INSTALLATION
Removal / installation · Vehicles built Jan 2015 – Dec 2016
Versions by build date: Jan 2015 – Dec 2016 from Jan 2017
| 1. INSTALL NO. 1 FLEXIBLE HOSE BRACKET |
Install the No. 1 flexible hose bracket with the bolt.
- Torque:
- 11 N*m{ 115 kgf*cm , 8 ft.*lbf }
| 2. INSTALL NO. 2 FLEXIBLE HOSE BRACKET |
Install the No. 2 flexible hose bracket with the bolt.
- Torque:
- 11 N*m{ 115 kgf*cm , 8 ft.*lbf }
| 3. INSTALL REAR BRAKE TUBE FLEXIBLE HOSE |
Connect the flexible hose to the connecting point with each brake tube, and then install 2 new clips.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

- Torque:
- Specified tightening torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
Text in Illustration *a
Torque Wrench Fulcrum Length
- HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.* lbf)
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- NOTICE:
- Do not bend or damage the brake tube.
- Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.
- Do not bend or damage the brake tube.
Connect the flexible hose to the connecting point with each brake tube, and then install 2 new clips.
Using a union nut wrench, connect each brake tube to the flexible hose while holding the flexible hose with a wrench.

- Torque:
- Specified tightening torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf }
Text in Illustration *a
Torque Wrench Fulcrum Length
- HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13 N*m (137 kgf*cm, 10 ft.* lbf)
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (Click here).
- NOTICE:
- Do not bend or damage the brake tube.
- Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.
- Do not bend or damage the brake tube.
| 4. ADD BRAKE FLUID |
- Fluid:
- SAE J1703 or FMVSS No. 116 DOT3 or equivalent
- NOTICE:
- Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.
| 5. BLEED BRAKE LINE |
Connect the vinyl tube to the bleeder plug.
Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.
At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.
Repeat this procedure until the air in the brake fluid is completely bled out.
Tighten the bleeder plug.
Front bleeder plug:
- Torque:
- 11 N*m{ 110 kgf*cm , 8 ft.*lbf }
Rear bleeder plug:
- Torque:
- 11 N*m{ 112 kgf*cm , 8 ft.*lbf }
Repeat the above procedure to bleed the air out of the brake line for each wheel.
| 6. INSPECT BRAKE FLUID LEVEL IN RESERVOIR |
Check the fluid level and add fluid if necessary.
- Fluid:
- SAE J1703 or FMVSS No.116 DOT3 or equivalent
- NOTICE:
- Do not remove the filter from the brake master cylinder reservoir and be sure to fill with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.
| 7. CHECK BRAKE FLUID LEAKAGE |
