2014-2019 Hiace · Service Manual ENGINE

P1602 Deterioration of Battery

Diagnostic trouble codes · Vehicles built Jan 2015 – Nov 2015

Versions by build date: Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The ECM monitors the battery. When the engine is running (not cranking) and the battery voltage drops below a specified level, the ECU determines that there is battery deterioration and stores this DTC.
DTC Code
DTC Detection Condition
Trouble Area
P1602
  1. Diagnosis condition: Engine running (except when cranking)
  2. Malfunction status: Battery capacity is abnormally low for 10 seconds or more
  3. Trip count: 1 trip detection logic
  1. Battery
  2. Harness or connector

MONITOR STRATEGY

Frequency of operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Start the engine with all the accessories switched off.
  7. Wait for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
  9. Read Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P1602.
  12. Check the DTC judgment result.
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P0560 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FOR ANY OTHER DTCS OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    Only DTC P1602 is output.
    A
    Other DTCs are output in addition to DTC P1602.
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK CHARGING SYSTEM
  1. Check the charging system (Click here).



NG
REPAIR OR REPLACE CHARGING SYSTEM
OK


3. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

  1. A255690E75
    Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B94-1 (BATT) - Body ground
    Always
    9.5 to 16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P1550 Battery Current Sensor Circuit (+ P1551, P1552) (from Dec 2017)P1602 Deterioration of Battery (Dec 2015 – Mar 2016) →