2014-2019 Hiace · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 from Dec 2015


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  1. A101281E01
    Remove the oil filler cap sub-assembly.


2. REMOVE VENTILATION VALVE SUB-ASSEMBLY

  1. A101282
    Remove the ventilation valve sub-assembly.


3. REMOVE CAM POSITION SENSOR

  1. A101284E01
    Remove the bolt and camshaft position sensor.


4. REMOVE CRANK POSITION SENSOR

  1. G037914
    Remove the bolt and crank position sensor.


5. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A101285E01
    Remove the bolt and camshaft timing oil control valve.


6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts, head cover and 2 gaskets.


7. REMOVE CRANKSHAFT PULLEY

  1. G037261E04
    Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the bearing cap No.1, as shown in the illustration.

  1. A101288E01
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A101289E01
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)


8. REMOVE OIL PAN SUB-ASSEMBLY NO.2
  1. Remove the drain plug and gasket.

  1. A101291
    Remove the 18 bolts and 2 nuts.

  1. A101293
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the oil pan sub-assembly No.2.

    NOTICE:
    Do not damage the contact surfaces of the oil pans.


9. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A101294E03
    Remove the bolt, 2 nuts, oil strainer and gasket.


10. REMOVE OIL PAN SUB-ASSEMBLY

  1. A264837E01
    Remove the 16 bolts and 2 nuts.

  1. A101296E01
    Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Do not damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.

  1. A101297E01
    Remove the O-ring.


11. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A101298E01
    Remove the 19 bolts and 2 nuts shown in the illustration (w/o air conditioning).

  1. A192884
    Remove the 17 bolts and 2 nuts shown in the illustration (w/ air conditioning).

  1. A101299E01
    Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.

  1. A101300E01
    Remove the 3 O-rings.

  1. A101979
    Using a 10 mm socket hexagon wrench, remove the timing chain cover plug.


12. REMOVE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, water pump and gasket.


13. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A101302E01
    Using a screwdriver with its tip taped, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE OIL PUMP RELIEF VALVE

  1. A086864
    Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the valve spring and relief valve.


15. REMOVE TIMING CHAIN GUIDE

  1. A101304E01
    Remove the 2 bolts, timing chain guide and O-ring.


16. REMOVE CHAIN TENSIONER ASSEMBLY NO.1

NOTICE:
  1. When the chain tensioner is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90 degrees to the right.

  1. A101303E01
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.

  1. A101305
    Remove the bolt, nut, chain tensioner assembly No.1 and gasket.


17. REMOVE CHAIN TENSIONER SLIPPER

  1. A101307E01
    Remove the bolt and tensioner slipper.


18. REMOVE CHAIN VIBRATION DAMPER NO.1

  1. A101306E01
    Remove the bolt, nut, and vibration damper.


19. REMOVE CHAIN SUB-ASSEMBLY
  1. Remove the chain.


20. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

  1. A101308
    Remove the crankshaft timing gear from the crankshaft.


21. REMOVE CAMSHAFT BEARING CAP

  1. A101309E01
    Uniformly loosen and remove the 21 bearing cap bolts and 20 washers on the camshafts in the sequence shown in the illustration.

  1. A101310E01
    Remove the oil delivery pipe and O-ring from the bearing caps.

  1. A101311E01
    Remove the 9 bearing caps.


22. REMOVE CAMSHAFT

  1. A101312
    Remove the camshaft sub-assembly.


23. REMOVE NO.2 CAMSHAFT

  1. A101313
    Remove the No.2 camshaft sub-assembly.


24. REMOVE VALVE ROCKER ARM SUB-ASSEMBLY NO.1

  1. A101314E01
    Remove the 16 valve rocker arm sub-assemblies.


25. REMOVE CAMSHAFT TIMING GEAR OR SPROCKET

  1. A101317
    Fix the camshaft with a vise and then remove the sprocket bolt and camshaft timing sprocket.

    NOTICE:
    Do not damage the camshaft.


26. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. A062190E01
    Check the lock of the camshaft timing gear.

    1. Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.

      NOTICE:
      Do not damage the camshaft.

  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

      HINT:
      2 advance side paths are provided in the groove of the camshaft. Plug one of the paths with a rubber piece.

    2. Break through the tape of the advance side path and the retard side path on the opposite side to the hole of the advance side path, as shown in the illustration.

    3. A062191E01
      Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the two broken paths.

      CAUTION:
      Some oil splashing will occur. Cover the paths with a shop rag or piece of cloth.

    4. A062192E01
      Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.

      OK:
      Gear rotates in the advance direction.

      HINT:
      This operation releases the lock pin for the most retarded position.

    5. When the camshaft timing gear reaches the most advanced position, release the air pressure from the retard side path and advance side path, in that order.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Rotate the camshaft timing gear within its movable range several times, but do not turn it to the most retarded position. Check that the gear rotates smoothly.

      OK:
      Gear rotates in the advance direction.

      CAUTION:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear is locked at the most retarded position.


27. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

  1. A101318E02
    Remove the fringe bolt and camshaft timing gear.

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.


28. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A101319E03
    Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Do not drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.

  1. Remove the cylinder head.


29. REMOVE CYLINDER HEAD GASKET
  1. Remove the cylinder head and gasket.


30. REMOVE CHAIN VIBRATION DAMPER NO.2

  1. A101320E01
    Move the stopper plate downward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate upward to set the lock, and insert a hexagon wrench into the stopper plate hole.

