SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Oct 2014
| POWER WINDOW CONTROL SYSTEM DESCRIPTION |
The power window control system controls the power window UP/DOWN function by using regulator motors. This system is mainly controlled by the master switch built into the driver's door and regulator switches built into passenger's door. Pressing any of these regulator switches or the driver side door window switch mounted on the master switch transmits an UP/DOWN signal to the regulator motor for the corresponding power window, which then operates the power window UP/DOWN. Pressing any switch for the power windows except the driver's power window mounted on the master switch transmits a remote UP/DOWN signal to the front passenger power window switch via the direct line.
The power window control system has the following functions:
Function
Outline
Manual up-and-down function
Function that causes window to go up while power window switch is being pulled halfway up and to go down while pushed halfway down. Window stops as soon as the switch is released.
Jam protection function
Function that automatically stops power window and moves it downward if a foreign object gets jammed in door window during auto-up operation.
Remote control function
Function that allows power window master switch to control MANUAL up-and-down operation of front passenger door window.
Key-off operation function
Function that makes it possible to operate power window for approximately 45 seconds after ignition switch is turned to ACC or LOCK position, if either front door is not opened.
Fail-safe
A fail-safe function to disable a part of power window functions if pulse sensor in power window motor has a malfunction: - Driver door auto up-and-down function is disabled.
- Manual operation is possible by each power window switch.
- Driver door auto up-and-down function is disabled.
| CHECK WINDOW LOCK SWITCH |
![]() ![]() |
Check that the passenger side power window and rear power window operation is disabled when the window lock switch of the power window master switch is pressed.
Check that the passenger side power window and rear power windows can be operated when the window lock switch is pressed again.
| CHECK MANUAL UP/DOWN FUNCTION |
Check that the driver side power window operates as follows:
- Standard:
Condition
Master Switch
Switch Operation
Power Window
Ignition switch ON
Driver side
Pulled halfway up
UP (Closed)
Pushed halfway down
DOWN (Open)
Check that the power windows except the driver side power window operate as follows:
- Standard:
Condition
Master Switch
Switch Operation
Power Window
- Ignition switch ON
- Window lock switch OFF
Passenger side
Pulled halfway up
UP (Closed)
Pushed halfway down
DOWN (Open)
- Ignition switch ON
| CHECK AUTO UP/DOWN FUNCTION |
Check that the driver side power window operates as follows:
- Standard:
Condition
Master Switch
Switch Operation
Power Window
Ignition switch ON
Driver side
Pulled halfway up
UP (Closed)
Pushed halfway down
DOWN (Open)
| CHECK REMOTE MANUAL UP/DOWN FUNCTION |
Check that the power windows except the driver side power window operate as follows:
- Standard:
Condition
Master Switch
Switch Operation
Power Window
- Ignition switch ON
- Window lock switch OFF
Passenger side
Pulled halfway up
UP (Closed)
Pushed halfway down
DOWN (Open)
- Ignition switch ON
| MANUAL UP/DOWN FUNCTION USING DRIVER SIDE DOOR LOCK KEY CYLINDER |
Check that all power windows and sliding roof (standard type only) operate as follows, when the key is inserted into the driver side door lock key cylinder:
- Standard:
Condition
Key Operation
Position/Operation
No key in ignition key cylinder
Turned left (LOCK) for more than 1.5 seconds
Driver and passenger side power windows/UP
| CHECK MANUAL DOWN FUNCTION USING TRANSMITTER |
Check that all power windows operate as follows when operating the transmitter:
Condition
Transmitter Operation
Position/Operation
- No key in ignition key cylinder
- Any door unlocked
UNLOCK switch pressed for more than 1.5 seconds
Driver and passenger side power windows/ DOWN
- No key in ignition key cylinder
- HINT:
- For a sign for starting operation, the wireless door lock buzzer sounds once (answer-back).
| CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF |
When both of the following conditions are fulfilled, check that the power windows can be operated even after the ignition switch is turned off.
Within 45 seconds after the ignition switch is turned off.
The front doors are closed.
| CHECK JAM PROTECTION FUNCTION |
![]() ![]() |
- HINT:
- The jam protection function prevents any part of your body from getting caught by accident between the door frame and the door glass during power window operation.
- NOTICE:
- If the power window motor has just been reset, raise and lower the door glass several times using MANUAL function before performing the check.
Check that the door glass goes down by approx. 50 mm (1.97 in.) right when something gets caught between the door frame and door glass during power window operation. However, when the opening between the door frame and the door glass is less than 200 mm (7.87 in.), the door glass continues to go down and does not stop until an opening of 200 mm (7.87 in.) is achieved. Operative conditions:
- AUTO UP
- AUTO UP function after the ignition switch is turned off
- MANUAL UP function after the ignition switch is turned off
- MANUAL UP function using the driver side door lock key cylinder
- AUTO UP


