2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSPECT OVERDRIVE ONE WAY CLUTCH

  1. AT08138E03
    Hold the O/D direct clutch drum, and turn the input shaft. Check that the input shaft can be turned freely clockwise and locked counterclockwise.


2. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. AT08130
    Remove the over drive direct clutch.


3. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. AT08035
    Using a dial indicator, measure the inside diameter of the clutch drum bushings.

    Maximum inside diameter:
    27.11 mm (1.0673 in.)

    If the inside diameter is greater than the maximum, replace the clutch drum.


4. INSPECT PISTON STROKE OF OVERDRIVE DIRECT CLUTCH

5. REMOVE OVERDRIVE DIRECT CLUTCH CLUTCH DISC

  1. AT08131
    Using a screwdriver, remove the snap ring from the O/D direct clutch drum.

  1. Remove the flange, the 2 plates and the 2 discs.


6. INSPECT OVERDRIVE DIRECT CLUTCH CLUTCH DISC

  1. AT06455E02
    Check to see if the sliding surfaces of the disc, the plate and the flange are worn or burnt. If necessary, replace them.

    HINT:
    1. If the lining of the disc is peeled off or discolored, or even if only a part of the printed numbers is corroded, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


7. REMOVE OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. AT08132E02
    Place SST on the spring retainer, and compress the return spring with a press.
    SST
    09350-30020   (09350-07030)

    NOTICE:
    Stop compressing when the spring sheet is lowered to the place 1 to2mm(0.039 to 0.078 in.) from the snap ring groove, preventing the spring sheet from being deformed.

  1. Using snap ring pliers, remove the snap ring.

  1. Remove the piston return spring.


8. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D001246
    Measure the free length of the spring together with the spring seat.

    Standard free length:
    15.8 mm (0.622 in.)


9. REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

  1. AT03151
    Place the oil pump onto the torque converter clutch, and then place the O/D direct clutch onto the oil pump.

  1. Hold the O/D direct clutch piston by hand, and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the O/D direct clutch piston.

  1. Remove the O/D direct clutch piston.

    HINT:
    If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again, or wind vinyl tape around the piston end and remove it with needle nose pliers.

  1. Remove the 2 O-rings from the piston.


10. INSPECT OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

  1. AT08150
    Check that the check ball is free by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


11. REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE

  1. AT08133
    Using a screwdriver, remove the snap ring.

  1. AT08134
    Remove the ring gear flange.


12. REMOVE OVERDRIVE RETAINING PLATE

  1. AT08135
    Using a screwdriver, remove the snap ring.

  1. AT08146
    Remove the retaining plate.


13. REMOVE OVERDRIVE ONE WAY CLUTCH OUTER RACE

  1. AT08147
    Remove the over drive 1 way clutch outer race.


14. REMOVE OVERDRIVE ONE WAY CLUTCH

  1. AT04449
    Remove the O/D one-way clutch with the retainer from the outer race.

  1. Remove the 2 retainers from the one-way clutch.


15. REMOVE OVERDRIVE PLANETARY GEAR THRUST WASHER NO.3

  1. AT08148
    Remove the over drive planetary gear thrust washer.


16. INSPECT OVERDRIVE PLANETARY GEAR ASSEMBLY

  1. AT08143
    Using a dial indicator, measure the inside diameter of the planetary gear bushing.

    Maximum inside diameter:
    11.27 mm (0.4437 in.)

    If the inside diameter is greater than the maximum, replace the planetary gear.

  1. AT04450
    Using a feeler gauge, measure the planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.0079 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)

    If the clearance is greater than the maximum, replace the planetary gear assembly.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →