2014-2019 Hiace · Service Manual ENGINE

P0500 Vehicle Speed Sensor

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
  1. Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.
  2. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.
    The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
  3. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.

A115899E20
DTC No.
DTC Detection Condition
Trouble Area
P0500
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Wheel speed sensor
  3. Combination meter
  4. ECM
  5. Skid control ECU

MONITOR STRATEGY

Required Sensors/Components (Main)
Vehicle speed sensor, Combination meter and Skid control ECU
Required Sensors/Components (Related)
Park/neutral position switch, Transmission revolution sensor (Speed sensor NT), Engine coolant temperature sensor, Crankshaft position sensor and Throttle position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS

Automatic Transmission Models 
Vehicle speed
9 km/h (6 mph) or higher
Transmission turbine speed
720 rpm or higher
Shift position
D
Gear position
2nd or higher
Park/neutral position switch fail
Not detected
Manual Transmission Models 
Fuel-cut
ON

TYPICAL MALFUNCTION THRESHOLDS

Automatic Transmission Models 
Duration of the following condition
8 seconds or more
Vehicle speed sensor signal
No pulse input
Manual Transmission Models 
Duration of the following condition
4.5 seconds or more
Vehicle speed sensor signal
No pulse input

CONFIRMATION DRIVING PATTERN

A240416E01
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on [A].
  6. Start the engine.
  7. On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.
  8. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
  9. Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].
  10. Stop the vehicle.
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  12. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0500.
  15. Check the DTC judgment result.
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


WIRING DIAGRAM

A340550E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (VEHICLE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the GTS.

    OK:
    Vehicle speeds displayed on GTS and speedometer display are equal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
  1. Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-6 (+S) - B94-44 (SPD)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK COMBINATION METER ASSEMBLY (+B VOLTAGE)
A127854E94
  1. Disconnect the combination meter connector.

    HINT:
    Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H20-6 (+S) - Body ground
    Ignition switch on
    4.5 to 5.5 V

    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPLACE ECM (Click here)
OK


4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
A261267E15
  1. Remove the combination meter assembly.

  1. Connect the combination meter connector.

  1. Move the shift lever to N.

  1. Jack up one of the rear wheels.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H20-6 (+S) - Body ground
    Ignition switch on
    Turn wheel slowly
    Voltage generated intermittently

    HINT:
    1. The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
    2. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

    *a
    Component with harness connected
    (Combination Meter Assembly)



NG
Go to step 5
OK

REPLACE ECM

5. CHECK COMBINATION METER ASSEMBLY
A261267E17
  1. Remove the combination meter assembly.

  1. Connect the combination meter connector.

  1. Move the shift lever to N.

  1. Jack up one of the rear wheels.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H20-7 (SI) - Body ground
    Ignition switch on
    Turn wheel slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.

    *a
    Component with harness connected
    (Combination Meter Assembly)



NG
Go to step 6
OK

REPLACE COMBINATION METER ASSEMBLY

6. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE ACTUATOR)
  1. Disconnect the ECM connector.

  1. Disconnect the brake actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H20-7 (SI) - B92-14 (SP1)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY


← P0500 Vehicle Speed Sensor (Apr 2016 – Dec 2016)P0504 Brake Switch "A" / "B" Correlation (Jan 2015 – Mar 2016) →