2014-2019 Hiace · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:
The normal signal conditions are as shown in the table below.
Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
  1. [OFF] stands for ground potential.
  2. [ON] stands for battery potential (+B).

P0504 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Depress and release brake pedal with ignition switch ON
Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
  1. Open or short in stop light switch signal circuit
  2. Stop light switch assembly
  3. ECM
Related Data List 
DTC No.
Data List
P0504
Stop Light Switch

WIRING DIAGRAM

A319500E02

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
  2. Stop light switch conditions can be checked using the GTS.
    1. Connect the GTS to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.
    5. Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation
Stop Light Switch
Depressed
ON
Released
OFF

1. CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)

  1. C197463E10
    Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B2-2 - Body ground
    Always
    11 to 14 V
    B2-4 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch)

  1. Reconnect the stop light switch connector.



NG
Go to step 6
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
Go to step 4
OK


3. CHECK ECM (STP AND ST1- VOLTAGE)
A275087E15
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    B72-34 (ST1-) - Body ground
    Released
    11 to 14 V
    Depressed
    0 to 3 V
    B72-35 (STP) - Body ground
    Released
    0 to 3 V
    Depressed
    11 to 14 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



OK
Go to step 5

NG
Go to step 6
4. REPLACE STOP LIGHT SWITCH ASSEMBLY
  1. Replace the stop light switch assembly.



NEXT
Go to step 7
5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Depress and release the brake pedal.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0504 Brake Switch "A" / "B" Correlation (Dec 2015 – Mar 2016)P0504 Brake Switch "A" / "B" Correlation (from Jan 2017) →