DATA LIST / ACTIVE TEST
System information · Vehicles built from Oct 2014
| DATA LIST |
- HINT:
- By reading the Data List displayed on the GTS, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.
- NOTICE:
- In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Check the values by referring to the following table.
Normal Condition: If no idling conditions are specified, the shift lever should be in neutral, and the A/C switch and all accessory switches should be off.Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Notes
Vehicle Speed
Vehicle speed:
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed:
Min.: 0 rpm, Max.: 16383.75 rpm
720 to 820 rpm: Idling (A/C off)
After warming up engine
-
MAP
Absolute pressure inside intake manifold:
Min.: 0 kPa, Max.: 255 kPa
- 90 to 105 kPa: Idling
- 88 to 103 kPa:
Engine running at 2,000 rpm
- 85 to 100 kPa:
Engine running at 3,000 rpm
-
Coolant Temp
Engine coolant temperature:
Min.: -40°C, Max.: 215°C
80 to 95°C (176 to 203°F):
After warming up engine
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air
Intake air temperature:
Min.: -40°C, Max.: 215°C
Equivalent to temperature at intake manifold
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Engine Run Time
Engine run time:
Min.: 0 sec., Max.: 65535 sec.
Time after the ignition switch turned to ON
Time passed since the ignition switch was turned to ON.
Battery Voltage
Battery voltage:
Min.: 0 V, Max.: 65.5 V
11 to 14 V
-
Glow Indicator Supported
Status of the glow indicator supported:
Unsupp or Supp
Supp
-
Glow Indicator
Status of the glow indicator:
ON or OFF
-
-
Accel Position
Accelerator pedal position:
Min.: 0%, Max.: 100%
- Accelerator pedal released:
0%
- Accelerator pedal fully depressed:
100%
-
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position No. 1:
Min.: 0%, Max.: 100%
- Accelerator pedal released:
10 to 22%
- Accelerator pedal fully depressed:
52 to 90%
Read value with ignition switch ON (Do not start engine)
Accel Sens. No.2 Volt %
Absolute Accelerator Pedal Position No. 2:
Min.: 0%, Max.: 100%
- Accelerator pedal released:
24 to 40%
- Accelerator pedal fully depressed:
68 to 95%
Read value with ignition switch ON (Do not start engine)
Diesel Throttle Learn Status
Diesel throttle learning history:
OK or NG
OK
-
Throttle Step Position
Throttle step position:
Min.: 0 step, Max.: 255 step
- 209 step: Throttle valve fully closed
- 0 step: Throttle valve fully open
Read value with ignition switch ON (Do not start engine)
Injection Volume
Injection volume:
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
3 to 11 mm3/st: Idling
-
Inj. FB Vol. for Idle
Idle stability status integral control volume:
Min.: -80 mm3/st, Max.: 79 mm3/st
-
-
Injection Timing
Injection timing:
Min.: 0°CA, Max.: 51°CA
-
-
Fuel Temperature
Fuel temperature:
Min.: -40°C, Max.: 215°C
Actual fuel temperature
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Starter Signal
Starter signal:
ON or OFF
ON: Cranking
-
Stop Light Switch
Stop light switch:
ON or OFF
- ON: Brake pedal depressed
- OFF: Brake pedal released
-
A/C Signal
A/C signal:
ON or OFF
ON: A/C switch is turned ON
-
Throttle Open Switch
Throttle open switch:
ON or OFF
ON: Throttle valve fully open
-
Check Mode
Check mode:
ON or OFF
ON: Check mode ON
Click here
SPD Test Result
Check mode result for vehicle speed sensor:
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor:
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor:
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor:
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor:
Compl or Incmpl
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor:
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS) monitor:
Compl or Incmpl
-
-
A/C Monitor
A/C monitor:
Not Avl or Avail
-
-
A/C Monitor
A/C monitor:
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor:
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor:
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor:
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor:
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor:
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor:
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor:
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor:
Compl or Incmpl
-
-
# Codes (Include History)
Number of codes:
Min.: 0, Max.: 255
0
This is the number of DTCs stored.
MIL
MIL status:
ON or OFF
OFF
-
Time after DTC Cleared
Time after DTCs cleared:
Min.: 0 minutes, Max.: 65535 minutes
Time after DTCs cleared
Time elapsed since the DTCs were cleared (or shipment from the factory).
Distance from DTC Cleared
Distance driven after DTCs cleared:
Min.: 0 km, Max.: 65535 km
Distance driven after DTCs cleared
- Distance driven since the DTCs were cleared.
- (Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred.
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared:
Min.: 0, Max.: 255
-
- Number of engine warmup cycles since DTCs were cleared.
- (Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred.
OBD Requirements
Identifying OBD requirement
-
-
Number of Emission DTC
Number of emissions-related DTCs
-
-
TC and TE1
TC and TE1 connection status for Active Test:
ON or OFF
-
When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected.
ACT VSV
A/C cut status:
ON or OFF
-
"Control the A/C Cut Signal" Active Test support data.
Electric Fan Motor
Electric fan motor:
ON or OFF
ON: Electric fan motor operation
-
Model Code
Model code
-
Identifying model code
Engine Type
Engine type
-
Identifying engine type: 5LE
Cylinder Number
Cylinder number:
Min.: 0, Max.: 255
-
Identifying cylinder number: 4
Transmission Type
Transmission type
-
-
Destination
Destination
-
Identifying destination
Model Year
Model year:
Min.: 1900, Max.: 2155
-
Identifying model year: 20##
System Identification
System identification
-
Identifying engine type: Diesel
- 90 to 105 kPa: Idling
| ACTIVE TEST |
- HINT:
- Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with the GTS. Active Test as a first step of troubleshooting is one method of shortening diagnostic time.
- The Data List can be displayed during Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Tests by referring to the following table.
Tester Display
Test Part
Control Range
Diagnostic Notes
Control the A/C cut signal
Control the A/C cut signal
ON/OFF
Test is possible when the following conditions are met: - Ignition switch ON
- Engine is stopped.
- Shift lever in neutral
Connect the TC and TE1
Turn on the TC and TE1 connection
ON/OFF
Test is possible when the following conditions are met: - Ignition switch ON
- Shift lever in neutral
Control the Electric Cooling Fan
Control the cooling fan operation
ON/OFF
Test is possible when the following conditions are met: - Ignition switch ON
- Engine is stopped.
- Shift lever in neutral
- Ignition switch ON