2014-2019 Hiace · Service Manual TRANSMISSION

P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Also covers:

DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the ATF temperature into a resistance value which is input into the ECM.
The ECM applies a voltage to the temperature sensor through ECM terminal THOC.
The sensor resistance changes with the ATF temperature.
One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature becomes higher.
The ECM calculates the ATF temperature based on the voltage signal.
DTC Code
DTC Detection Condition
Trouble Area
P0712
ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
  1. Short in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM
P0713
When 15 minutes or more have elapsed after the engine is started, ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more (1-trip detection logic).
  1. Open in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature sensor is below 79 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ATF temperature warning light blinks and the ECM stores the DTC.

HINT:
  1. *1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the intelligent tester display.


WIRING DIAGRAM

C294506E04

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 3
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature when engine cold
    If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P0712 is output and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P0713 is output and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit


1. INSPECT ATF TEMPERATURE SENSOR

  1. C238274E02
    Disconnect the ATF temperature sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    79 Ω to 156 kΩ
    1 - Body ground
    Always
    10 kΩ or higher
    2 - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    20°C (68°F)
    10.3 to 13.9 kΩ
    120°C (248°F)
    0.58 to 0.65 kΩ

Text in Illustration 
*a
Component without harness connected
(ATF Temperature Sensor)


NG
REPLACE ATF TEMPERATURE SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - ECM)

  1. C302055E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D97-114 (THOC) - D97-72 (E2)
    Always
    79 Ω to 156 kΩ
    D97-114 (THOC) - Body ground
    Always
    10 kΩ or higher
    D97-72 (E2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) (Oct 2014 – Dec 2014)P0717 Turbine Speed Sensor Circuit No Signal (Oct 2014 – Dec 2014) →