2014-2019 Hiace · Service Manual ENGINE

P00B3 Radiator Coolant Temperature Sensor Circuit Low

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

A thermistor is built into the engine coolant temperature (radiator) sensor, of which the resistance value varies according to the radiator side engine coolant temperature.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
When either DTC P00B3 or P00B4 is set, the ECM enters fail-safe mode. During fail-safe mode, the radiator side engine coolant temperature is estimated to be 80°C (176°F) by the ECM and the radiator fan motors are operated until the pass condition is detected. Fail-safe mode continues until a pass condition is detected.

P00B3 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds or more
Short in engine coolant temperature (radiator) sensor circuit for 3 seconds
(1 trip detection logic)
  1. Short in engine coolant temperature (radiator) sensor circuit
  2. Engine coolant temperature (radiator) sensor
  3. ECM
P00B4 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds or more
Open in engine coolant temperature (radiator) sensor circuit for 3 seconds
(1 trip detection logic)
  1. Open in engine coolant temperature (radiator) sensor circuit
  2. Engine coolant temperature (radiator) sensor
  3. ECM
Related Data List 
DTC No.
Data List
P00B3
Radiator Coolant Temp
P00B4

HINT:
When either of these DTCs are set, check the engine coolant temperature (radiator) by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Radiator Coolant Temp.

Temperature Displayed
Malfunctions
-40°C (-40°F)
Open circuit
140°C (284°F)
Short circuit

MONITOR DESCRIPTION

The engine coolant temperature (radiator) sensor is used to monitor the radiator side engine coolant temperature. The engine coolant temperature (radiator) sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the radiator side engine coolant temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature (radiator) sensor and sets a DTC.
Example:
If the sensor voltage output is -40°C (-40°F) for 0.5 seconds or more, the ECM determines that there is an open in the engine coolant temperature (radiator) sensor circuit, and sets DTC P00B4. Conversely, if the voltage output is 140°C (284°F) for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P00B3.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

WIRING DIAGRAM

A111657E15

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (RADIATOR COOLANT TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Radiator Coolant Temp.

  1. Read the value.

    Standard:
    Between 80°C and 97°C (176°F and 207°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F)
    B
    Between 80°C and 97°C (176°F and 207°F)
    C

    HINT:
    1. If there is an open circuit, the GTS indicates -40°C (-40°F).
    2. If there is a short circuit, the GTS indicates 140°C (284°F).



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING GTS (CHECK FOR OPEN HARNESS)
  1. Confirm good connection of the connector to the ECM.

  1. A109992E04
    Disconnect the engine coolant temperature (radiator) sensor connector.

  1. Connect terminals 1 and 2 of the engine coolant temperature (radiator) sensor connector on the wire harness side.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Radiator Coolant Temp.

  1. Read the value.

    Standard:
    140°C (284°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature (Radiator) Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Engine Coolant Temperature [Radiator] Sensor)

  1. Reconnect the engine coolant temperature (radiator) sensor connector.



OK
Go to step 7

NG
Go to step 3
3. READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
  1. Disconnect the engine coolant temperature (radiator) sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B29-2 - B72-59 (RTHW)
    Always
    Below 1 Ω
    B29-1 -D98-74 (E2)
    Always
    Below 1 Ω

  1. Reconnect the engine coolant temperature (radiator) sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING GTS (CHECK FOR SHORT IN HARNESS)

  1. A198733E14
    Disconnect the engine coolant temperature (radiator) sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Radiator Coolant Temp.

  1. Read the value.

    Standard:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature (Radiator) Sensor
    *2
    ECM

  1. Reconnect the engine coolant temperature (radiator) sensor connector.



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE [RADIATOR] SENSOR - ECM)
  1. Disconnect the ECM connectors.

  1. Disconnect the engine coolant temperature (radiator) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B72-59 (RTHW) or B29-2 - Body ground
    Always
    10 kΩ or higher
    D98-74 (E2) or B29-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the engine coolant temperature (radiator) sensor connector.



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE (RADIATOR) SENSOR.
  1. Replace the engine coolant temperature (radiator) sensor (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE ENGINE COOLANT TEMPERATURE (RADIATOR) SENSOR
  1. Replace the engine coolant temperature (radiator) sensor (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P00B3 Radiator Coolant Temperature Sensor Circuit Low (+ P00B4) (Apr 2016 – Dec 2016)P0101 Mass Air Flow Circuit Range / Performance Problem (Oct 2014 – Dec 2014) →