  1. A101321E01
    Remove the bolt and chain vibration damper No.2.


31. REMOVE CHAIN VIBRATION DAMPER NO.3

  1. A101322E01
    Remove the 2 bolts and chain vibration damper No.3.


32. REMOVE CHAIN TENSIONER ASSEMBLY NO.2

  1. A101323E01
    Remove the hexagon wrench from the tensioner assembly

  1. Remove the nut and chain tensioner assembly No.2.


33. REMOVE NO.2 CHAIN SUB-ASSEMBLY

  1. A101324
    Remove the bolt, balanceshaft drive gear shaft and balanceshaft drive gear.

  1. Remove the crankshaft timing sprocket No.2 and chain.


34. REMOVE CHAIN VIBRATION DAMPER NO.4

  1. A101325E01
    Remove the 2 bolts and vibration damper No.4.


35. REMOVE CRANKSHAFT PULLEY SET KEY

  1. A101326
    Remove the 2 pulley set keys from the crankshaft.


36. REMOVE OIL FILTER SUB-ASSEMBLY

  1. G037302E01
    Using SST, remove the oil filter.
    SST
    09228-06501  

  1. G037462E01
    Using a 27 mm socket wrench, remove the oil filter union.


37. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. G037304E01
    Remove the 2 bolts and nut from the oil filter bracket.

  1. Remove the 2 screw plugs and 2 gaskets from the oil filter bracket.

  1. A101331E01
    Remove the oil filter bracket gasket and O-ring.

  1. A101977E01
    Using a hexagon wrench, remove the oil filter bracket union.


38. REMOVE W/HEAD TAPER SCREW PLUG NO.1

  1. A101908E01
    Remove the taper screw plug from the cylinder block.


39. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A101335E01
    Remove the 6 bolts.

  1. Using a screwdriver with its tip taped, pry out the oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.


40. REMOVE ENGINE REAR OIL SEAL

  1. A101332E01
    Place the oil seal retainer on wooden blocks.

  1. Using a screwdriver with its tip taped and a hammer, tap out the oil seal.

    HINT:
    Tape the screwdriver tip before use.


41. INSPECT CHAIN SUB-ASSEMBLY

  1. A101905E01
    Pull the chain with a force of 147 N (15 kgf, 33 Ibf) as shown in the illustration.

  1. Using vernier calipers, measure the length of 16 links.

    Maximum chain elongation:
    147.5 mm (5.807 in.)

    If the elongation is greater than the maximum, replace the chain.

    NOTICE:
    Perform the same measurement by pulling at random in 3 or more places to obtain an average.


42. INSPECT NO.2 CHAIN SUB-ASSEMBLY

  1. A101905E01
    Pull the chain with a force of 147 N (15 kgf, 33 Ibf) as shown in the illustration.

  1. Using vernier calipers, measure the length of 16 links.

    Maximum chain elongation:
    123.6 mm (4.866 in.)

    If the elongation is greater than the maximum, replace the chain.

    NOTICE:
    Perform the same measurement by pulling at random in 3 or more places to obtain an average.


43. INSPECT CHAIN TENSIONER ASSEMBLY NO.1

  1. A097905E01
    Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.


44. INSPECT CHAIN TENSIONER ASSEMBLY NO.2

  1. A101971E01
    Move the stopper plate downward to release the lock. Push the plunger and check that it moves smoothly.


45. INSPECT CAMSHAFT TIMING GEAR OR SPROCKET

  1. A097906E01
    Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.039 in.)

    If the distance is less than the minimum, replace the sprocket.
    If the worn area is too small or difficult to distinguish from a normal area, perform steps (b) and (c) below.

  1. Wrap the chain around the sprocket.

  1. Using vernier calipers, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (w/ chain):
    113.8 mm (4.480 in.)

    HINT:
    The vernier calipers must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


46. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

  1. A097907E01
    Measure the distance between the most worn out timing gear tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.039 in.)

    If the distance is less than the minimum, replace the timing gear.
    If the worn area is too small or difficult to distinguish from a normal area, perform steps (b) and (c) below.

  1. Wrap the chain around the timing gear.

  1. Using vernier calipers, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (w/ chain):
    113.8 mm (4.480 in.)

    HINT:
    The vernier calipers must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and timing gear.


47. INSPECT CRANKSHAFT TIMING GEAR

  1. A097908E02
    Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

    Minimum distance:
    1.0 mm (0.039 in.)

    If the distance is less than the minimum, replace the sprocket.
    If the worn area is too small or difficult to distinguish from a normal area, perform steps (b) and (c) below.

  1. Wrap the chain around the drive sprocket.

  1. Using vernier calipers, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (w/ chain):
    59.4 mm (2.338 in.)

    HINT:
    The vernier calipers must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


48. INSPECT CHAIN TENSIONER SLIPPER

  1. A097909E01
    Using vernier calipers, measure the tensioner slipper wear.

    Maximum wear:
    2.0 mm (0.079 in.)

    If the wear is greater than the maximum, replace the tensioner slipper


49. INSPECT CHAIN VIBRATION DAMPER NO.1

  1. A097910E01
    Using vernier calipers, measure the vibration damper wear.

    Maximum wear:
    2.0 mm (0.079 in.)

    If the wear is greater than the maximum, replace the vibration damper.


50. INSPECT TIMING CHAIN GUIDE

  1. A097911E01
    Using vernier calipers, measure the chain guide wear.

    Maximum wear:
    0.5 mm (0.020 in.)

    If the wear is greater than the maximum, replace the timing chain guide.


51. INSPECT CRANKSHAFT TIMING SPROCKET NO.2
  1. Wrap the chain around the sprocket.

  1. A101907
    Using vernier calipers, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (w/ chain):
    96.7 mm (3.807 in.)

