REASSEMBLY
Removal / installation · Vehicles built Oct 2014 – Dec 2016
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
| 1.
INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY |
 |
- Install the No. 1 seat leg sub-assembly with the 4 bolts.
-
Torque:
- 55 N*m{
561 kgf*cm
, 41 ft.*lbf
}
| 2.
INSTALL WARNING REFLECTOR HOLDER ASSEMBLY |
 |
- Install the 4 warning reflector holder assemblies with the 4 screws.
| 3.
INSTALL REAR SEAT CUSHION UNDER COVER |
 |
- Install the rear seat cushion under cover with the 11 screws.
| 4.
INSTALL SEAT TRACK ADJUSTING HANDLE KNOB |
 |
- Install the seat track adjusting handle knob with the 2 screws.
| 5.
INSTALL NO. 1 SEAT REAR LEG SUB-ASSEMBLY |
|
| 6.
INSTALL REAR SEAT CUSHION HINGE LOWER COVER |
|
| 7.
INSTALL REAR SEAT LEG STOPPER |
|
| 8.
INSTALL NO. 1 SEAT LEG STOPPER HOLDER |
|
| 9.
INSTALL REAR NO. 1 SEAT LOCK ASSEMBLY |
 |
- Install the 2 rear No. 1 seat lock assemblies with the 4 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 10.
INSTALL REAR SEAT INNER BELT ASSEMBLY
|
 |
- HINT:
- Follow the same procedure as for the fixed seat type.
| 11.
INSTALL REAR SEAT OUTER BELT ASSEMBLY
|
 |
- HINT:
- Follow the same procedure as for the fixed seat type.
| 12.
INSTALL REAR SEAT LOCK ROD |
 |
- Install the rear seat lock rod with the 2 nuts.
-
Torque:
- 8.0 N*m{
82 kgf*cm
, 71 in.*lbf
}
| 13.
INSTALL REAR SEAT BACK LOCK COVER |
 |
- Install the 2 rear seat back lock covers with the 4 screws.
| 14.
INSTALL RECLINING ADJUSTER RELEASE HANDLE |
 |
- Install the 2 reclining adjuster release handles with the 2 screws.
| 15.
INSTALL NO. 1 SEAT LEG LOWER BRACKET |
 |
- Install the 2 No. 1 seat leg lower brackets with the 2 bolts.
-
Torque:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
| 16.
INSTALL REAR SEAT LEG SIDE COVER |
 |
- Install the 2 rear seat leg side covers with the 2 screws.
| 17.
INSTALL NO. 1 SEAT BACK SPRING ASSEMBLY |
 |
- Install the No. 1 seat back spring assembly with the 4 bolts.
-
Torque:
- 55 N*m{
561 kgf*cm
, 41 ft.*lbf
}
| 18.
INSTALL REAR SEAT NO. 1 RECLINING COVER LH |
 |
- Install the rear seat No. 1 reclining cover LH with the screw.
| 19.
INSTALL REAR SEAT NO. 1 RECLINING COVER RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 20.
INSTALL REAR SEAT CUSHION NO. 1 SHIELD INNER LH |
 |
- Engage the claw and install the rear seat cushion No. 1 shield inner LH.
Install the screw.
| 21.
INSTALL REAR SEAT CUSHION NO. 1 SHIELD INNER RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 22.
INSTALL NO. 1 SEAT BACK COVER SUB-ASSEMBLY |
 |
- Using hog ring pliers, install the No. 1 seat back cover sub-assembly to the No. 1 seat back pad with 6 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 23.
INSTALL NO. 1 SEAT BACK COVER WITH PAD SUB-ASSEMBLY |
 |
Install the No. 1 seat back cover with pad sub-assembly.
- Operate the reclining release handle sub-assembly and fold down the seat back onto the seat cushion.
- Using hog ring pliers, install the No. 1 seat back cover with pad sub-assembly with 6 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Close the fastener of the No. 1 seat back cover sub-assembly.
Operate the reclining release handle sub-assembly and return the seat back to the upright position.
| 24.
INSTALL REAR SEAT HEADREST SUPPORT |
 |
- Engage the 8 claws and install the 4 rear seat headrest supports.
| 25.
INSTALL REAR SEAT HEADREST ASSEMBLY |
 |
- Push the lock button of the rear seat headrest support and install the rear seat headrest.
| 26.
INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY |
 |
- Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad with 14 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 27.
INSTALL NO. 1 SEAT CUSHION COVER WITH PAD SUB-ASSEMBLY |
|
| 28.
INSTALL REAR SEAT NO. 2 RECLINING COVER LH |
 |
- Engage the 6 claws and install the rear seat No. 2 reclining cover LH.
| 29.
INSTALL REAR SEAT NO. 2 RECLINING COVER RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 30.
INSTALL REAR SEAT BACK COVER LH |
 |
- Install the rear seat back cover LH.
| 31.
INSTALL REAR SEAT BACK COVER RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 32.
INSTALL RECLINING ADJUSTER COVER LH |
 |
- Engage the claw and clip and install the reclining adjuster cover LH.
Install the 2 screws.
| 33.
INSTALL RECLINING ADJUSTER COVER RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 34.
INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH |
 |
- Engage the claw and install the No. 1 reclining adjuster release handle LH.
| 35.
INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH |
 |
- HINT:
- Use the same procedures for the RH side and LH side.
| 36.
INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY |
 |
- Install the reclining release handle sub-assembly and the snap ring.