SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Jan 2017
| ENGINE CONTROL SYSTEM |


| *1 |
ECM |
*2 |
Fuel Supply Pump Assembly |
| *3 |
Pre-stroke Control Valve |
*4 |
Fuel Pressure Sensor |
| *5 |
Common Rail Assembly |
*6 |
Pressure Discharge Valve |
| *7 |
Glow Plug Controller |
*8 |
Intercooler Assembly |
| *9 |
Intake Air Temperature Sensor (Turbo) |
*10 |
Mass Air Flow Meter Sub-assembly |
| *11 |
Intake Air Temperature Sensor (Built Into Mass Air Flow Meter) |
*12 |
No. 1 EGR Cooler |
| *13 |
No. 1 Vacuum Switching Valve Assembly (for EGR Bypass Valve) |
*14 |
Injector Assembly |
| *15 |
Electric EGR Control Valve Assembly |
*16 |
Nozzle Vane Position Sensor |
| *17 |
DC motor |
*18 |
Camshaft Position Sensor |
| *19 |
Glow Plug Assembly |
*20 |
Manifold Absolute Pressure Sensor |
| *21 |
Diesel Throttle Body Assembly |
*22 |
Engine Coolant Temperature Sensor |
| *23 |
Crankshaft Position Sensor |
*24 |
Vacuum Switching Valve Assembly (for Swirl Control Valve) |
| *25 |
Exhaust Fuel Addition Injector Assembly |
*26 |
Exhaust Gas Temperature Sensor |
| *27 |
No. 2 Exhaust Gas Temperature Sensor |
*28 |
Differential Pressure Sensor Assembly |
| *29 |
No. 3 Exhaust Gas Temperature Sensor |
*30 |
Air Fuel Ratio Sensor |
| *31 |
Urea Injector Set |
*32 |
No. 4 Exhaust Gas Temperature Sensor |
| *33 |
Nitrogen Oxides Sensor |
*34 |
Urea Pump Control ECU |
| *35 |
Urea Pump |
*36 |
Accelerator Pedal Position Sensor |
| *37 |
Atmospheric Pressure Sensor |
- |
- |
| DIESEL PARTICULATE FILTER SYSTEM DESCRIPTION |
Diesel Particulate Filter System comprehensively regulates engine control (consists of a catalytic system and a fuel injection system) that purifies particulate matter (PM) by diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM with a catalytic converter with the Diesel Particulate Filter (DPF). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to produce and maintain a proper catalyst temperature for PM forced regeneration.
DPF components:
Component
Description
DPF Catalytic Converter
Reduces PM.
DOC Catalytic Converter
Reduces HC and CO.
Exhaust Fuel Addition Injector Assembly
Adds fuel into the exhaust port in order to raise catalyst temperature for PM forced regeneration.
- Exhaust Gas Temperature Sensor
- No. 2 Exhaust Gas Temperature Sensor
- No. 3 Exhaust Gas Temperature Sensor
Used for estimating the DPF catalytic converter temperature and adjusting fuel addition by ECM while PM forced regeneration is performed. Also detects the DPF catalytic converter temperature to prevent the catalytic converter temperature from rising too high.
Differential Pressure Sensor Assembly
Detects the volume of PM deposits and any incorrect vacuum hose arrangement on the DPF catalytic converter.
Air Fuel Ratio Sensor
Used for controlling the air-fuel ratio. By controlling the air-fuel ratio, combustion control and PM forced regeneration are properly regulated.
- Exhaust Gas Temperature Sensor
Diagnostics Trouble Codes (DTCs) table for DPF:
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
*: There may be no DTC output depending on the condition of the malfunction.Trouble Area
Malfunction
DTC No.
DPF catalytic converter
Deteriorated or clogged
P0420*, P062F, P200C*, P200E*, P244A*, P244B*, P2458*, P2463*
Exhaust Fuel Addition Injector Assembly
Stuck open
P20CF
Stuck closed
P0420*, P244A*, P2458*
Low fuel addition volume
P0420*, P244A*, P244B*, P2458*, P2463
Open in exhaust fuel addition injector circuit
P0420*, P20CD, P244A*, P2458*
Short in exhaust fuel addition injector circuit
P0420*, P20CF, P20CD, P244A*, P2458*
Open or short in exhaust fuel addition injector circuit
P0420*, P200C*, P200E, P20CF*, P20CD, P244A*, P2458*
Exhaust gas temperature sensor
Open in exhaust gas temperature sensor circuit
P0420*, P0545, P0546, P200C*, P200E*, P2032, P2033, P2080, P2084, P242B, P242C, P242D, P244A*, P2458*
Short in exhaust gas temperature sensor circuit
P0420*, P0545, P0546, P200C*, P200E*, P2002*, P2032, P2033, P2080, P2084, P242B, P242C, P242D, P244A*, P2458*
Exhaust gas temperature sensor
P0420*, P0545, P0546, P200C*, P200E*, P2032, P2033, P2080, P2084, P242B, P242C, P242D, P244A*, P2458*
Differential Pressure Sensor Assembly
Open in differential pressure sensor circuit
P0420*, P244A*, P2458*, P2454, P2455, P2463*
Short in differential pressure sensor circuit
P0420*, P244A*, P2458*, P2454, P2455, P2463*
Differential pressure sensor
P0420*, P244A*, P2458*, P2454, P2455, P2463*
Differential pressure sensor clogged
P0420*, P244A*, P2458*, P2453, P2463*
Incorrect vacuum hose arrangement of the differential pressure sensor
P0420*, P244A*, P2458*, P2453, P2463*
Air fuel ratio sensor
Open or short in air fuel ratio sensor or heater circuit
P0031, P0032, P2237, P2238, P2239, P2252, P2253, P244B*, P2463*
Air fuel ratio sensor
P0031, P0032, P2195, P2238, P2239, P2252, P2253, P244B*, P2463*
Exhaust gas leaks
Exhaust gas leaks
P0420*, P244A*, P2458*
Fuel leaks
Fuel leaks in fuel addition injector
P0420*, P2002*, P200C*, P200E*, P20CF*, P244A*, P244B*, P2458*, P2463*
Fuel supply pump assembly
Correct fuel pressure cannot be fed to the exhaust fuel addition injector
P0420*, P244A*, P244B*, P2458*, P2463*
Diagnostics trouble code description for DPF:
DTC No.
Description
P0031
Open in air fuel ratio sensor heater control circuit (Low output)
P0032
Short in air fuel ratio sensor or heater circuit (High output)
P0420
DPF catalytic converter insufficient temperature increase
P0545
Open or short in exhaust gas temperature sensor circuit (B1S1) (Low output)
P0546
Open or short in exhaust gas temperature sensor circuit (B1S1) (High output)
P200C
DPF catalytic converter abnormally high exhaust gas temperature
P200E
Catalyst system temperature too high bank 1
P2032
Open or short in exhaust gas temperature sensor circuit (B1S2) (Low output)
P2033
Open or short in exhaust gas temperature sensor circuit (B1S2) (High output)
P2080
Exhaust gas temperature sensor circuit range/performance (B1S1)
P2084
Exhaust gas temperature sensor circuit range/performance (B1S2)
P20CD
Open in exhaust fuel addition injector assembly circuit
P20CF
Exhaust fuel addition injector assembly stuck open
P2195
Air fuel ratio sensor stuck lean
P2237
Air fuel ratio sensor pumping current circuit/open
P2238
Open or short in air fuel ratio sensor or heater circuit (Low output)
P2239
Open or short in air fuel ratio sensor or heater circuit (High output)
P2252
Open or short in air fuel ratio sensor or heater circuit (Low output)
P2253
Open or short in air fuel ratio sensor or heater circuit (High output)
P242B
Exhaust gas temperature sensor circuit range / performance (B1S3)
P242C
Open or short in exhaust gas temperature sensor circuit (B1S3) (Low output)
P242D
Open or short in exhaust gas temperature sensor circuit (B1S3) (High output)
P244A
DPF catalytic converter excessive differential pressure (Low input)
P244B
DPF catalytic converter excessive differential pressure (High input)
P2453
Differential pressure sensor is clogged or has incorrect vacuum hose arrangement
P2454
Open or short in differential pressure sensor circuit (Low output)
P2455
Open or short in differential pressure sensor circuit (High output)
P2458
Diesel particulate filter regeneration duration
P2463
DPF catalytic converter soot deposition
| UREA SCR SYSTEM |


| *1 |
Nitrogen Oxigen Sensor |
*2 |
No. 4 Exhaust Gas Temperature Sensor |
| *3 |
Front Exhaust Pipe Assembly |
*4 |
Urea Injector Set |
| *5 |
Urea Tank Filler Pipe Assembly |
*6 |
Urea Tank Sub-assembly |
| *7 |
Urea Pump Control ECU |
*8 |
Urea Tube with Heater Assembly |
| *9 |
Urea Pump |
- |
- |
Urea SCR System:
A Urea SCR system is used to purify NOx in the exhaust gas. The urea SCR system injects urea solution into the exhaust gas to generate ammonia. The generated ammonia produces a chemical reaction with the NOx in the exhaust gas on the SCR catalyst, breaking it down into nitrogen and water, thereby purifying the exhaust gas.
The Urea SCR system is composed of a Urea pump control ECU, urea tank sub-assembly, urea injector set, urea pump, No. 4 exhaust gas temperature sensor and nitrogen oxides sensor.
In the Urea SCR system, the Urea pump control ECU controls the urea injector set and urea pump based on various signals.
Urea Pump:
The urea pump has the following functions:
Function
Outline
Pump Function
While performing feedback control according to the pressure sensor inside the urea pump, the pump raises the pressure to approximately 500 kPa, sending urea solution to the urea injector set.
Heating Function
The heater inside the urea pump is operated to thaw the urea solution so that exhaust gas can be purified even when the ambient temperature is low and the urea solution freezes. The heater turns on and off according to the urea solution temperature sensor inside the urea pump.
Filter Function
Foreign matter that enters the urea tank sub-assembly is collected by the filter inside the urea pump, preventing foreign matter from getting jammed in the urea pump and urea injector set.
Level Gauge Function
The fluid level position is detected by the float sensor inside the urea pump in order to detect the remaining quantity of urea solution inside the urea tank sub-assembly.
| COMMON RAIL SYSTEM DESCRIPTION |
Common rail system:
The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
This system stores fuel in the common rail, which has been pressurized and supplied by the fuel supply pump assembly. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
The ECM provides an electric current to the solenoid valve in each injector assembly to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the fuel supply pump assembly to supply the fuel necessary to obtain the target fuel pressure.
In addition, this system uses a solenoid valve inside each injector assembly to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
The common rail system allows a multi stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the "main-injection". This helps to reduce engine vibration and noise.
The system also performs "after-injection", which burns off fuel that was added during "pilot-injection" and "main-injection" and remained unburned, to increase the exhaust temperature for the DPF.

