C0278/11 Open in ABS Solenoid Relay Circuit
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Also covers:
- C0279/12 Short to B+ in ABS Solenoid Relay Circuit
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017
DESCRIPTION
This relay supplies power to each ABS solenoid.Immediately after the ignition switch is turned to the ON position, the relay turns on if the solenoid is determined to be normal as a result of self-diagnosis during initial check.
The relay turns off if an open/short is detected.
If the voltage supplied to the motor relay (+BS) is below the DTC detection threshold due to low voltage from the battery/alternator, the DTCs may be stored.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0278/11 |
With the IG1 terminal voltage 9.5 V or more, the solenoid relay contact is OFF for 0.2 seconds or more immediately after the solenoid relay is turned ON. |
|
| C0279/12 |
The solenoid relay contact is ON for 0.2 seconds or more when the solenoid relay is OFF. |
|
WIRING DIAGRAM
Refer to DTC C0226/21, C0236/22, and C0246/23 (Click here).INSPECTION PROCEDURE
| 1. INSPECT FUSE (ABS SOL FUSE) |
![]() ![]() |
Remove the ABS SOL fuse from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Specified Condition
ABS SOL (25 A) fuse
Below 1 Ω (Continuity)
|
|
||||
| OK | |
| 2. INSPECT SKID CONTROL ECU (+BS TERMINAL VOLTAGE) |
Install the ABS SOL fuse.

Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
B19-1 (+BS) - Body ground
Always
10 to 14 V
|
|
||||
| OK | |
| 3. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY) |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Specified Condition
B19-2 (GND1) - Body ground
Below 1 Ω
B19-24 (GND2) - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at the speed of 4 mph (6 km/h) or more.
Check that the same DTCs are recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- If a speed signal of 4 mph (6 km/h) or more is input to the skid control ECU, with the ignition switch on and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTCs (C0278/11 and C0279/12) are output
A
DTCs (C0278/11 and C0279/12) are not output
B
- HINT:
- If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
- If the normal system code is output, slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
- These DTCs may be memorized due to a malfunction in the connector terminal connection, etc.
- If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
|
|
||||
| A | ||
| ||

