2014-2019 Hiace · Service Manual ENGINE

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Oct 2014


ENGINE CONTROL SYSTEM
A317589E01
Text in Illustration 
*1
ECM
*2
Atmospheric Pressure Sensor
*3
Accelerator Pedal Position Sensor
*4
Ignition Switch Signal
*5
Starter Signal
*6
Vehicle Speed Signal
*7
DLC3
*8
Battery Voltage
*9
Other Signal
*10
Fuel Tank
*11
Suction Control Valve
*12
Fuel Temperature Sensor
*13
Fuel Supply Pump Assembly
*14
Generator
*15
Fuel Pressure Sensor
*16
Pressure Limiter
*17
Common Rail Assembly
*18
Injector Driver
*19
EDU Relay
*20
Diesel Throttle Body Assembly
*21
Manifold Absolute Pressure Sensor
*22
Intake Air Temperature Sensor (Turbo) (w/ Intercooler)
*23
Intercooler (w/ Intercooler)
*24
Intake Air Temperature Sensor
*25
VRV for EGR
*26
EGR Valve Position Sensor
*27
EGR Valve
*28
Injector Assembly
*29
Vacuum Pump
*30
Glow Plug
*31
Engine Coolant Temperature Sensor
*32
Glow Plug Relay (GLOW)
*33
Camshaft Position Sensor
*34
Crankshaft Position Sensor

COMMON RAIL SYSTEM DESCRIPTION

  1. Common rail system:
    The common rail system uses high-pressurized fuel for improved fuel economy and to provide robust engine power, while suppressing engine vibration and noise.
    This system stores fuel, which has been pressurized and supplied by the Fuel Supply Pump Assembly, in the common rail. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
    The ECM provides an electric current to the solenoid valve in the injector, using the EDU, to regulate the fuel injection timing and volume, and also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the Fuel Supply Pump Assembly to supply the fuel necessary to obtain the target fuel pressure.
    In addition, this system uses the 2-Way Valve (TWV) inside the injector to open and close the fuel passage. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
    The common rail system provides two split fuel injections. In order to soften combustion shock, this system performs "spilot-injection" as the subsidiary fuel injection prior to the main fuel injection. This helps to reduce engine vibration and noise.
    G039130E01

  2. Common rail system components:

    Component
    Description
    Common rail
    Stores high-pressure fuel produced by Fuel Supply Pump Assembly
    Fuel Supply Pump Assembly
    Operated by crankshaft via gear
    Supplies high-pressure fuel to common rail
    Injector
    Injects fuel to combustion chamber based on signals from ECM
    Fuel pressure sensor
    Monitors internal fuel pressure of common rail and sends signals to ECM
    Pressure limiter
    Opens pressure limiter valve to reduce internal pressure in common rail when common rail pressure exceeds specified level
    Suction control valve
    Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure

  3. Diagnostics trouble codes (DTCs) table for common rail system

    HINT:
    This table indicates typical DTC combinations for each malfunction occurrence.

    Trouble Area
    Malfunction
    DTC No.
    Injector
    Open or short in injector circuit
    P0200, P0088*
    Injector
    Stuck open
    P0088
    Fuel pressure sensor
    Open or short in fuel pressure sensor circuit or pressure sensor output fixed
    P0087, P0190, P0192, P0193
    Pressure limiter
    Stuck open
    P0093
    Pressure limiter
    Stuck closed
    P0088*
    Suction control valve
    Open or short in suction control valve circuit
    P0627, P1229, P0088*
    Suction control valve
    Stuck open
    P1229, P0088*
    EDU
    Faulty EDU
    P0093*, P0200*
    Common rail system (Fuel system)
    Fuel leaks in high-pressure areas
    P0093
    *: There may be no DTC output depending on condition of malfunction.

  4. Diagnostics trouble code description for common rail system:

    DTC No.
    Description
    P0087
    Fuel pressure sensor output does not change
    P0088
    Internal fuel pressure too high (200 MPa [2,039 kgf/cm2, 29,007 psi] or more)
    P0093
    Fuel leaks in high-pressure areas
    P0190
    Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
    P0192
    Open or short in fuel pressure sensor circuit (output voltage is too low)
    P0193
    Open or short in fuel pressure sensor circuit (output voltage is too high)
    P0200
    Open or short in EDU or injector circuit
    P0627
    Open or short in suction control valve circuit
    P1229
    Fuel over-feed


INJECTION CONTROL SYSTEM DESCRIPTION
The ECM controls the fuel injection system by using the injectors and fuel supply pump assembly. The ECM regulates the fuel injection volume and fuel injection timing by controlling both the duration and timing of energization to the solenoid valve in the injector. The ECM regulates injection pressure by controlling the suction control valve located in the fuel supply pump assembly.
The feed pump is used to pump fuel from the fuel tank to the fuel supply pump assembly.
A081479E09

FUEL SUPPLY PUMP ASSEMBLY OPERATION SYSTEM DESCRIPTION
Supply the rotation of the eccentric cam causes the ring cam to push plunger A upward as illustrated below. The spring force pulls plunger B (located opposite plunger A) upward. As a result, plunger B draws the fuel in, and plunger A pumps fuel out at the same time.
A096633E01

SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION

HINT:
The ECM controls the suction control valve operation to regulate the fuel volume that is pumped by the Fuel Supply Pump Assembly to the common rail. This control is performed to adjust the internal fuel pressure of the common rail to the targeted injection pressure.

  1. Small opening of the suction control valve:

    1. When the opening of the suction control valve is small, the fuel suction path is kept narrow. Therefore the transferable fuel volume is reduced.

    2. The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.

    3. Pumping will start at the time when the fuel pressure becomes higher than the common rail pressure.
      A081483E01

  2. Large opening of the suction control valve:

    1. When the opening of the suction control valve is large, the fuel suction path is kept wide. Therefore the transferable fuel volume is increased.

    2. If the plunger stroke is full, the suction volume becomes large because of the wide path.

    3. Pumping will start at the time when the fuel pressure becomes higher than the common rail pressure.
      A081484E01

← SYSTEM DIAGRAM (from Oct 2014)HOW TO PROCEED WITH TROUBLESHOOTING (Oct 2014 – Dec 2014) →