    HINT:
    The vernier calipers must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


52. INSPECT BALANCESHAFT DRIVE GEAR SUB-ASSEMBLY
  1. Wrap the chain around the sprocket.

  1. A101906
    Using vernier calipers, measure the sprocket diameter with the chain.

    Minimum sprocket diameter (w/ chain):
    75.9 mm (2.988 in.)

    HINT:
    The vernier calipers must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the chain and sprocket.


53. INSPECT CHAIN VIBRATION DAMPER NO.2

  1. A101337E01
    Using vernier calipers, measure the vibration damper No.2 wear.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the wear is greater than the maximum, replace the vibration damper.


54. INSPECT CHAIN VIBRATION DAMPER NO.3

  1. A068741E01
    Using vernier calipers, measure the vibration damper No.3 wear.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the wear is greater than the maximum, replace the vibration damper.


55. INSPECT CHAIN VIBRATION DAMPER NO.4

  1. A068742E01
    Using vernier calipers, measure the vibration damper No.4 wear.

    Maximum wear:
    1.0 mm (0.039 in.)

    If the wear is greater than the maximum, replace the vibration damper.


56. INSPECT CYLINDER HEAD SET BOLT

  1. G035889E01
    Using vernier calipers, measure the minimum diameter of the elongated thread at the measuring point.

    Standard outside diameter:
    10.76 to 10.97 mm (0.4236 to 0.4319 in.)

    Minimum outside diameter:
    10.40 mm (0.4094 in.)

    If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.
    If the diameter is less than the minimum, replace the cylinder head bolt.


57. REMOVE VALVE STEM CAP

  1. A101315
    Remove the valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


58. REMOVE VALVE LASH ADJUSTER ASSEMBLY

  1. A103433
    Remove the valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.


59. INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.

  1. A101354E02
    Place the lash adjuster into a container full of engine oil.

  1. Insert the SST's tip into the lash adjuster's plunger and use the tip to press down on the checkball inside the plunger.

    SST
    09276-75010  

  1. Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of the SST is actually pressing the checkball as shown in the illustration. If the checkball is not pressed, air will not bleed.

  1. After bleeding the air, remove the SST. Then quickly and firmly press the plunger with a finger.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the lash adjuster.


60. REMOVE INTAKE VALVE

  1. A333831E01
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  
    09202-00021  

  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.


61. REMOVE EXHAUST VALVE

  1. A333832E01
    Using SST and wooden blocks, compress the compression spring and remove the valve retainer locks.
    SST
    09202-70020  
    09202-00021  

  1. Remove the retainer, compression spring, and valve.

    HINT:
    Arrange the removed parts in the correct order.


62. REMOVE VALVE STEM OIL SEAL

  1. A101371
    Using needle-nose pliers, remove the oil seals.


63. REMOVE VALVE SPRING SEAT
  1. Remove the valve spring seats from the cylinder head.


64. REMOVE OIL CONTROL VALVE FILTER

  1. A101413
    Using an 8 mm hexagon wrench, remove the screw plug.

  1. Remove the oil control valve filter and gasket.


65. REMOVE W/HEAD STRAIGHT SCREW PLUG NO.1

  1. A101373
    Using a 10 mm hexagon wrench, remove the 3 screw plugs and 3 gaskets.

    NOTICE:
    If water leaks from the w/ head straight screw plug No.1 or the plug corrodes, replace it.


66. REMOVE W/HEAD STRAIGHT SCREW PLUG NO.2

  1. A101374
    Using a 19 mm hexagon wrench, remove the screw plug and gasket.

    NOTICE:
    If water leaks from the w/ head straight screw plug No.2 or the plug corrodes, replace it.


67. INSPECT CYLINDER HEAD SUB-ASSEMBLY

  1. A101375E01
    Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder block and manifolds.

    Maximum warpage:
    0.05 mm (0.0020 in.)

    If the warpage is greater than the maximum, replace the cylinder head.

  1. A101376
    Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head.


68. INSPECT INTAKE VALVE SEATS

  1. A101377E01
    Apply a light coat of prussian blue (or white lead) to the valve face.

  1. Lightly press the valve face against the valve seat.

  1. Check the valve face and valve seat by using the following procedure.

    1. If prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.

    2. If prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).


69. INSPECT EXHAUST VALVE SEATS

  1. A101378E01
    Apply a light coat of prussian blue (or white lead) to the valve face.

  1. Lightly press the valve face against the valve seat.

  1. Check the valve face and valve seat by using the following procedure.

    1. If prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.

    2. If prussian blue appears around the entrire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.

    3. Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).


70. REPAIR INTAKE VALVE SEATS

NOTICE:
Keep the lip free from foreign matter.

  1. A110502E04
    If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.

  1. A101380E02
    If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.

  1. Handrub the valve and valve seat with an abrasive compound.

  1. Check the valve seating position.


71. REPAIR EXHAUST VALVE SEATS

NOTICE:
Keep the lip free from foreign matter.

  1. A110503E03
    If the seating is too high on the valve face, use 30° and 45° cutters to correct the seat.

  1. A101382E02
    If the seating is too low on the valve face, use 60° and 45° cutters to correct the seat.

  1. Handrub the valve and valve seat with an abrasive compound.

  1. Check the valve seating position.


72. INSPECT CAMSHAFT

  1. A101383
    Check the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.0012 in.)

      If the circle runout is greater than the maximum, replace the camshaft.

  1. A101384
    Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.855 to 42.955 mm (1.6872 to 1.6911 in.)

    Minimum cam lobe height:
    42.855 mm (1.6872 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. A101385
    Using a micrometer, measure the journal diameter.

    Standard journal diameter:
    Journal
    Diameter
    No.1 journal
    35.949 to 35.965 mm (1.4153 to 1.4159 in.)
    Other journal
    26.959 to 26.975 mm (1.0614 to 1.0620 in.)

    If the journal diameter is not as specified, check the oil clearance.


73. INSPECT NO. 2 CAMSHAFT

  1. A101386
    Check the camshaft for runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.0012 in.)

      If the circle runout is greater than the maximum, replace the camshaft.

  1. A101387
    Using a micrometer, measure the cam lobe height.

    Standard cam lobe height:
    42.854 to 42.954 mm (1.687 to 1.6911 in.)

    Minimum cam lobe height:
    42.854 mm (1.6872 in.)

    If the cam lobe height is less than the minimum, replace the camshaft.

  1. A101388
    Using a micrometer, measure the journal diameter.

    Standard journal diameter:
    Journal
    Diameter
    No.1 journal
    35.949 to 35.965 mm (1.4153 to 1.4159 in.)
    Other journal
    26.959 to 26.975 mm (1.0614 to 1.0620 in.)

    If the journal diameter is not as specified, check the oil clearance.


74. INSPECT CAMSHAFT THRUST CLEARANCE

  1. A101389
    Install the camshafts (See reassembly, step 49).

    Standard thrust clearance:
    0.10 to 0.24 mm (0.004 to 0.009 in.)

    Maximum thrust clearance:
    0.26 mm (0.010 in.)

    If the thrust clearance is greater than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.


75. INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the bearing caps and camshaft journals.

  1. Place the camshafts on the cylinder head.

  1. A101390E01
    Lay a strip of Plastigage across each of the camshaft journals.

  1. Install the bearing caps (See reassembly, step 49).

    Torque:
    16 N*m{ 160 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not turn the camshaft.

  1. Remove the bearing caps (See step 21).

  1. A101391E01
    Measure the Plastigage at its widest point.

    Standard journal diameter:
    Journal
    Diameter
    No.1 journal
    0.035 to 0.072mm (0.0014 to 0.0029 in.)
    Other journal
    0.025 to 0.062mm (0.0010 to 0.0024 in.)

    Maximum oil clearance:
    0.08 mm (0.003 in.)

    If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the cylinder head.

  1. Completely remove the Plastigage.


76. INSPECT INNER COMPRESSION SPRING

  1. A333833
    Using vernier calipers, measure the free length of the inner compression spring.

    Free length:
    52.13 mm (2.05 in.)

    If the free length is not as specified, replace the spring.

  1. A335450E02
    Using a steel square, measure the deviation of the inner compression spring at the position shown in the illustration.

    Maximum deviation:
    1.3 mm (0.0512 in.)

    Maximum angle (reference):
    2°

    If the deviation is greater than the maximum, replace the spring.


77. INSPECT INTAKE VALVE

  1. A101394E01
    Using vernier calipers, measure the valve's overall length.

    Standard overall length:
    106.26 mm (4.1835 in.)

    Minimum overall length:
    105.96 mm (4.1716 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A101395
    Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.470 to 5.485 mm (0.2154 to 0.2159 in.)

  1. A101396E03
    Using vernier calipers, measure the valve head margin thickness.

    Standard margin thickness:
    1.05 to 1.45 mm (0.0413 to 0.0571 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    If the overall length is less than the minimum, replace the valve.


78. INSPECT EXHAUST VALVE

  1. A101397E01
    Using vernier calipers, measure the valve's overall length.

    Standard overall length:
    106.74 mm (4.2024 in.)

    Minimum overall length:
    106.44 mm (4.1905 in.)

    If the overall length is less than the minimum, replace the valve.

  1. A101398
    Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.465 to 5.480 mm (0.2151 to 0.2157 in.)

  1. A101399E01
    Using vernier calipers, measure the valve head margin thickness.

    Standard margin thickness:
    1.2 to 1.6 mm (0.0472 to 0.0630 in.)

    Minimum margin thickness:
    0.50 mm (0.0197 in.)

    If the margin thickness is less than the minimum, replace the valve.


79. INSPECT VALVE GUIDE BUSHING

  1. A101400
    Using a caliper gauge, measure the inside diameter of the guide bush.

    Bush inside diameter:
    5.510 to 5.530 mm (0.2169 to 0.2177 in.)

  1. Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0024 in.) (Intake)
    0.030 to 0.065 mm (0.0012 to 0.0026 in.) (Exhaust)

    Maximum oil clearance:
    0.08 mm (0.0032 in.) (Intake)
    0.10 mm (0.0039 in.) (Exhaust)

    If the clearance is greater than the maximum, replace the intake valve and intake guide bush (See disassembly, step 80 and reassembly, step 19).
    If the clearance is greater than the maximum, replace the exhaust valve and exhaust guide bush (See disassembly, step 81 and reassembly, step 19).


80. REMOVE INTAKE VALVE GUIDE BUSH

  1. A101401E06
    Heat the cylinder head to 80 to 100°C (176 to 212°F)

  1. Place the cylinder head on wooden blocks.

  1. A101402E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


81. REMOVE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212 °F).

  1. Place the cylinder head on wooden blocks.

  1. G037435E01
    Using SST and a hammer, tap out the guide bush.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)


82. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A101473
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.150 to 0.350mm (0.0059 to 0.0138 in.)

    Maximum thrust clearance:
    0.40 mm (0.016 in.)

    If the thrust clearance is greater than the maximum, replace the connecting rod assembly(s). If necessary, replace the crankshaft.


83. INSPECT CONNECTING ROD OIL CLEARANCE
  1. Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.

    HINT:
    The matchmarks on the connecting rods and caps are for ensuring the correct reassembly.

  1. A101474
    Remove the 2 connecting rod cap bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. Clean the crank pin and bearing.

  1. Check the crank pin and bearing for pitting and scratches.

  1. A101475E01
    Lay a strip of Plastigage on the crank pin.

  1. A101476E01
    Check that the front mark of the connecting rod cap is facing forward.

  1. Install the connecting rod cap (See reassembly, step 17).

    NOTICE:
    Do not turn the crankshaft.

  1. A101477
    Remove the 2 bolts and connecting rod cap (See step (b) and (c) above).

  1. A103430E01
    Measure the Plastigage at its widest point.

    Standard oil clearance:
    0.039 to 0.066 mm (0.0015 to 0.0026 in.)

    Maximum oil clearance:
    0.066 mm (0.0026 in.)

    If the oil clearance is greater than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.
    If replacing a bearing, replace it with one that has the same number as its respective connecting rod cap. Each bearing's standard thickness is indicated by a 4, 5 or 6 mark on its surface.

    Standard crankshaft pin diameter:
    52.989 to 53.002 mm (2.0862 to 2.0867 in.)

    Standard bearing center wall thickness:
    Mark
    Thickness
    4
    1.484 to 1.487 mm (0.0584 to 0.0585 in.)
    5
    1.488 to 1.490 mm (0.0586 to 0.0587 in.)
    6
    1.491 to 1.493 mm (0.0587 to 0.0588 in.)

  1. Completely remove the Plastigage.


84. REMOVE PISTON SUB-ASSEMBLY W/CONNECTING ROD

  1. G035191E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


85. REMOVE CONNECTING ROD BEARING

HINT:
Arrange the removed parts in the correct order.


86. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A101481
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.020 to 0.220 mm (0.0008 to 0.0087 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is greater than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.

    Thrust Washer thickness:
    2.440 to 2.490 mm (0.0961 to 0.0980 in.)


87. REMOVE CRANKSHAFT

  1. A101482E01
    Uniformly loosen the 10 bearing cap bolts in several steps, in the sequence shown in the illustration.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.

  1. Lift out the crankshaft.

  1. G037374
    Remove the upper bearings and upper thrust washers from the cylinder block.

    HINT:
    Arrange the main bearing caps, bearings and thrust washers in the correct order.


88. REMOVE CRANKSHAFT BEARING

HINT:
Arrange the removed parts in the correct order.


89. REMOVE PISTON RING SET

  1. A101483
    Using a piston ring expander, remove the 2 compression rings.

  1. Using a piston ring expander, remove the oil ring rail.

  1. Remove the oil ring expander by hand.

    HINT:
    Arrange the piston rings in the correct order.


90. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A101333E01
    Remove the water drain cock sub-assembly from the cylinder block.

  1. Remove the water drain cock plug from the water drain cock sub-assembly.


91. REMOVE W/PIN PISTON SUB-ASSEMBLY

  1. Check the fitting condition between the piston and piston pin.

    1. G035197
      Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.

  1. Disconnect the connecting rod from the piston.

    1. A101515E02
      Using a screwdriver, pry off the snap rings from the piston.

    2. A100988E02
      Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    3. G036556
      Using a brass bar and plastic hammer, lightly tap out the piston pin and remove the connecting rod.

      HINT:
      1. The piston and pin are a matched set.
      2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


92. CLEAN W/PIN PISTON SUB-ASSEMBLY

  1. G035192
    Using a gasket scraper, remove the carbon from the piston top.

  1. G035193
    Using a groove cleaning tool or broken ring, clean the piston ring grooves.

  1. G035194
    Using solvent and a brush, thoroughly clean the piston.

    NOTICE:
    Do not use a wire brush.


93. REMOVE OIL NOZZLE NO.1 SUB-ASSEMBLY

  1. A101486E01
    Using a 5 mm hexagon wrench, remove the oil nozzles.


94. INSPECT OIL NOZZLE NO.1 SUB-ASSEMBLY
  1. Check the oil nozzles for damage or clogging.
    If necessary, replace the oil nozzle.


95. INSPECT BALANCE SHAFT THRUST CLEARANCE

  1. A101517
    Using a dial indicator, measure the thrust clearance while moving the balanceshaft back and forth.

    Standard thrust clearance:
    0.07 to 0.13 mm (0.0027 to 0.0051 in.)

    Maximum thrust clearance:
    0.20 mm (0.0079 in.)

    If the thrust clearance is greater than the maximum, replace the balanceshaft thrust washer. If necessary, replace the balanceshaft.


96. REMOVE NO.1 BALANCESHAFT

  1. A101518
    Remove the bolt.

  1. A101519
    Remove the balanceshaft from the cylinder block.

    NOTICE:
    When removing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.


97. REMOVE BALANCESHAFT DRIVEN GEAR NO.1
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Do not damage the balanceshaft.

  1. Remove the bolt.

  1. A101520E02
    Remove the balanceshaft driven gear No.1 (● 1), sliding key (● 2), balanceshaft thrust washer (● 3) and balanceshaft thrust spacer (● 4).


98. REMOVE NO.2 BALANCESHAFT

  1. A101521
    Remove the 2 bolts.

  1. A101522
    Remove the balanceshaft from the cylinder block.

    NOTICE:
    When removing the balanceshaft, make sure to support the balanceshaft with both hands and avoid scratching the balanceshaft bearing on the cylinder block side.


99. REMOVE BALANCESHAFT DRIVEN GEAR NO.2
  1. Mount the head portion of the balanceshaft in a vise.

    NOTICE:
    Do not damage the balanceshaft.

  1. A101523E02
    Remove the bolt.

  1. Remove the balanceshaft driven gear No.2 (● 1) and balanceshaft thrust washer No.2 (● 2).


100. INSPECT CYLINDER BLOCK FOR WARPAGE

  1. A101485
    Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.

    Maximum warpage:
    0.05 mm (0.0020 in.)

    If the warpage is greater than the maximum, replace the cylinder block.

  1. G035190
    Visually check the cylinder for vertical scratches.
    If deep scratches are present, rebore all the 4 cylinders. If necessary, replace the cylinder block.


101. INSPECT CYLINDER BORE

  1. A101487E01
    Using a cylinder gauge, measure the cylinder bore diameter at positions A in the thrust and axial directions.

    Standard diameter:
    94.990 to 95.003 mm (3.7398 to 3.7403 in.)

    Maximum difference diameter:
    0.2 mm (0.008 in.)

    If the diameter is greater than the maximum, rebore all the 4 cylinders. If necessary, replace the cylinder block.

  1. G035191E01
    Inspect the cylinder ridge.
    If the wear is less than 0.2 mm (0.008 in.), using a ridge reamer, grind the top of the cylinder.


102. CLEAN CYLINDER BLOCK

  1. G035189
    Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.

  1. Using a soft brush and solvent, thoroughly clean the cylinder block.


103. INSPECT PISTON DIAMETER

  1. G037359E02
    Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston end is as specified.

    Distance:
    13.8 mm (0.543 in.)

    Piston diameter:

    Diameter
    Standard
    94.940 to 94.950 mm (3.7378 to 3.7382 in.)


104. INSPECT PISTON OIL CLEARANCE
  1. Measure the cylinder bore diameter in the thrust direction (See step 101).

  1. Subtract the piston diameter measurement from the cylinder bore diameter measurement.

    Standard oil clearance:
    0.019 to 0.052 mm (0.0007 to 0.0020 in.)

    If the oil clearance is greater than the standard, replace all the pistons and rebore all the cylinders. If necessary, replace the cylinder block.

    HINT:
    1. Bore all the cylinders for the O/S piston outside diameter.
    2. Replace all the piston rings with ones to match the O/S pistons.

  1. If the oil clearance is greater than the standard:

    1. Prepare 4 new O/S pistons.

      O/S 0.50 piston diameter:
      95.440 to 95.450 mm (3.7575 to 3.7579 in.)

    2. Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the piston end is as specified.

      Distance:
      13.8 mm (0.543 in.)

    3. Calculate the amount each cylinder is to be rebored as follows:

      Size to be rebored = P + C - H 
      P
      Piston diameter
      C
      Piston clearance: 0.019 to 0.052 mm (0.0007 to 0.0020 in.)
      H
      Allowance for honing: 0.02 mm (0.0008 in.) or less

    4. Bore and hone the cylinders to calculated dimensions.

      Maximum honing:
      0.02 mm (0.0008 in.)

      NOTICE:
      Excess honing will destroy the finished roundness.


105. INSPECT RING GROOVE CLEARANCE

  1. A101489
    Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

    Ring groove clearance:
    Ring
    Clearance
    No. 1
    0.020 to 0.075 mm (0.0008 to 0.0030 in.)
    No. 2
    0.020 to 0.065 mm (0.0008 to 0.0026 in.)
    Oil
    0.020 to 0.070 mm (0.0008 to 0.0028 in.)

    If the clearance is not as specified, replace the piston.


106. INSPECT PISTON RING END GAP
  1. Insert the piston ring into the cylinder bore.

  1. A101490E04
    Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.

  1. A101491
    Using a feeler gauge, measure the end gap.

    Standard end gap:
    Ring
    End gap
    No. 1
    0.22 to 0.34 mm (0.0087 to 0.0134 in.)
    No. 2
    0.45 to 0.57 mm (0.0177 to 0.0224 in.)
    Oil
    0.10 to 0.40 mm (0.0039 to 0.0157 in.)

    Maximum end gap:
    Ring
    End gap
    No. 1
    0.90 mm (0.0354 in.)
    No. 2
    1.36 mm (0.0535 in.)
    Oil
    0.75 mm (0.0295 in.)

    If the end gap is greater than the maximum, replace the piston ring. If the end gap is less than the standard, even with a new piston ring, rebore all the 4 cylinders or replace the cylinder block.


107. INSPECT PISTON PIN OIL CLEARANCE

HINT:
There is only 1 type of supply part for piston with pin sub-assembly.

  1. A101492
    Using a caliper gauge, measure the inside diameter of the piston pin hole.

    Piston pin hole inside diameter:
    22.001 to 22.010 mm (0.8662 to 0.8665 in.)

  1. A101493E01
    Using a micrometer, measure the piston pin diameter.

    Piston pin diameter:
    21.997 to 22.009 mm (0.8660 to 0.8665 in.)

  1. A101494
    Using a caliper gauge, measure the inside diameter of the connecting rod bushing.

    Bushing inside diameter:
    22.005 to 22.014 mm (0.8663 to 0.8667 in.)

  1. Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

    Standard oil clearance:
    0.001 to 0.007 mm (0.00004 to 0.00028 in.)

    Maximum oil clearance:
    0.010 mm (0.0004 in.)

    If the oil clearance is greater than the maximum, replace the piston and piston pin as a set.

  1. A101496E01
    Subtract the piston pin diameter measurement from the bushing inside diameter measurement.

    Standard oil clearance:
    0.005 to 0.011 mm (0.0002 to 0.0004 in.)

    Maximum oil clearance:
    0.025 mm (0.0010 in.)

  1. If the oil clearance is greater than the maximum, replace the bushing. If necessary, replace the connecting rod and piston pin as a set.


108. INSPECT CONNECTING ROD SUB-ASSEMBLY

  1. Using a rod aligner and feeler gauge, check the connecting rod alignment.

    1. A054727
      Check for bend.

      Maximum bend:
      0.03 mm (0.0012 in.) per 100 mm (3.94 in.)

      If the bend is greater than the maximum, replace the connecting rod sub-assembly.

    2. A054728
      Check for twist.

      Maximum twist:
      0.15 mm (0.0059 in.) per 100 mm (3.94 in.)

      If the twist is greater than the maximum, replace the connecting rod sub-assembly.


109. REMOVE CONNECTING ROD SMALL END BUSH

  1. A054717
    Using SST and a press, press out the bush.
    SST
    09222-30010  


110. INSPECT CONNECTING ROD BOLT

  1. A101495
    Using vernier calipers, measure the tension portion diameter of the bolt.

    Standard diameter:
    7.2 to 7.3 mm (0.283 to 0.287 in.)

    Minimum diameter:
    7.0 mm (0.276 in.)

    If the diameter is less than the minimum, replace the bolt.


111. INSPECT CRANKSHAFT

  1. Inspect for circle runout.

    1. Place the crankshaft on V-blocks.

    2. A101497E01
      Using a dial indicator, measure the circle runout at the center journal.

      Maximum circle runout:
      0.03 mm (0.0012 in.)

      If the circle runout is greater than the maximum, replace the crankshaft.

  1. Inspect the main journals.

    1. A346739E01
      Using a micrometer, measure the diameter of each main journal.

      Standard Journal Diameter (No. 3 Journal):
      59.981 to 59.994 mm (2.36145 to 2.36196 in.)

      Standard Journal Diameter (Other Journal):
      59.987 to 60.000 mm (2.36169 to 2.36220 in.)

      Text in Illustration 
      *a
      No. 1
      *b
      No. 2
      *c
      No. 3
      *d
      No. 4
      *e
      No. 5
      If the diameter is not as specified, check the oil clearance (See step 112). If necessary, replace the crankshaft.

    2. Check each main journal for taper and out-of- round as shown in the illustration.

      Maximum taper and out-of-round:
      0.005 mm (0.0002 in.)

      HINT:
      If the taper and out-of-round is greater than the maximum, replace the crankshaft.

  1. Inspect the crank pin.

    1. A101499
      Using a micrometer, measure the diameter of each crank pin.

      Diameter:
      52.989 to 53.002 mm (2.0862 to 2.0867 in.)

      If the diameter is not as specified, check the oil clearance (See step 83). If necessary, replace the crankshaft.

    2. Check each crank pin for taper and out-of-round as shown in the illustration.

      Maximum taper and out-of-round:
      0.003 mm (0.0001 in.)

      If the taper and out-of-round is greater than the maximum, replace the crankshaft.


112. INSPECT CRANKSHAFT OIL CLEARANCE

HINT:
  1. Keep the lower bearings and crankshaft bearing caps together.
  2. Arrange the thrust washers in the correct order.
  3. Keep the upper crankshaft bearings and upper thrust washers together with the cylinder block.

  1. Clean each main journal and bearing.

  1. Check each main journal and bearing for pitting and scratches.
    If the journal or bearing is damaged, replace the bearing.

  1. Place the crankshaft on the cylinder block.

  1. A101505E01
    Lay a strip of Plastigage across each journal.

  1. A101506
    Install the 5 crankshaft bearing caps in their proper locations.

  1. Install the 5 crankshaft bearing caps with the 10 bolts (See reassembly, step 15).

    NOTICE:
    Do not turn the crankshaft.

  1. Remove the 10 bolts and 5 crankshaft bearing caps (See step 87).

  1. Measure the Plastigage at its widest point.

    A337687E01

    Text in Illustration 
    *a
    Plastigage
    *b
    No. 1 Journal
    *c
    No. 2 Journal
    *d
    No. 3 Journal
    *e
    No. 4 Journal
    *f
    No. 5 Journal
    *g
    Crankshaft Bearing Code
    *h
    Cylinder Block Journal Code
    *i
    Crankshaft Journal Code
    *j
    #1J, #2J, #4J, #5J
    *k
    #3J
    *l
    Bearing Code Chart

    Standard oil clearance:
    Bearing Cap
    Standard
    No. 3
    0.030 to 0.044 mm (0.00118 to 0.00173 in.)
    Others
    0.024 to 0.038 mm (0.000945 to 0.00150 in.)

    Maximum oil clearance:
    0.10 mm (0.00394 in.)

    1. If the oil clearance is more than the maximum, replace the crankshaft bearing.
    2. If replacing the cylinder block, measure the bearing standard clearance.
    3. Check the cylinder block journal code and crankshaft journal code and refer to the crankshaft bearing selection chart to select a bearing size.
    4. (Example) (Excluding No. 3 journal): When the cylinder block journal code is "D" and the crankshaft journal code is "4", select crankshaft bearing selection code "3" from the crankshaft bearing selection chart.

