B2286 Runnable Signal Malfunction
Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016
Also covers:
- P0335 Crankshaft Position Sensor Circuit Malfunction (NE Signal)
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.- HINT:
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC Code |
DTC Detection Condition |
Trouble Area |
DTC Output Confirmation Operation |
| B2286 |
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match. |
|
Disconnect the cable from the negative (-) battery terminal, wait 30 seconds and reconnect the cable to the negative (-) battery terminal. Wait 20 seconds or more with the engine switch off, and then start the engine and maintain an engine speed of 1000 rpm or more for 20 seconds or more. |
| P0335 |
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication (1-trip detection logic*) do not match. |
|
Allow the engine to idle for 10 seconds or more. |
- *: Only detected while a malfunction is present and the engine switch is on (IG)
| Vehicle Condition when Malfunction Detected |
Fail-safe Function when Malfunction Detected |
|
|
| DTC |
Data List Item |
Active Test Item |
| B2286 P0335 |
Power Source Control
Starting Control
|
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
- Before replacing the certification ECU (smart key ECU assembly) or ECM, refer to the smart entry and start system (for Start Function) precaution (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. READ VALUE USING GTS (ENGINE CONDITION, ENGINE SPEED) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.
According to the display on the GTS, read the Data List.
Power Source Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Condition
Engine state/Stop or Run
Stop: Engine stopped
Run: Engine running
-
Starting Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Engine Speed
Engine speed/0 to 16383 r/min
Fluctuates in accordance with engine speed
-
- OK:
- The Data List item changes in accordance with the engine condition.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-1 (+B) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GROUND) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.


Text in Illustration *a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-10 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the B72 the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-6 (NE) - B72-60 (NEO)
Always
Below 1 Ω
B75-6 (NE) or B72-60 (NEO) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the B75 certification ECU (smart key ECU assembly) connector.
Reconnect the B72 ECM connector.
Check the engine speed input signal waveform at the terminal of the certification ECU.


Text in Illustration *a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-
- Standard Frequency:
Tester Connection
Condition
Specified Condition
B75-6 (NE) - Body ground
Engine stopped
No pulse generated
Engine running
Pulse generated
|
|
||||
| OK | ||
| ||