*1
Common Rail Assembly
*2
Fuel Pressure Sensor
*3
Pressure Discharge Valve
*4
ECM
*5
Crankshaft Position Sensor
*6
Camshaft Position Sensor
*7
Injector Assembly
*8
Pre-stroke Control Valve
*9
Fuel Supply Pump Assembly
*10
Exhaust Fuel Addition Injector Assembly
*11
Fuel Filter Assembly
*12
Fuel Tank Assembly


Fuel (High Pressure)


Fuel (Suction)


Fuel (Feed Pressure)


Fuel (Return)
- HINT:
- If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing a fuel injector, etc., the engine startability may deteriorate.
Common rail system components:
Component
Description
Common rail assembly
Stores high-pressure fuel produced by supply pump
Fuel supply pump assembly
- Operated by crankshaft via timing chain
- Supplies high-pressure fuel to common rail
Injector assembly
Injects fuel to combustion chamber based on signals from ECM
Fuel pressure sensor
Monitors internal fuel pressure of common rail and sends signals to ECM
Pressure discharge valve
Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high.
Pre-stroke control valve
Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure
- Operated by crankshaft via timing chain
Diagnostic trouble code (DTC) table for the common rail system:
- HINT:
- This table indicates typical DTC combinations for each malfunction occurrence.
*: There may be no DTC output depending on the condition of the malfunction.Trouble Area
Malfunction
DTC No.
Injector assembly
Open or short in injector circuit
P0093*, P0201, P0202, P0203, P0204
Stuck open
P0093
Stuck closed
P0301, P0302, P0303, P0304
Fuel pressure sensor
Open or short in fuel pressure sensor circuit or pressure sensor output fixed
P0087, P0190, P0191, P0192, P0193
Pressure discharge valve
Open or short in pressure discharge valve circuit
P0088*, P0093*, P1229*, P1271, P1272
Stuck open
P0093
Stuck closed
P0088*, P1272
Pre-stroke control valve
Open or short in suction control valve circuit
P0627, P1229, P0088*
Stuck open
P0088*, P1229
Common rail system (Fuel system)
Fuel leaks in high-pressure area
P0093
Diagnostic trouble code description for the common rail system:
DTC No.
Description
P0087
Fuel pressure sensor output does not change
P0088
Internal fuel pressure too high (240000 kPa [2447 kgf/cm2, 34800 psi] or more)
P0093
Fuel leaks in high-pressure areas
P0190
Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
P0191
Fuel pressure sensor circuit output fixed
P0192
Open or short in fuel pressure sensor circuit (output voltage is too low)
P0193
Open or short in fuel pressure sensor circuit (output voltage is too high)
P0201
Open or short in No. 1 injector circuit
P0202
Open or short in No. 2 injector circuit
P0203
Open or short in No. 3 injector circuit
P0204
Open or short in No. 4 injector circuit
P0301
Cylinder 1 misfire detected
P0302
Cylinder 2 misfire detected
P0303
Cylinder 3 misfire detected
P0304
Cylinder 4 misfire detected
P0627
Open or short in pre-stroke control valve circuit
P062D
ECM internal error
P1229
Fuel over-feed
P1271
Open or short in pressure discharge valve circuit
P1272
Pressure discharge valve stuck close
| FUEL SUPPLY PUMP OPERATION SYSTEM DESCRIPTION |
When the cam rotates the roller is pushed up, and in turn the plunger is pushed upward as well. When the plunger is not pushed up by the cam, it is pushed back down by the spring.


*1
Pre-stroke Control Valve
*2
Plunger
*3
Spring
*4
Shoe
*5
Roller
*6
Double Cam
The ECM controls the timing of the pre-stroke control valve opening to regulate the fuel quantity. Consequently, the fuel pressure in the common rail is controlled to the target injection pressure.
The longer the pre-stroke control valve remains open, the quantity of pressure-fed strokes will decrease, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.


*a
Return Fuel
-
-
The less time the pre-stroke control valve remains open, the quantity of pressure-fed strokes will increase, as well as the fuel discharge quantity.
Pumping will start when the fuel pressure has become higher than the common rail pressure.