    Cylinder Block Main Journal Bore Diameter:
    Item
    Specified Condition
    Mark A
    64.004 to 64.006 mm (2.51984 to 2.51992 in.)
    Mark B
    64.007 to 64.008 mm (2.51996 to 2.51999 in.)
    Mark C
    64.007 to 64.008 mm (2.51996 to 2.51999 in.)
    Mark D
    64.011 to 64.012 mm (2.52011 to 2.52015 in.)
    Mark E
    64.013 to 64.014 mm (2.52019 to 2.52023 in.)
    Mark F
    64.015 to 64.016 mm (2.52027 to 2.52031 in.)
    Mark G
    64.017 to 64.018 mm (2.52035 to 2.52039 in.)
    Mark H
    64.019 to 64.020 mm (2.52043 to 2.52047 in.)
    Mark J
    64.021 to 64.022 mm (2.52051 to 2.52055 in.)


    Crankshaft Journal Bore Diameter:
    Item
    Specified Condition (No. 3 Journal)
    Specified Condition (Other Journal)
    Mark 0
    -
    59.999 to 60.000 mm (2.36216 to 2.36220 in.)
    Mark 1
    -
    59.997 to 59.998 mm (2.36208 to 2.36212 in.)
    Mark 2
    -
    59.995 to 59.996 mm (2.36200 to 2.36204 in.)
    Mark 3
    59.993 to 59.994 mm (2.36192 to 2.36196 in.)
    59.993 to 59.994 mm (2.36192 to 2.36196 in.)
    Mark 4
    59.991 to 59.992 mm (2.36185 to 2.36189 in.)
    59.991 to 59.992 mm (2.36185 to 2.36189 in.)
    Mark 5
    59.989 to 59.990 mm (2.36177 to 2.36181 in.)
    59.989 to 59.990 mm (2.36177 to 2.36181 in.)
    Mark 6
    59.987 to 59.988 mm (2.36169 to 2.36173 in.)
    59.987 to 59.988 mm (2.36169 to 2.36173 in.)
    Mark 7
    59.985 to 59.986 mm (2.36161 to 2.36165 in.)
    -
    Mark 8
    59.983 to 59.984 mm (2.36153 to 2.36157 in.)
    -
    Mark 9
    59.981 to 59.982 mm (2.36145 to 2.36149 in.)
    -


    Standard Bearing Center Wall Thickness:
    Item
    Specified Condition
    Mark 1
    1.987 to 1.990 mm (0.07823 to 0.07835 in.)
    Mark 2
    1.991 to 1.993 mm (0.07839 to 0.07846 in.)
    Mark 3
    1.994 to 1.996 mm (0.07850 to 0.07858 in.)
    Mark 4
    1.997 to 1.999 mm (0.07862 to 0.07870 in.)
    Mark 5
    2.000 to 2.002 mm (0.07874 to 0.07882 in.)

  1. Completely remove the Plastigage.


113. INSPECT CRANKSHAFT BEARING CAP SET BOLT

  1. A086985
    Using vernier calipers, measure the minimum diameter of the compressed thread at the measuring point.

    Standard diameter:
    10.76 to 10.97 mm (0.4236 to 0.4319 in.)

    Minimum diameter:
    10.66 mm (0.4197 in.)

    If the diameter is less than the minimum, replace the bolt.


114. INSPECT NO.1 BALANCESHAFT

  1. Inspect the diameter of the journal.

    1. A101524E01
      Using a micrometer, measure the diameter of the balanceshaft main journals.

      Main journal diameter:
      Journal
      Diameter
      A
      37.969 to 37.985 mm (1.4948 to 1.4955 in.)
      B
      37.449 to 37.465 mm (1.4744 to 1.4750 in.)

  1. Inspect the diameter of the bearing.

    1. A101526E01
      Using a cylinder gauge, measure the inside diameter of the balanceshaft bearing.

      Bearing inside diameter:
      Bearing
      Diameter
      A
      38.025 to 38.045 mm (1.4970 to 1.4978 in.)
      B
      37.525 to 37.545 mm (1.4774 to 1.4781 in.)

  1. Inspect oil clearance.

    1. Subtract the balanceshaft main journal diameter measurement from the balanceshaft bearing inside diameter measurement.

      Standard oil clearance:

      Clearance
      A
      0.040 to 0.076 mm (0.0016 to 0.0030 in.)
      B
      0.060 to 0.096 mm (0.0024 to 0.0038 in.)

      Maximum oil clearance::
      0.15 mm (0.0059 in.)

      If the oil clearance is greater than the maximum, replace the cylinder block and balanceshaft.


115. INSPECT NO.2 BALANCESHAFT

  1. Inspect the diameter of the journal.

    1. A101525E01
      Using a micrometer, measure the diameter of the balanceshaft main journals.

      Main journal diameter:
      Journal
      Diameter
      A
      37.969 to 37.985 mm (1.4948 to 1.4955 in.)
      B
      37.449 to 37.465 mm (1.4744 to 1.4750 in.)

  1. Inspect the diameter of the bearing.

    1. A101527E01
      Using a cylinder gauge, measure the inside diameter of the balanceshaft bearing.

      Bearing inside diameter:
      Bearing
      Diameter
      A
      38.025 to 38.045 mm (1.4970 to 1.4978 in.)
      B
      37.525 to 37.545 mm (1.4774 to 1.4781 in.)

  1. Inspect oil clearance.

    Standard oil clearance:

    Clearance
    A
    0.040 to 0.076 mm (0.0016 to 0.0030 in.)
    B
    0.060 to 0.096 mm (0.0024 to 0.0038 in.)

    Maximum oil clearance:
    0.15 mm (0.0059 in.)

    If the oil clearance is greater than the maximum, replace the cylinder block and balanceshaft.

← COMPONENTS (from Jan 2015)DISASSEMBLY (Jan 2015 – Nov 2015) →