2014-2019 Hiace · Service Manual TRANSMISSION

HYDRAULIC TEST

Troubleshooting · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


PERFORM HYDRAULIC TEST

  1. Measure the line pressure.

    NOTICE:
    1. Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 50 to 80°C (122 to 176°F).
    2. The line pressure test should always be carried out in pairs. One technician should observe the conditions of wheels or wheel stoppers outside the vehicle while the other is performing the test.
    3. Be careful to prevent SST hose from interfering with the exhaust pipe.
    4. This check must be conducted after checking and adjusting engine.
    5. Perform under condition that A/C is OFF.
    6. When conducting stall test, do not continue more than 5 seconds.


    1. G023738E02
      Warm up the ATF (Automatic Transmission Fluid).

    2. Lift the vehicle up.

    3. Remove the test plug on the transmission case front left side and connect SST.

      SST
      09992-00095   (09992-00231, 09992-00271)

    4. Fully apply the parking brake and chock the 4 wheels.

    5. Start the engine and check idling speed.

    6. Keep your left foot pressing firmly on the brake pedal and shift into the D position.

    7. Depress the accelerator pedal all the way down. Quickly read the highest line pressure when engine speed reaches stall speed.

    8. In the same manner, do the test in the R position.

      Standard line pressure (for 1KD-FTV w/ DPF): 
      Condition
      D position kPa (kgf/cm2, psi)
      R position kPa (kgf/cm2, psi)
      Stall test
      1,095 to 1,230 kPa
      (11.2 to 12.5 kgf/cm2, 159 to 178 psi)
      1,490 to 1,815 kPa
      (15.2 to 18.5 kgf/cm2, 216 to 263 psi)
      Standard line pressure (for 1KD-FTV w/o DPF): 
      Condition
      D position kPa (kgf/cm2, psi)
      R position kPa (kgf/cm2, psi)
      Stall test
      1,115 to 1,255 kPa
      (11.4 to 12.8 kgf/cm2, 162 to 182 psi)
      1,270 to 1,605 kPa
      (13.0 to 16.4 kgf/cm2, 184 to 233 psi)
      Standard line pressure (2KD-FTV): 
      Condition
      D position kPa (kgf/cm2, psi)
      R position kPa (kgf/cm2, psi)
      Stall test
      1,010 to 1,135 kPa
      (10.3 to 11.6 kgf/cm2, 146 to 165 psi)
      1,290 to 1,575 kPa
      (13.2 to 16.1 kgf/cm2, 187 to 228 psi)
      Evaluation: 
      Problem
      Possible cause
      Measured values are higher than specified in all positions
      1. Shift solenoid valve (SLT) defective
      2. Regulator valve defective
      Measured values are lower than specified in all positions
      1. Shift solenoid valve (SLT) defective
      2. Regulator valve defective
      3. Oil pump defective
      4. O/D direct clutch defect
      Pressure is low in the D position only
      1. D position circuit fluid leak
      2. Forward clutch defective
      Pressure is low in the R position only
      1. R position circuit fluid leak
      2. Direct clutch defective
      3. 1st & reverse brake defective

← HYDRAULIC TEST (Oct 2014 – Dec 2014)MANUAL SHIFTING TEST (Oct 2014 – Dec 2014) →