2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. FIX FORWARD CLUTCH ASSEMBLY

  1. AT08165
    Place wooden blocks, etc., to prevent the input shaft sub-assembly from touching the work stand, and place the overdrive support sub-assembly on them.

  1. Place the forward clutch assembly onto the overdrive support sub-assembly.


2. INSPECT PISTON STROKE OF FORWARD CLUTCH

  1. AT07843E02
    Using SST and a dial indicator, measure the forward clutch piston stroke while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
    SST
    09350-30020   (09350-06120)

    Piston stroke:
    0.60 to 1.00 mm (0.0236 to 0.0394 in.)

    If the piston stroke is less than the limit, parts may be assembled incorrectly, so inspect and reassemble them if necessary.
    If the piston stroke is outside the standard range, select another flange.

    HINT:
    There are 8 different flanges in thickness.

    Flange thickness:
    No.
    Thickness
    mm (in.)
    No.
    Thickness
    mm (in.)
    90
    3.0 (0.118)
    94
    3.8 (0.150)
    91
    3.2 (0.126)
    95
    4.0 (0.157)
    92
    3.4 (0.134)
    96
    4.2 (0.165)
    93
    3.6 (0.142)
    97
    4.4 (0.173)


3. REMOVE FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

  1. D001358
    Using a screwdriver, remove the snap ring from the forward clutch assembly.

    HINT:
    Tape up the screwdriver tip before use.

  1. Remove the flange, the 6 plates and the 6 discs.

  1. AT08177
    Remove the cushion plate.


4. INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

  1. D001216
    Check if the sliding surface of the disc, the plate and flange are worn or burnt. If necessary, replace them.

    HINT:
    1. If the lining of the disc is peeled off or discolored, or even if only a part of the printed numbers is corroded, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.


5. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D001274E02
    Place SST on the spring retainer, and compress the forward clutch return spring sub-assembly with a press.
    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. D001359
    Remove the forward clutch return spring sub-assembly.


6. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

  1. D025661
    Place the forward clutch assembly onto the overdrive support sub-assembly.

  1. While holding the forward clutch piston sub-assembly apply compressed air (196 kPa, 2.0 kgf/cm2, 28.5 psi) to the overdrive support sub-assembly.

  1. Remove the forward clutch piston sub-assembly.

  1. AT08179
    Remove the O-ring.


7. REMOVE FORWARD CLUTCH PISTON O-RING

  1. D001361E02
    Using a small screwdriver, remove the 2 O-rings.


8. INSPECT FORWARD CLUTCH PISTON SUB-ASSEMBLY

  1. D001424
    Check that the check ball is moves freely by shaking the piston.

  1. Check that the valve does not have leaks by applying low-pressure compressed air.


9. REMOVE INPUT SHAFT OIL SEAL RING

  1. AT08180
    Remove the 3 input shaft oil seal rings from the input shaft sub-assembly.


10. INSPECT INPUT SHAFT SUB-ASSEMBLY

  1. AT08171
    Using a dial indicator, measure the inside diameter of the input shaft sub-assembly bushing.

    Maximum inside diameter:
    24.08 mm (0.9480 in.)

    If the inside diameter is greater than the maximum, replace the input shaft sub-assembly.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →