ignition switch ON
4.5 to 5.5 V
B74-17 (TACH) - D100-109 (E1)
B - W-B
Engine speed
Idling
Pulse generation
(See waveform 4)
B74-15 (ACT) - D100-109 (E1)
G - W-B
Air conditioning amplifier assembly
A/C switch ON
(at magnet clutch ON)
11 to 14 V
A/C switch OFF
Below 1.0 V
B74-26 (ST1-) - D100-109 (E1)
R - W-B
Stop light switch assembly
Brake pedal depressed
Below 1.5 V
Brake pedal released
11 to 14 V
D100-96 (VCPM) - D100-92 (EPIM)
L - Y
Power source of manifold absolute pressure sensor
Ignition switch ON
4.5 to 5.5 V
D100-69 (PIM) - D100-92 (EPIM)
P - Y
Manifold absolute pressure sensor
Apply vacuum 60 kPa
(450 mmHg, 17.7 in.Hg)
0.2 to 0.8 V
Apply vacuum 207 kPa
(1,550 mmHg, 61.0 in.Hg)
4.2 to 4.8 V
D100-71 (THA) - D100-94 (ETHA)
L - Y
Intake air temperature sensor
Idling, air intake temp. 0°C (32°F) to 80°C (176°F)
0.5 to 3.4 V
D100-70 (THW) - D100-93 (ETHW)
R-W - Y-R
Engine coolant temperature sensor
Idling, engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
D100-72 (THF) - D100-95 (ETHF)
R - Y
Fuel temperature sensor
Ignition switch ON (at engine cold)
0.5 to 3.4 V
D100-118 (DATA) - D100-109 (E1)
Y - W-B
Injection pump correction unit
For 0.5 sec. after ignition switch ON
Pulse generation
D100-56 (PR2) - D100-109 (E1)
Y - W-B
Pressure switch
Pressure switch ON (A/C pressure is normal)
Below 1.5 V
Pressure switch OFF (A/C pressure is low)
11 to 14 V
D100-68 (RTHW) - D100-91 (EPEX)
L - Y
Radiator side engine coolant temperature sensor
Idling, radiator side engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
D100-119 (CLK) - D100-109 (E1)
L - W-B
Injection pump correction unit
For 0.5 second after ignition switch ON
Pulse generation
D100-57 (THOP) - D100-109 (E1)
L - W-B
Throttle open switch
Idling (engine warmed up)
11 to 14 V
Ignition switch ON (once within 5 second)
0 to 3 V
D100-43 (LU-B) - D100-45 (E01)
G - W-B
Throttle control motor
Racing (engine warmed up)
Pulse generation
(See waveform 5)
D100-84 (LU+B) - D100-45 (E01)
R - W-B
Throttle control motor
Racing (engine warmed up)
Pulse generation
(See waveform 5)
D100-85 (LU-A) - D100-45 (E01)
W - W-B
Throttle control motor
Racing (engine warmed up)
Pulse generation
(See waveform 5)
D100-46 (LU+A) - D100-45 (E01)
B - W-B
Throttle control motor
Racing (engine warmed up)
Pulse generation
(See waveform 5)
D100-42 (TCV) - D100-45 (E01)
R - W-B
Timing control valve
Ignition switch ON
11 to 14 V
Idling
Pulse generation
D100-82 (SPV+) - D100-109 (E1)
Y - W-B
Spill control valve
Idling
Pulse generation
D100-103 (TDC+) - D100-126 (TDC-)
R - G
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
D100-102 (NE+) - D100-125 (NE-)
B - W
Engine speed sensor
Idling
Pulse generation
(See waveform 6)
D100-41 (SPV-) - D100-109 (E1)
L - W-B
Spill control valve
Idling
Pulse generation
B74-10 (CANH) - D100-109 (E1)
B - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 7)
B74-11 (CANL) - D100-109 (E1)
W - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 8)


Waveform 1 (Reference):

  1. A111767E03
    Cooling fan signal.
    Terminal
    RFC - E1
    Tool Setting
    1 V/DIV., 2 msec./DIV.
    Condition
    When fan operating

    HINT:
    Waveform time A changes according to coolant temperature.


Waveform 2 (Reference):

  1. A110545E06
    Speed signal.
    Terminal
    SPD - E1
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    When driving at approx. 20 km/h (12.4 mph).

    HINT:
    1. As vehicle speed increases, the wavelength becomes shorter.
    2. As vehicle speed increases, the waveform's amplitude becomes greater.


Waveform 3 (Reference):

  1. A105102E02
    Generator signal.
    Terminal
    ALT - E1
    Tool Setting
    5 V/DIV., 5 msec./DIV.
    Condition
    During idling


Waveform 4 (Reference):

  1. A110546E10
    Engine speed signal.
    Terminal
    TACH - E1
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    1. After warming up
    2. During idling

    HINT:
    As engine speed increases, the wavelength becomes shorter.


Waveform 5 (Reference):

  1. A110547E04
    Throttle control motor signal.
    Terminal
    LU+A, LU-A, LU+B, LU-B - E01
    Tool Setting
    10 V/DIV., 0.5 msec./DIV.
    Condition
    During engine racing


Waveform 6 (Reference):

  1. A002483E01
    Crankshaft position sensor signal and Engine speed sensor signal.
    Terminal
    TDC+ - TDC-
    NE+ - NE-
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    During idling


Waveform 7 (Reference):

  1. G036660E02
    CAN communication signal
    Terminal
    CANH - E1
    Tool Setting
    1 V/DIV., 10 msec./DIV.
    Condition
    Engine is stopped, ignition switch ON

    HINT:
    The wavelength becomes shorter as the CAN communication signal


Waveform 8 (Reference):

  1. G036661E02
    CAN communication signal
    Terminal
    CANL - E1
    Tool Setting
    1 V/DIV., 10 msec./DIV.
    Condition
    Engine is stopped, ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.

← PROBLEM SYMPTOMS TABLE (from Jan 2015)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →