2014-2019 Hiace · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Oct 2014


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Start the engine.

  6. Turn the GTS on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to "Primary". Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    1. Measurement Group List / Description
      1. All Data / All data
      2. Primary / -
      3. Engine Control / Engine control system related data
      4. Diesel General / General data to analyze engine conditions for diesel engine
      5. Common Rail / Fuel system related data
      6. Common Rail (ALL) / Fuel system related detailed data
      7. Diesel EGR / EGR system related data
      8. Diesel Throttle / Diesel throttle system related data
      9. VN Turbo / VN turbo related data
      10. Diesel Exhaust / Exhaust system related data
      11. Diesel Starting / "Difficult to start" related data
      12. Diesel Rough Idle / "Rough idle" related data
      13. Diesel Lack of Power / "Lack of power" related data
      14. Diesel Knocking / "Knocking" related data
      15. Diesel Black Smoke / "Black smoke" related data
      16. Monitor Status / Monitor status related data
      17. Charging Control / Charging control system related data
      18. Compression / Data used during "Check the Cylinder Compression" Active Test
      19. A/T / Automatic transaxle system related data
      20. Vehicle Information / Vehicle information
      21. Catalytic Converter / Catalytic Converter related data

  8. Check the values by referring to the table below.


Engine Control
Calculate Load 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
  1. Idling: 10 to 40%
  2. Running without load (2500 rpm): 10 to 40%
Calculated by ECM
Malfunction in which turbo pressure
Diagnostic Note:
Calculated load = (Final injection volume / max. injection volume at current engine speed) x 100.
Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 6000 rpm
  1. 50 to 400 rpm: Cranking
  2. 700 to 800 rpm: Idling with warm engine
Sensor output (crankshaft position sensor)
  1. Crankshaft position sensor
  2. Crankshaft position sensor circuit
Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
MAP 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
MAP
Absolute pressure inside intake manifold/
Min.: 0 kPa, Max.: 255 kPa
  1. Idling: 95 to 105 kPa (depending on barometric pressure)
  2. Engine running at 2000 rpm: 105 to 130 kPa
  3. Engine running at 3000 rpm: 110 to 140 kPa
Sensor output (manifold absolute pressure sensor)
  1. Manifold absolute pressure sensor
  2. Intake related clog or leak
  3. Exhaust related clog
  4. Turbocharger sub-assembly
  5. Leak or clog in passages for turbocharger
  6. Exhaust leak
  7. Throttle valve stuck closed
Symptoms when out of range:
Lack of power
Diagnostic Note:
When the ignition switch is on or the vehicle is idling, the intake manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa).
Above approximately 1500 rpm, the turbo becomes effective and the pressure becomes higher than atmospheric pressure.
Vehicle Speed 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Sensor output (speed sensor)
  1. Speed sensor
  2. Speed sensor circuit
Diagnostic Note:
-
Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 140°C
After warming up engine: 70 to 90°C (158 to 194°F)
Sensor output (engine coolant temperature sensor)
  1. Engine coolant temperature sensor
  2. Thermostat
Symptoms when out of range:
Difficulty starting when engine is cold, rough idle, black smoke, lack of power
Diagnostic Note:
  1. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
  2. After a long soak, the coolant temperature, intake air temperature and ambient temperature are approximately equal.
Intake Air 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to temperature at location of intake air temperature sensor
Sensor output (intake air temperature sensor)
Intake air temperature sensor
Diagnostic Note:
  1. After a long soak, the engine coolant temperature, intake air temperature and ambient temperature are approximately equal.
  2. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
Intake Air Temp (Turbo) 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Intake Air Temp (Turbo)
Intake air temperature after intercooler/
Min.: -40°C, Max.: 190°C
70°C (158°F) or less
Sensor output (intake air temperature sensor after intercooler)
Decreased cooling efficiency of intercooler (contamination, clogging)
Diagnostic Note:
  1. This is the intake air temperature at the intake manifold (after the intercooler).
  2. During fail-safe operation, the value is set to 165°C (329°F). As the value is set to a high temperature, the turbo pressure may be suppressed and there may be a lack of power.
Radiator Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Radiator Coolant Temp
Engine coolant temperature (radiator side)/
Min.: -40°C, Max.: 140°C
After warming up engine: 70 to 90°C (158 to 194°F)
Sensor output engine coolant temperature (radiator) sensor
  1. Engine coolant temperature (radiator) sensor
  2. Thermostat
Diagnostic Note:
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
Initial Engine Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 120°C
Engine coolant temperature when engine started
Sensor output when engine started
-
Diagnostic Note:
For freeze frame data, this tells whether the malfunction happened at a cold start or with a warm engine.
Initial Intake Air Temp 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 120°C
Intake air temperature when engine started
Sensor output when engine started
-
Diagnostic Note:
-
Alternate Duty Ratio 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Alternate Duty Ratio
Alternator generation duty ratio/
Min.: 0%, Max.: 100%
  1. No electrical load at idling:
    20 to 60%
  1. High electrical load at idling:
    100%
Duty value from ALT terminal
  1. Battery deterioration
  2. Alternator malfunction
  3. Electric load, lights, etc.
Diagnostic Note:
  1. This is outputs the alternator generation duty and is used to determine the electrical load.
  2. Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction.
  3. Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration.
Glow Indicator 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Glow Indicator
Status of the glow indicator/
ON or OFF
-
-
-
Starter Signal 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Starter Signal
Starter signal/
ON or OFF
ON: Cranking
-
  1. OFF malfunction (ignition switch [STA] is ON but the signal is OFF and the starter is operating): Wire harness is open or shorted to ground
  2. ON malfunction (ignition switch [STA] is off but the signal is ON and the starter is not operating): Wire harness is shorted to +B
  3. Operation malfunction: ignition switch malfunction, starter relay malfunction, starter malfunction, battery or battery cable is defective, or wire harness is open or shorted
Symptoms when out of range:
  1. Ignition switch is on but the starter does not operate: Starting is not possible
  2. Ignition switch is off but the starter continues to operate: STA signal malfunction (P0617) is stored
Diagnostic Note:
Ignition switch (STA) output:
  1. ON: Starter is operating.
  2. OFF: Starter is not operating.
A/C Signal 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
A/C Signal
A/C (Air Conditioner) signal/
ON or OFF
ON: A/C on
A/C operation signal output from A/C amplifier
  1. ON: Operating
  2. OFF: Not operating
  1. A/C switch
  2. A/C amplifier
  3. A/C system malfunction, wire harness between A/C amplifier and ECU open or shorted
Symptoms when out of range:
OFF malfunction (OFF even when A/C switch is turned on):
  1. Engine speed decreases temporarily when the A/C is operating.
Diagnostic Note:
-
Idle Up Signal 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Idle Up Signal
Status of the idle up signal/
ON or OFF
-
-
-
Immobiliser Communication 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Immobiliser Communication
Immobiliser communication/
ON or OFF
  1. ON: Normal
  2. OFF: Engine cannot be started due to immobiliser communication malfunction
-
  1. Use of a nonregistered key
  2. Key battery is fully depleted
Stop Light Switch 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Stop Light Switch
Stop light switch/
ON or OFF
  1. ON: Brake pedal depressed
  2. OFF: Brake pedal released
Switch output (stop light switch)
  1. OFF malfunction: Wire harness (stop light switch to ECM, stop light switch to +B) open or shorted to ground
  2. ON malfunction: Wire harness (stop light switch to ECM) shorted to +B
  3. Stop light switch
Symptoms when out of range:
Stop light switch malfunction DTC P0504 is stored
Diagnostic Note:
Stop light switch (STP) operation condition:
  1. ON: Light is on (Brake pedal is depressed).
  2. OFF: Light is off (Brake pedal is released).
Neutral Position SW Signal 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Neutral Position SW Signal
Park/Neutral position switch status/
ON or OFF
ON: Shift lever in neutral
Switch output (park/neutral position switch)
-
Diagnostic Note:
-
Battery Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 15 V
11 to 14 V
-
-
Symptoms when out of range:
If 5 V or less, starting becomes difficult
Diagnostic Note:
If 11 V or less, characteristics of some electrical components change.
Atmosphere Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Atmosphere Pressure
Atmospheric pressure value/
Min.: 50 kPa, Max.: 120 kPa
Actual atmospheric pressure
Sensor output (atmospheric pressure sensor [built into ECM])
Atmospheric pressure sensor itself has failed (atmospheric pressure sensor is inside the ECM)
Diagnostic Note:
  1. With the ignition switch to ON, when the difference between the atmospheric pressure sensor and intake manifold absolute pressure is 10 kPa or more, there is a malfunction in one of the sensors.
  2. With the ignition switch to ON, when the atmospheric pressure is 0 kPa or 140 kPa, there is a malfunction in the sensor circuit.
  3. Standard atmospheric pressure: 101 kPa.
  4. For every 100 m increase in elevation, pressure drops by 1 kPa.
    This varies by weather (high atmospheric pressure, low atmospheric pressure).
TC and TE1 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
TC and TE1
TC and TE1 connection status for Active Test/
ON or OFF
-
-
-
Diagnostic Note:
When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected.
TC Terminal 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
TC Terminal
TC terminal status/
ON or OFF
-
-
-
# Codes (Include History) 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
-
-
Diagnostic Note:
Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up.
MIL 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
MIL
MIL status/
ON or OFF
OFF: MIL off
-
-
Engine Run Time 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Engine Run Time
Engine run time/
Min.: 0 sec., Max.: 65535 sec.
Time after the ignition switch turned on
Result of ECU calculations (using the engine speed)
-
Diagnostic Note:
Time passed since the ignition switch was turned on.
Time after DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min., Max.: 65535 min.
Time after DTCs cleared
-
-
Diagnostic Note:
Time elapsed since the DTCs were cleared (or shipment from the factory).
Distance from DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Distance from DTC Cleared
Distance driven after DTC cleared/
Min.: 0 km, Max.: 65535 km
Distance driven after DTCs cleared
-
-
Diagnostic Note:
  1. Distance driven since the DTCs were cleared.
  2. (Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred.
Warmup Cycle Cleared DTC 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Warmup Cycle Cleared DTC
Warmup cycles after DTC cleared/
Min.: 0, Max.: 255
-
-
-
Diagnostic Note:
  1. Number of engine warmup since DTCs were cleared.
  2. (Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred.
Dist Batt Cable Disconnect 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 16777215 km
-
-
-
Total Distance Traveled 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Total Distance Traveled
Total Distance Traveled/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected
-
-
Brake Override System 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Brake Override System
Brake override system/
ON or OFF
ON:
Brake override system operating
-
-
Communication with ECT 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Communication with ECT
Communication with ECT/
Comm or No Comm
-
-
-
OBD Requirements 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
OBD Requirements
Identifying OBD requirement
-
-
-
Diagnostic Note:
Not OBD compliant
Number of Emission DTC 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Number of Emission DTC
Number of emissions-related DTCs
Mini: 0, Max: 4250
-
-

Diagnostic Note:
-
Accel Position 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Accel Position
Accelerator position status/
Min.: 0%, Max.: 100%
  1. Accelerator pedal released:
    0%
  2. Accelerator pedal fully depressed:
    100%
  1. Accelerator pedal position sensor opening position
  2. ECT requested opening position
  3. Cruise requested opening position
  4. VSC requested opening position
-
Diagnostic Note:
  1. "Accel Position" is the accelerator opening amount (%) for engine control use.
  2. When the accelerator pedal position sensor output itself (Accelerator Position 1, Accelerator Position 2) is in the normal voltage range, another actuator malfunction has caused the fail-safe function to restrict the accelerator.
  3. Without cruise, ECT or VSC requests, and without accelerator restriction by the fail-safe function, this is adjusted in proportion to the amount the accelerator pedal is depressed by the driver.
  4. Accelerator pedal released: 0%
  5. Accelerator pedal fully depressed: 100%

HINT:
Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt % express the value obtained by dividing the output voltage from the accelerator pedal position sensor by 5. This is used only for diagnosing malfunctions in the accelerator pedal position sensor. Under normal conditions, it is sufficient to only check the final accelerator opening angle value "Accel Position".

Accel Sens. No.1 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Accel Sens. No.1 Volt %
Accelerator position No. 1/
Min.: 0%, Max.: 100%
  1. Accelerator pedal released:
    10 to 22%
  2. Accelerator pedal fully depressed:
    52 to 90%
Sensor output (Accelerator pedal position sensor)
-
Diagnostic Note:
Read value with ignition switch to ON (do not start engine)
Accel Sens. No.2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Accel Sens. No.2 Volt %
Accelerator position No. 2/
Min.: 0%, Max.: 100%
  1. Accelerator pedal released:
    24 to 40%
  2. Accelerator pedal fully depressed:
    68 to 99%
Sensor output (Accelerator pedal position sensor)
-
Diagnostic Note:
Read value with ignition switch to ON (do not start engine)

Vehicle Information
Model Code 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Model Code
Model code
-
-
-
Diagnostic Note:
Identifying model code: KDH2##
Engine Type 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Engine Type
Engine type
-
-
-
Diagnostic Note:
Identifying engine type: 2KD-FTV
Cylinder Number 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Cylinder Number
Cylinder number/
Min.: 0, Max.: 255
-
-
-
Diagnostic Note:
Identifying cylinder number: 4
Transmission Type 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Transmission Type
Transmission type/
MT or ECT 4th
-
-
-
Diagnostic Note:
Identifying transmission type:
  1. MT (Manual transmission)
  2. ECT 4th (Automatic transmission)
Destination 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Destination
Destination
-
-
-
Model Year 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Model Year
Model year/
Min.: 1900, Max.: 2155
-
-
-
Diagnostic Note:
Identifying model year: 20##
System Identification 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
System Identification
System identification
-
-
-
Diagnostic Note:
Identifying engine type: Diesel

Diesel Injection
Target Common Rail Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target Common Rail Pressure
Target common rail pressure/
Min.: 0 kPa, Max.: 250000 kPa
20000 to 180000 kPa when engine running
Target common rail pressure (ECU calculated value)
-
Diagnostic Note:
  1. Inspect the (actual) fuel pressure, comparing it with the common rail target value.
  2. Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions when idling after warm up the engine.
Common Rail Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Common Rail Pressure
Actual common rail pressure/
Min.: 0 kPa, Max.: 250000 kPa
Idling: 25000 to 35000 kPa
Sensor output (fuel pressure sensor)
  1. Fuel supply pump assembly
  2. High pressure pipes
  3. Fuel pressure sensor
  4. Injector assembly
  5. Feed pump (fuel supply pump assembly)
  6. Fuel filter element sub-assembly
  7. Pressure Limiter
  8. Air in the fuel pipes
  9. Lack of fuel
Symptoms when out of range:
Difficult to start, poor driveability, lack of power, abnormal combustion noise
Diagnostic Note:
  1. Common Rail Pressure is the actual common rail fuel pressure.
  2. Inspect by comparing the fuel pressure with the target fuel pressure.
  3. When in a stable condition such as when idling after warming up the engine, the fuel pressure is within +/- 5000 kPa of the target fuel pressure.
  4. The ECM uses fuel pressure for feedback control of the target fuel pressure via the fuel supply pump assembly.
    The injection amount is determined based on the injection timing and fuel pressure. Also, the spray pattern is selected based on the fuel pressure.
  5. For startup, at least 25000 kPa of fuel pressure is needed (take care as there is a response lag when the pressure rises).
  6. When the fuel pressure is below 25000 kPa, it may cause rough idling.
  7. When the fuel pressure has decreased by 20000 kPa from the target fuel pressure, there may be a lack of power.
  8. If actual fuel pressure is 5000 kPa higher than the target fuel pressure, P1229 will be stored.
  9. When the fuel pressure is higher than 220000 kPa, DTC P0088 will be stored.
Target Pump SCV Current 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target Pump SCV Current
Final pump current target value/
Min.: 0 mA, Max.: 4000 mA
Idling: 923 to 1123 mA
Target value control (pump current)
  1. Suction control valve malfunction
  2. Clogged fuel filter element sub-assembly
Symptoms when out of range:
Difficulty starting, lack of power or rough idling
Diagnostic Note:
  1. ECU-calculated value for the suction control valve actuation target current.
  2. Value is large when a high fuel pressure is desired.
  3. Normally, the value is between 800 and 2500 mA.
  4. If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.).
  5. When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.
Pump SCV Learning Value 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pump SCV Learning Value
Pump SCV learning value/
Min.: -4096 mA, Max.: 4095.8 mA
Min.: -100 mA, Max.: 100 mA
Learned value
  1. Suction control valve malfunction
  2. Clogged fuel filter element sub-assembly
Symptoms when out of range:
Difficulty starting, lack of power or rough idling
Diagnostic Note:
If the value is stuck at 200 mA or higher or -200 mA or less, it indicates that the operation is poor (poor movement due to deposits, etc.).
Pump SCV Status 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pump SCV Status
Pump SCV status/
ON or OFF
-
-
-
Pump SCV Duty Request 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pump SCV Duty Request
Pump SCV duty request/
Min.: 0%, Max.: 39.9%
-
Calculated value
-
Inj. FB Vol. for Idle 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Inj. FB Vol. for Idle
Idle stability status integral control volume/
Min.: -80 mm3/st, Max.: 79 mm3/st
-10 to 10 mm3/st
-
-
Symptoms when out of range:
Engine friction problem, compression problem or injector breakdown
Diagnostic Note:
  1. When the actual engine speed does not match the target idling speed, this corrects the injection volume.
    If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning.
  2. Only calculated and reflected at idle.
Injection Volume 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Injection Volume
Injection volume/
Min.: 0 mm3/st, Max.: 1279.98 mm3/st
Idling: 3.0 to 10 mm3/st
Calculated value
-
Diagnostic Note:
  1. Injection amount for each combustion.
  2. If injector assemblies are clogged fuel quality is poor, the fuel filter element sub-assembly is clogged, or engine friction increases, "Injection Volume" will increase.
  3. If there is a malfunction due to low turbocharger pressure or a low intake air volume, the injection volume is limited and there is a lack of power.
Inj Vol Feedback Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Inj Vol Feedback Learning
Injection volume feedback learning value/
Min.: -10 mm3/st, Max.: 9.92 mm3/st
-
-
-
Diagnostic Note:
-
Pilot Quantity Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pilot Quantity Learning
State of "Pilot Quantity Learning"/
Standby / Wait / Learn / Stop / Comple
-
Calculated value
-
Injector Pilot Quantity Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Injector Pilot Quantity Learning
Status of the injector pilot quantity learning/
Ready or NG
-
-
-
Actuator Pilot Quantity Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Actuator Pilot Quantity Learning
Status of the actuator pilot quantity learning/
Ready or NG
-
-
-
Temperature Pilot Quantity Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Temperature Pilot Quantity Learning
Status of the temperature pilot quantity learning/
Ready or NG
-
-
-
Catalyst Pilot Quantity Learning 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Catalyst Pilot Quantity Learning
Status of the catalyst pilot quantity learning/
Ready or NG
-
-
-
Injection Pressure Correction 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Injection Pressure Correction
Injection pressure feedback compensation volume/
Min.: -500 mm3/st, Max.: 780 mm3/st
-400 to 400 mm3/st at standard temperature
Calculated value
  1. Suction control valve malfunction
  2. Clogged fuel filter element sub-assembly
Diagnostic Note:
  1. When the (actual) fuel pressure is equal to the target fuel pressure, this value becomes 0.
  2. This indicator can be used for diagnosing supply pump related malfunctions.
  3. When this value (absolute value) is large, it indicates that the difference between the actual and target fuel pressure is also large.
    A positive value indicates that the pressure feed is being increased due to insufficient pressure. A negative value indicates that pressure is being reduced due to excessive rail pressure.
    When the suction control valve does not close properly, it causes rail overpressure, and this value slip to the negative volume side.
Injection Feedback Val #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection volume correction for each cylinder/
Min.: -10 mm3/st, Max.: 10 mm3/st
Idling: -3.0 to 3.0 mm3/st
Learned value
  1. Injector clogging
  2. Injector deterioration
  3. Decrease in cylinder compression
  4. Injector compensation code is incorrectly set (forgot to input code after replacement or made mistake during setting of code after replacing ECM with one from another vehicle)
Symptoms when out of range:
Rough idling, black smoke, white smoke, poor driveability, lack of power, abnormal combustion noise, difficult to start
Diagnostic Note:
  1. When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.
    Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.
  2. "Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.
  3. Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

    HINT:
    1. The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 4 cylinders is approximately 0 mm3/st.
    2. If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.

Pilot 1 Injection Period 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pilot 1 Injection Period
Pilot 1 injection period/
Min.: 0 μs, Max.: 65535 μs
-
Calculated value
-
Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Diagnostic Note:
Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur.
Pilot 2 Injection Period 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pilot 2 Injection Period
Pilot 2 injection period/
Min.: 0 μs, Max.: 65535 μs
Idling: 310 to 410 μs
Calculated value
-
Symptoms when out of range:
Combustion noise, poor driveability, white smoke
Diagnostic Note:
Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur.
Main Injection Period 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Main Injection Period
Main injection period/
Min.: 0 μs, Max.: 65535 μs
Idling: 450 to 640 μs
Calculated value
-
Diagnostic Note:
  1. When the fuel pressure becomes 15000 kPa or less, "Main Injection Period" is set to 0.
  2. When the engine will not start, confirm that injection is performed.
  3. When P0093, P0627 or P0200 is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.

    HINT:
    As the engine stalls 1 minute after the MIL illuminates, freeze frame data cannot be checked.

After Injection Period 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
After Injection Period
After injection period/
Min.: 0 μs, Max.: 65535 μs
-
Calculated value
-
Diagnostic Note:
Check to see if "After Injection Period" is not zero when the following symptoms occur:
Black smoke, poor driveability.
Pilot 1 Injection Timing 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pilot 1 Injection Timing
Pilot 1 injection timing/
Min.: -70°CA, Max.: 20°CA
-
Calculated value
-
Diagnostic Note:
-
Pilot 2 Injection Timing 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Pilot 2 Injection Timing
Pilot 2 injection timing/
Min.: -50°CA, Max.: 20°CA
Idling after engine warmed up and vehicle under normal atmospheric pressure: -10.3 to -9.3°CA
Calculated value
-
Diagnostic Note:
-
Main Injection Timing 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Main Injection Timing
Main injection timing/
Min.: -90°CA, Max.: 90°CA
Idling after engine warmed up and vehicle under normal atmospheric pressure: 2.5 to 3.5°CA
Calculated value
-
Diagnostic Note:
Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
After Injection Timing 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
After Injection Timing
After injection timing/
Min.: -10°CA, Max.: 50°CA
-
Calculated Value
-
Diagnostic Note:
-
Fuel Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Fuel Temperature
Fuel temperature/
Min.: -40°C, Max.: 140°C
Actual fuel temperature
Sensor output (fuel temperature sensor)
-
Diagnostic Note:
After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature.

EGR System
Target EGR Valve Pos 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target EGR Valve Pos
EGR valve target opening amount/
Min.: 0%, Max.: 100%
Idling after engine warmed up: 0 to 90%
ECU-calculated value based on sensors (manifold absolute pressure sensor, intake air temperature etc.).
-
Symptoms when out of range:
  1. When value is out of range and approaching 0%: intake or exhaust system blockage
  2. When value is out of range and approaching 100%: EGR pipe blockage
Diagnostic Note:
  1. Fully open: 100%.
  2. Fully closed: 0%.
  3. Used for comparison to "Actual EGR Valve Pos.".
Target EGR Valve Pos #2 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target EGR Valve Pos #2
EGR valve target opening amount/
Min.: 0%, Max.: 100%
-
-
-
Target EGR Pos 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target EGR Pos
EGR valve target opening amount/
Min.: 0%, Max.: 100%
Idling after engine warmed up: 0 to 90%
ECU-calculated value based on sensors (manifold absolute pressure sensor, intake air temperature etc.).
-
Symptoms when out of range:
  1. When value is out of range and approaching 0%: intake or exhaust system blockage
  2. When value is out of range and approaching 100%: EGR pipe blockage
Diagnostic Note:
  1. Fully open: 100%.
  2. Fully closed: 0%.
  3. Used for comparison to "Actual EGR Valve Pos.".
Actual EGR Valve Pos 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Actual EGR Valve Pos
EGR valve position/
Min.: 0%, Max.: 100%
Idling after engine warmed up: 0 to 90%
Calculated from EGR valve position sensor
-
Symptoms when out of range:
  1. EGR valve stuck open: Poor starts (engine does not stop), black smoke, white smoke, lack of power
  2. EGR valve stuck closed: Increased turbo booster noise
Diagnostic Note:
  1. Fully open: 100%.
  2. Fully closed: 0%.
  3. Inspect while comparing to "Target EGR Valve Pos".
  4. Check the valve movement via the Active Test.
  5. Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.
Actual EGR Valve Pos #2 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Actual EGR Valve Pos #2
EGR valve position/
Min.: 0%, Max.: 100%
-
-
-
EGR Position Sensor 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
EGR Position Sensor
EGR valve position sensor/
Min.: 0 V, Max.: 4.999 V
-
-
-
EGR Close Lrn. Val. 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
EGR Close Lrn. Val.
EGR fully closed position learned value/
Min.: 0 V, Max.: 5 V
0 to 1 V
EGR valve position sensor value when EGR valve fully closed
-
Diagnostic Note:
  1. This value is the EGR position sensor output voltage.
  2. When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area.
  3. As the lower and upper limits are 0 V and 1 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.).
EGR VSV 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
EGR VSV
VRV for EGR status/
ON or OFF
-
-
-

Diesel Throttle System
Target Throttle Position 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target Throttle Position
Target throttle position
Min.: -128%, Max.: 127%
  1. Throttle valve fully opened: 100%
  2. Throttle valve fully closed: 0%
Value calculated by ECM
-
Diagnostic Note:
If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Target Throttle Position #2 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Target Throttle Position #2
Target throttle position
Min.: -128%, Max.: 127%
-
-
-
Actual Throttle Position 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Actual Throttle Position
Actual diesel throttle position/
Min.: -20%, Max.: 120%
Idling after engine warmed-up: 5 to 100%
-
-
Symptoms when out of range:
  1. Stuck closed: Engine stall, difficult to start, lack of power, black smoke, rough idle
  2. Stuck open: Loud turbocharging sound, bad vibration when engine is stopped
  3. When ECM detects a malfunction of the diesel throttle (MIL on), engine power is restricted so that the vehicle can drive with a maximum speed of 80 to 100 km/h.
Diagnostic Note:
Closing percentage of the throttle valve.
  1. Fully closed: 0%.
  2. Fully open: 100%.

    HINT:
    There is no connection with the accelerator. However, under full load, the throttle is usually fully open (100%).

Actual Throttle Position #2 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Actual Throttle Position #2
Actual diesel throttle position/
Min.: -20%, Max.: 120%
-
-
-
Throttle Motor DUTY 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Throttle Motor DUTY
Diesel throttle motor duty/
Min.: 0%, Max.: 100%
-
-
-
Diagnostic Note:
When the moving force to open and close the diesel throttle valve increases, the value of Throttle Motor Duty increases.
Throttle Close Learning Val. 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Throttle Close Learning Val.
Throttle fully closed position learned value/
Min.: 0 deg, Max.: 84 deg
11 to 21 deg
-
-
Diagnostic Note:
  1. When the ignition switch is turned from on to off and 5 seconds elapse, learning of "Throttle Close Learning Val." will be complete.
  2. When "Throttle Close Learning Val." is outside of the normal range, a foreign object may be lodged in the throttle valve.
  3. If the value is stuck at the upper limit of 21.25 deg, there is a chance that a malfunction is present.
    However, as the initial value for the learned value is 21.25 deg, it is necessary to check the value after learning is completed.
Throttle Sensor Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Throttle Sensor Volt %
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
  1. Ignition switch ON: 60 to 80%
  2. Warmed-up and idling: 17 to 27%
Sensor output (throttle position sensor)
-
Symptoms when out of range:
  1. Stuck closed: Engine stall, difficult to start, rough idling, lack of power, black smoke, white smoke
  2. Stuck open: Loud turbocharging sound, bad vibration when engine is stopped
  3. When the ECM detects a malfunction with the diesel throttle (MIL on), engine power is restricted but city driving is possible.
Diagnostic Note:
  1. Throttle position sensor output voltage is converted using 5 V = 100%.
  2. When fully closed: 14%.
  3. When fully open: 70%.
  4. When the ignition switch is turned from off to ON, the throttle valve fully opens once.
  5. When the ignition switch is turned from ON to off, the throttle valve fully closes once.

Check Mode
Check Mode 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Check Mode
Check mode/
ON or OFF
ON: Check mode on
Refer to Check Mode Procedure.
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-

Monitor Result
Monitor Information 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
*
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
*
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
*
EGR/VVT Monitor
EGR/VVT Monitor/
Not Avl or Avail
-
*
EGR/VVT Monitor
EGR/VVT Monitor/
Compl or Incmpl
-
*
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
*
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*
O2S(A/FS) Monitor
O2S(A/FS) Monitor/
Not Avl or Avail
-
*
O2S(A/FS) Monitor
O2S(A/FS) Monitor/
Compl or Incmpl
-
*
A/C Monitor
A/C Monitor/
Not Avl or Avail
-
*
A/C Monitor
A/C Monitor/
Compl or Incmpl
-
*
2nd Air Monitor
2nd Air Monitor/
Not Avl or Avail
-
*
2nd Air Monitor
2nd Air Monitor/
Compl or Incmpl
-
*
EVAP Monitor
EVAP Monitor/
Not Avl or Avail
-
*
EVAP Monitor
EVAP Monitor/
Compl or Incmpl
-
*
Heated Catalyst Monitor
Heated Catalyst Monitor/
Not Avl or Avail
-
*
Heated Catalyst Monitor
Heated Catalyst Monitor/
Compl or Incmpl
-
*
Catalyst Monitor
Catalyst Monitor/
Not Avl or Avail
-
*
Catalyst Monitor
Catalyst Monitor/
Compl or Incmpl
-
*
*:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.

Support Data (Monitor Support Status)
Support Data 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Intake Air Temp (Turbo) Supported
Intake air temp (turbo) support/
Unsupp or Suppp
-
*1
Glow Indicator Supported
Glow indicator support/
Unsupp or Supp
-
*1
Target Throttle Position Supported
Target throttle position support/
Unsupp or Supp
-
*1
Target Throttle Position #2 Supported
Target throttle position #2 support/
Unsupp or Supp
-
*1
Actual Throttle Position Supported
Actual throttle position support/
Unsupp or Supp
-
*1
Actual Throttle #2 Position Supported
Actual throttle #2 position support/
Unsupp or Supp
-
*1
Target Common Rail Pressure Supported
Target common rail pressure support/
Unsupp or Supp
-
*1
Common Rail Pressure Supported
Common rail pressure support/
Unsupp or Supp
-
*1
Fuel Temperature Supported
Fuel temperature support/
Unsupp or Supp
-
*1
Target EGR Valve Pos Supported
Target EGR valve pos support/
Unsupp or Supp
-
*1
Target EGR Valve Pos #2 Supported
Target EGR valve pos #2 support/
Unsupp or Supp
-
*1
Actual EGR Valve Pos Supported
Actual EGR valve pos support/
Unsupp or Supp
-
*1
Actual EGR Valve Pos #2 Supported
Actual EGR valve pos #2 support/
Unsupp or Supp
-
*1
*1:
Supp: The item is supported by the vehicle.
Unsupp: The monitor is not supported by the vehicle.

AT (for Automatic Transmission)
Received MIL from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Received MIL from ECT
MIL status from ECT/
ON or OFF
ON: MIL ON
-
-
Diagnostic Note:
-
Shift Position Sig. from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
Shift Position Sig. from ECT
Shift position signal from ECT/
1st, 2nd, 3rd, 4th, 5th or 6th
-
-
-
Diagnostic Note:
-
A/T Oil Temp from ECT 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
A/T Oil Temp from ECT
ATF temperature from ECT/
Min.: -40°C, Max.: 215°C
With engine cold: Equal to ambient temperature
-
-
Diagnostic Note:
-
SPD (NO) 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
SPD (NO)
Output shaft speed/
Min.: 0 rpm, Max.: 12750 rpm
-
-
-
Diagnostic Note:
-
ECT Lock Up 
Tester Display
Measurement Item/Range
Normal Condition
Type
Cause of Out of Range
ECT Lock Up
Lock-up/
ON or OFF
ON: Lock-up operating
-
-
Diagnostic Note:
-

ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the EGR System
    Activate VRV for EGR
    ON/OFF
    Test is possible when the following conditions are met:
    1. Engine warmed up and idling.
    2. Shift lever in P.
    Connect the TC and TE1
    Turn on the TC and TE1 connection
    ON/OFF
    -
    Test the Fuel Leak
    Pressurize the common rail interior and check for fuel leaks
    Stop/Start
    1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2000 rpm when ON is selected
    2. Above conditions preserved while test is ON

    HINT:
    If this Active Test is performed when the engine is cold, combustion may become unstable. However, this is not a malfunction. It is only necessary to confirm that the pressure rises to the target pressure and that there are no fuel leaks.

    Control the Select Cylinder Fuel Cut
    Selected cylinder (cylinder #1 to #4) injector assembly fuel cut
    #1/#2/#3/#4
    ON/OFF
    Fuel injection is stopped while the test is ON.
    1. Confirm that the vehicle is stopped and the engine is idling.
    2. If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.

At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the GTS to the DLC3.
  4. Turn the ignition switch to ON and turn the GTS on.
  5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

    HINT:
    If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4 and Av Engine Speed of All Cyl.

  6. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

    HINT:
    After performing the above procedure, the "Check the Cylinder Compression" Active Test will start. Fuel injection for all cylinders is prohibited and the engine speed measurement of each cylinder enters standby mode.

  7. Crank the engine for about 10 seconds.
  8. Monitor the engine speed (Engine Speed of Cyl #1 to #4, Av Engine Speed of All Cyl) displayed on the GTS.

    HINT:
    At first, the GTS display will show the engine speed measurement of each cylinder to be extremely high. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.

    NOTICE:
    1. After the "Check the Cylinder Compression" Active Test is turned on, it will automatically turn off after 255 seconds.
    2. When the "Check the Cylinder Compression" test is off and the engine is cranked, the engine will start.
    3. If the "Check the Cylinder Compression" test needs to be performed after it is turned on and performed once, press "EXIT" to return to the Active Test menu screen. Then perform the "Check the Cylinder Compression" test again.
    4. Use a fully-charged battery.

← FAIL-SAFE CHART (from Oct 2014)DIAGNOSTIC TROUBLE CODE CHART (Oct 2014 – Dec 2014) →