INSTALLATION
Removal / installation · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
| 1.
INSTALL NO. 1 ROOF HEADLINING (w/o Rear Air Conditioning System) |
 |
Attach the clip A to install the No. 1 roof headlining.
Install the 6 clips.
| 2.
INSTALL NO. 1 ROOF HEADLINING (w/ Rear Air Conditioning System) |
 |
Attach the clip A to install the No. 1 roof headlining.
Install the 10 clips and 4 screws.
| 3.
INSTALL REAR COOLER CONTROL PANEL (w/ Rear Air Conditioning System)
|
 |
Install the connector.
- Engage the 4 clips and 4 claws to install the rear cooler control panel.
| 4.
INSTALL VISOR HOLDER |
 |
- HINT:
- Use the same procedure described for the other side.
Attach the claw to install the visor holder.
Install the screw.
| 5.
INSTALL VISOR ASSEMBLY LH |
 |
Install the visor assembly LH with the 2 screws.
| 6.
INSTALL VISOR ASSEMBLY RH |
 |
- HINT:
- Use the same procedure described for the LH side.
| 7.
INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
 |
Connect the connector.
Install the No. 1 room light assembly with the 2 screws.
Attach the 4 claws to install the light cover.
| 8.
INSTALL BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Rear Air Conditioning System)
|
 |
- HINT:
- Use the same procedure for all back window glass hammers.
Connect the connector.
Attach the 2 guides and claw to install the back window glass hammer.
Install the 2 bolts.
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}


Text in Illustration
*A
|
for Super Long Wheelbase
|
*B
|
for Long Wheelbase
|
| 9.
INSTALL CENTER PILLAR GARNISH RH (w/ Rear Air Conditioning System) |
|
| 10.
INSTALL CENTER PILLAR GARNISH LOWER RH (w/ Rear Air Conditioning System) |
|
| 11.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (w/ Rear Air Conditioning System)
|
 |
- Connect the front seat outer belt assembly RH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 2 claws to close the cover.
- Connect the front seat outer belt assembly RH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 12.
INSTALL SLIDE DOOR WEATHERSTRIP NO. 1 RH (w/ Rear Air Conditioning System) |
|
| 13.
INSTALL REAR DOOR SCUFF PLATE RH (w/ Rear Air Conditioning System) |
|
| 14.
INSTALL CENTER PILLAR GARNISH LH (w/ Rear Air Conditioning System) |
|
| 15.
INSTALL ENGINE SERVICE HOLE COVER HOOK NO. 2 LH (w/ Rear Air Conditioning System) |
|
| 16.
INSTALL CENTER PILLAR GARNISH LOWER LH (w/ Rear Air Conditioning System) |
|
| 17.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear Air Conditioning System)
|
 |
- Connect the front seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 2 claws to close the cover.
- Connect the front seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 18.
INSTALL SEAT BELT ANCHOR COVER (w/ Rear Air Conditioning System) |
|
| 19.
INSTALL SEAT ASSEMBLY LH (w/ Rear Air Conditioning System) |
|
| 20.
INSTALL CENTER PILLAR GARNISH COVER LOWER LH (w/ Rear Air Conditioning System) |
|
| 21.
INSTALL ASSIST GRIP (w/o Rear Air Conditioning System) |
 |
Install the assist grip with the 2 screws.
Attach the 6 claws to close the 2 assist grip covers.
| 22.
CONNECT REAR NO. 3 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System) |
 |
- Tighten the bolt to connect the shoulder side of the rear No. 3 seat belt assembly outer.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 4 claws to close the shoulder side cover of the rear No. 3 seat belt assembly outer.
| 23.
INSTALL FRONT PILLAR GARNISH RH |
 |
Attach the 2 claws and clip to install the front pillar garnish RH.
| 24.
INSTALL FRONT PILLAR GARNISH LH |
 |
- HINT:
- Use the same procedure described for the RH side.
| 25.
INSTALL ASSIST GRIP ASSEMBLY |
 |
Install the assist grip assembly with the 2 screws.
- HINT:
- Use the same procedure described for the other side.
| 26.
INSTALL ASSIST GRIP PLUG |
 |
Attach the 4 claws to install the 2 assist grip plugs.
| 27.
INSTALL FRONT DOOR OPENING TRIM RH |
|
| 28.
INSTALL FRONT DOOR OPENING TRIM LH |
|
| 29.
INSTALL FRONT DOOR SCUFF PLATE LH |
 |
Attach the 5 clips to install the front door scuff plate LH.
| 30.
INSTALL FRONT DOOR SCUFF PLATE RH |
 |
Attach the 5 clips to install the front door scuff plate RH.
| 31.
INSTALL NO. 2 ROOF HEADLINING (w/o Rear Air Conditioning System) |
 |
Install the No. 2 roof headlining with the 5 clips.
| 32.
INSTALL NO. 2 ROOF HEADLINING (w/ Rear Air Conditioning System) |
 |
Attach the 4 clips A to install the No. 2 roof headlining.
Install the 18 clips.
| 33.
INSTALL NO. 3 ROOF HEADLINING (w/o Rear Air Conditioning System) |
 |
Install the No. 3 roof headlining with the 3 clips.
| 34.
INSTALL NO. 4 ROOF HEADLINING (w/o Rear Air Conditioning System) |
 |
Install the No. 4 roof headlining with the 17 clips.
| 35.
INSTALL ROOF CLIP (w/o Rear Air Conditioning System) |
 |
Attach the 2 claws to install the roof clip.
| 36.
INSTALL REAR ROOF HEADLINING GARNISH (w/o Rear Air Conditioning System) |
 |
Attach the 18 clips to install the rear roof headlining garnish.
| 37.
INSTALL REAR ROOF HEADLINING GARNISH (w/ Rear Air Conditioning System) |
 |
Attach the 18 clips to install the rear roof headlining garnish.
| 38.
INSTALL ROOF HEADLINING MOULDING (w/o Rear Air Conditioning System) |
 |
Attach the 18 clips to install the 2 roof headlining mouldings.
| 39.
CONNECT REAR NO. 4 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System) |
 |
- HINT:
- Use the same procedure described for the other side.
- Tighten the bolt to connect the shoulder side of the rear seat belt assembly outer.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- Attach the 4 claws to close the shoulder side cover of the rear seat belt assembly outer.
| 40.
INSTALL BACK DOOR WEATHERSTRIP (w/ Rear Air Conditioning System) |
|
| 41.
INSTALL BACK DOOR SCUFF PLATE (w/ Rear Air Conditioning System) |
|
| 42.
INSTALL NO. 2 ROOM LIGHT ASSEMBLY |
 |
- HINT:
- Use the same procedure described for the other side.
Connect the connector.
Install the No. 2 room light assembly with the 2 screws.
Attach the 4 claws to install the light cover.
| 43.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
 |
-
Torque:
- 5.4 N*m{
55 kgf*cm
, 48 in.*lbf
}
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).