2014-2019 Hiace · Service Manual TRANSMISSION

DIAGNOSIS SYSTEM

Troubleshooting · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


M-OBD
  1. When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the Intelligent Tester. Various data output from the TCM can then be read.

  2. FI02547
    OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:

    1. The emission control system / components

    2. The powertrain control components (which affect vehicle emissions)

    3. The computer
      In addition to, the applicable DTCs are recorded in the TCM memory.
      If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the TCM memory.

  3. C113768E01
    To check DTCs, connect the intelligent tester to the Data Link Connector 3 (DLC3) of the vehicle.
    The scan tool displays DTCs, the freeze frame data and a variety of the engine data.
    The DTCs and freeze frame data can be erased with the scan tool (Click here).


NORMAL MODE AND CHECK MODE

  1. A082779E59
    The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1-trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (Intelligent Tester only).


2-TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the TCM memory (1st trip). If the ignition switch is turned off and then turned to ON again, and the same malfunction is detected again, the MIL will illuminate.

FREEZE FRAME DATA
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air/fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

  2. A092901E08
    The Intelligent Tester records freeze frame data in five different instances: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. These data can be used to simulate the vehicle's condition around the time when the malfunction occurred. The data may help find the cause of the malfunction, or judge if the DTC is being caused by a temporary malfunction or not.


DLC3 (Data Link Connector 3)
A082779E81
  1. The ECM uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus "+" line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    SG (5) - Body ground
    Signal ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    11 to 14 V
    CANH (6) - CANL (14)
    CAN bus line
    Ignition switch off*
    54 to 69 Ω
    CANH (6) - CG (4)
    HIGH-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANL (14) - CG (4)
    LOW-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANH (6) - BAT (16)
    HIGH-level CAN bus line
    Ignition switch off*
    6 kΩ or higher
    CANL (14) - BAT (16)
    LOW-level CAN bus line
    Ignition switch off*
    6 kΩ or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minutes and do not operate the ignition switch, any other switches or the doors.

    Connect the cable of the intelligent tester to the DLC3, turn the ignition switch to ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
    If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
    If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.


INSPECT BATTERY VOLTAGE
If voltage is below 11 V, replace the battery before proceeding.

Battery Voltage:
11 to 14 V


CHECK MIL
  1. Check that the MIL illuminates when turning the ignition switch to ON.
    If the MIL does not illuminate, there is a problem in the MIL circuit (Click herefor 1KD-FTV w/DPF, Click herefor 1KD-FTV w/o DPF or Click here for 2KD-FTV).

  2. When the engine is started, the MIL should turn off.


ALL READINESS
For this vehicle, using the Intelligent Tester allows readiness codes corresponding to all DTCs to be read. When diagnosis (normal or malfunctioning) has been complete, readiness codes are set.
← DIAGNOSIS SYSTEM (Dec 2015 – Mar 2016)DIAGNOSIS SYSTEM (from Jan 2017) →