2014-2019 Hiace · Service Manual BRAKE

CHECK FOR INTERMITTENT PROBLEMS

Troubleshooting · Vehicles built from Jan 2015


CHECK FOR INTERMITTENT PROBLEMS

HINT:
A momentary interruption (open circuit) in the connectors and/or wire harnesses between the sensors and ECUs can be detected using the ECU Data List function of the GTS.

  1. Turn the ignition switch off.

  2. Connect the GTS to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the GTS on.

  5. Follow the directions on the GTS to display the Data List and select areas where momentary interruptions should be monitored.

    HINT:
    1. A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).
    2. If the Error display remains displayed, measure the resistance between the ECUs and sensors, or between ECUs.
    3. The Error display on the GTS will remain displayed for 1 second after the harness signal changes from momentary interruption (open circuit) to the normal condition.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    EFI Communication Open
    ECM communication open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Deceleration Open
    Acceleration sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Master Cylinder Open
    Master cylinder pressure sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FR Speed Sensor Voltage Open
    Front speed sensor RH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Sensor Voltage Open
    Front speed sensor LH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RR Speed Sensor Voltage Open
    Rear speed sensor RH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Sensor Voltage Open
    Rear speed sensor LH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    M/C Pressure Sensor Noise
    Master cylinder pressure sensor noise detection / Error or Normal
    Normal
    Error: Momentary interruption
    Yaw Rate Sensor Voltage Open
    Yaw rate sensor voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    EFI Communication Invalid
    ECM communication invalid detection / Error or Normal
    Normal
    Error: Momentary interruption
    Master Cylinder Pressure Sensor Power Supply Open
    Master cylinder pressure sensor power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Solenoid Power Supply Open
    Solenoid power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Motor Power Supply Open
    Motor power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Stop Switch Open
    Momentary interruption (open circuit) status in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status / Error or Normal
    Normal
    Error: Momentary interruption

  6. While observing the screen, gently jiggle the connector or wire harness between the ECU and sensors, or between ECUs.

    OK:
    Normal is displayed.

    HINT:
    If the display changes, the connector and/or the wire harness has caused a momentary interruption of the circuit. Repair or replace the connector and/or wire harness as one of them is faulty.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Dec 2017)CALIBRATION (Jan 2015 – Nov 2017) →