2014-2019 Hiace · Service Manual BRAKE

C1251/51 Open in Pump Motor Circuit

Diagnostic trouble codes · Vehicles built Jan 2015 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017

DESCRIPTION

The motor relay (semiconductor relay) is housed in the brake actuator assembly and drives the pump motor based on a signal from the skid control ECU.
DTC No.
DTC Detection Condition
Trouble Area
C1251/51
When either of the following is detected during the initial check:
  1. The pump motor does not rotate normally.
  1. Open in the pump motor circuit continues for 2 seconds or more.
  1. Brake actuator pump motor circuit
  2. Brake actuator assembly

WIRING DIAGRAM

Refer to DTC C0273/13 and C0274/14 (Click here).

INSPECTION PROCEDURE

HINT:
After step 1 is complete, start the inspection from step 2 when using the intelligent tester, and from step 3 when not using the intelligent tester.


1. INSPECT SKID CONTROL ECU (GND TERMINAL CONTINUITY)

  1. C058919E29
    Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    B19-2 (GND) - Body ground
    Below 1 Ω
    B19-24 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Start the engine.

  1. Select the ACTIVE TEST mode on the intelligent tester.

    ABS: 
    Item (Display)
    Vehicle Condition / Test Details
    Diagnostic Note
    ABS Motor Relay
    Turns ABS motor relay ON / OFF
    Operating sound of motor is heard

  1. Check operating sound of the ABS motor when operating it with the intelligent tester.

    OK:
    The operating sound of the ABS motor is heard.



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


3. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at the speed of 4 mph (6 km/h) or more.

  1. Check that the same DTC is recorded (Click here).

    HINT:
    1. Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
    2. If a speed signal of 4 mph (6 km/h) or more is input to the skid control ECU, with the ignition switch on and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.


    Result:
    Condition
    Proceed to
    DTC (C1251/51) is output
    A
    DTC (C1251/51) not output
    B

    HINT:
    1. If any DTCs are output while jiggling a connector or wire harness of the brake actuator (skid control ECU), inspect and repair the connector or wire harness.
    2. If the normal system code is output, slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. These DTCs may be stored due to a malfunction in the connector terminal connection, etc.



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← C1251/51 Open in Pump Motor Circuit (Oct 2014 – Dec 2014)C1251/51 Open in Pump Motor Circuit (from Jan 2017) →