2014-2019 Hiace · Service Manual STEERING

REASSEMBLY

Removal / installation · Vehicles built from Oct 2014

NOTICE:
When installing, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat a new vane pump housing oil seal lip with power steering fluid.

  1. C101980E01
    Using SST and a press, install the vane pump housing oil seal to the front vane pump housing.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the vane pump housing oil seal is installed in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT BEARING

  1. C101975
    Using a snap ring expander, install the vane pump shaft snap ring to the vane pump shaft.

  1. Wrap the serration of the vane pump shaft with protective tape.

  1. C101981E01
    Using a press, install the vane pump shaft to the new vane pump shaft bearing.

    CAUTION:
    1. Do not damage the vane pump shaft bearing.
    2. Make sure that the vane pump shaft bearing inner race sits on the V-blocks.


3. INSTALL VANE PUMP GEAR

  1. C102432E01
    Using SST and a press, install the vane pump shaft to the vane pump gear.
    SST
    09950-60010   (09951-00250)

    HINT:
    Press on the vane pump shaft until the end faces of the shaft and vane pump gear become level.

  1. C102433E01
    Using SST and a press, install the vane pump shaft to the front vane pump housing.
    SST
    09950-60010   (09951-00250)

    HINT:
    Press on the vane pump shaft until the snap ring groove of the front vane pump housing can be seen.

  1. Install snap ring to the front vane pump housing.


4. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C101970
    Coat a new O-ring with power steering fluid and install it into the front vane pump housing.

  1. C101969
    Coat a new O-ring with power steering fluid and install it onto the front vane pump side plate.

  1. C101385
    Align the dent of the front vane pump side plate with that of the front vane pump housing, and install the front vane pump side plate.

    NOTICE:
    Make sure that the front vane pump side plate is installed in the correct direction as shown in the illustration.


5. INSTALL VANE PUMP CAM RING

  1. C101386E01
    Align the dent of the vane pump cam ring with that of the front vane pump side plate, and install the vane pump cam ring with the inscribed mark facing upward.

    NOTICE:
    Make sure that the cam ring is installed in the correct direction.


6. INSTALL VANE PUMP ROTOR
  1. Coat the vane pump rotor with power steering fluid.

  1. Install the vane pump rotor.

    HINT:
    The vane pump rotor has no specific direction.

  1. Coat all 10 vane pump plates with power steering fluid.

  1. D030335E02
    Install the vane pump plates with the round end facing outward.

    NOTICE:
    Make sure that the vane pump plates are installed in the correct direction.


7. INSTALL VANE PUMP REAR HOUSING
  1. Coat a new O-ring with power steering fluid and install it onto the rear vane pump housing.

  1. C101387
    Align the straight pin of the rear vane pump housing with the dents of the vane pump cam ring, front vane pump side plate and the front vane pump housing, and install the rear vane pump housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install the service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.39 in.)
    Thread pitch:
    1.25 mm (0.0492 in.)
    Bolt length:
    50 mm (1.97 in.)

  1. G021500
    Using a torque wrench, check the rotating torque.

    Rotating torque:
    0.27 N*m (2.8 kgf*cm , 2.4 in.*lbf) or less

    If rotating torque is not as specified, check the installation condition of each part.


9. INSTALL FLOW CONTROL VALVE
  1. Coat the compression spring and the flow control valve with power steering fluid.

  1. C101967E01
    Install the compression spring and the flow control valve.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union to the front vane pump housing.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


10. INSTALL SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. Install the suction port union to the front vane pump housing with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Oct 2014)INSTALLATION (from Oct 2014) →