2014-2019 Hiace · Service Manual TRANSMISSION

TERMINALS OF ECM

System information · Vehicles built Oct 2014 – Dec 2014


CHECK ECM
C176147E32

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
B71-25 (NSW) - D97-105 (E1)
B - W-B
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P or N
Below 1 V
D97-17 (P) - D97-105 (E1)
W - W-B
P shift position switch signal
  1. Ignition switch ON
  2. Shift lever in P
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P
Below 1 V
D97-76 (R) - D97-105 (E1)
L - W-B
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
D97-99 (N) - D97-105 (E1)
GR - W-B
N shift position switch signal
  1. Ignition switch ON
  2. Shift lever in N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in N
Below 1 V
B71-47 (D) - D97-105 (E1)
R - W-B
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D or 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D or 3
Below 1 V
D97-79 (3) - D97-105 (E1)
B - W-B
3 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 3
Below 1 V
D97-78 (2) - D97-105 (E1)
Y - W-B
2 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V
D97-39 (L) - D97-105 (E1)
R - W-B
L shift position switch signal
  1. Ignition switch ON
  2. Shift lever in L
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in L
Below 1 V
D97-56 (S1) - D97-105 (E1)
LG - W-B
S1 solenoid signal
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
D97-55 (S2) - D97-105 (E1)
P - W-B
S2 solenoid signal
2nd or 3rd gear
11 to 14 V
1st or 4th gear
Below 1 V
D97-54 (SLT+) - D97-53 (SLT-)
L - W
SLT solenoid signal
Engine idling
Pulse generation
D97-61 (SL) - D97-105 (E1)
GR - W-B
SL solenoid signal
Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)
Pulse generation
(See waveform 1)
D97-114 (THOC) - D97-72 (E2)
B - Y
ATF temperature sensor signal
ATF temperature: 115°C (239°F) or higher
Below 1.5 V
D97-125 (SP2+) - D97-101 (SP2-)
G - R
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 2)
D97-122 (NC0+) - D97-100 (NC0-)
Y - L
Speed sensor NC0 signal
Engine idling
Pulse generation
(See waveform 3)

  1. C229118E02
    Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    D97-61 (SL) - D97-105 (E1)
    10 V/DIV., 100 msec./DIV.
    Vehicle speed 65 km/h (40 mph), lock-up (ON to OFF)

  2. C229119E01
    Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    D97-125 (SP2+) - D97-101 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)

  3. C229120E01
    Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    D97-122 (NC0+) - D97-100 (NC0-)
    1 V/DIV., 2 msec./DIV.
    Engine idling

← PROBLEM SYMPTOMS TABLE (Oct 2014 – Dec 2014)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →