2014-2019 Hiace · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Oct 2014

A194498E48

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
B88-2 (BATT) - D105-109 (E1)
W - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B88-25 (IGSW) - D105-109 (E1)
B - BR
Ignition switch
Ignition switch ON
11 to 14 V
B88-1 (+B) - D105-109 (E1)
L - BR
Power source of ECM
Ignition switch ON
11 to 14 V
B88-28 (MREL) - D105-109 (E1)
G - BR
EFI MAIN relay
Ignition switch ON
11 to 14 V
10 seconds elapsed after ignition switch off
0 to 1.5 V
B88-53 (VPA) - B88-54 (EPA)
L - G
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully released
0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed
2.9 to 4.2 V
B88-56 (VPA2) - B88-57 (EPA2)
B - GR
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
1.4 to 1.8 V
Ignition switch ON, accelerator pedal fully depressed
3.7 to 5.0 V
B88-55 (VCPA) - B88-54 (EPA)
W - G
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
B88-58 (VCP2) - B88-57 (EPA2)
R - GR
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
D105-110 (THA) - D105-87 (ETHB)
R - Y
IAT sensor
Idling, intake air temperature at 20°C (68°F)
0.5 to 3.4 V
D105-111 (THW) - D105-88 (ETHW)
R-W - Y
ECT sensor
Idling, engine coolant temperature at 80°C (176°F)
0.2 to 1.0 V
D105-113 (THIA) - D105-90 (ETHI)
R - Y
IAT sensor (Turbo)
Idling, intake air temperature at 0 to 80°C (32 to 176°F)
0.5 to 3.4 V
D105-114 (RTHW) - D105-74 (E2)
L - Y
Engine coolant temperature (radiator) sensor
Idling, radiator side engine coolant temperature at 80°C (176°F)
0.5 to 4.5 V
B88-36 (STA) - D105-109 (E1)
R - BR
Starter signal
Cranking
6.0 V or more
D105-50 (#1) - D105-109 (E1)
D105-49 (#2) - D105-109 (E1)
D105-48 (#3) - D105-109 (E1)
D105-47 (#4) - D105-109 (E1)
G - BR
GR - BR
Y - BR
B - BR
Injector
Idling
Pulse generation
(see waveform 1)
D105-103 (NE+) - D105-102 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(see waveform 2)
D105-80 (G+) - D105-79 (G-)
R - G
Camshaft position sensor
Idling
Pulse generation
(see waveform 2)
B88-35 (STP) - D105-109 (E1)
Y - BR
Stop light switch
Ignition switch ON, brake pedal depressed
7.5 to 14 V
Ignition switch ON, brake pedal released
0 to 1.5 V
B88-34 (ST1-) - D105-109 (E1)
R - BR
Stop light switch
(opposite to STP)
Ignition switch ON, brake pedal depressed
0 to 1.5 V
Ignition switch ON, brake pedal released
7.5 to 14 V
B88-26 (TC) - D105-109 (E1)
G - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
B88-14 (SPD) - D105-109 (E1)
P - BR
Speed signal from combination meter
Ignition switch ON, slowly rotate wheel
Pulse generation
(see waveform 3)
D105-118 (EGLS) - D105-95 (EEGL)
P - Y
EGR valve position sensor
Ignition switch ON
1.03 to 1.37 V
D105-94 (VCEG) - D105-95 (EEGL)
L - Y
Power source of EGR valve position sensor
Ignition switch ON
4.5 to 5.5 V
D105-117 (PIM) - D105-116 (EPIM)
P - Y
Manifold absolute pressure sensor
Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
0.1 to 0.7 V
Same as atmospheric pressure
0.8 to 1.5 V
Apply positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg)
1.6 to 2.3 V
D105-93 (VCPM) - D105-116 (EPIM)
L - Y
Power source of manifold absolute pressure sensor
Ignition switch ON
4.5 to 5.5 V
B88-29 (IREL) - D105-109 (E1)
R - BR
EDU relay
Ignition switch ON
0 to 1.5 V
B88-13 (TACH) - D105-109 (E1)
B - BR
Engine speed
Idling
Pulse generation
(see waveform 4)
D105-66 (PCR1) - D105-67 (E2S)
P - Y
Fuel pressure sensor
Idling
1.7 to 2.2 V
D105-68 (VCS) - D105-67 (E2S)
L - Y
Power source of fuel pressure sensor
Ignition switch ON
4.5 to 5.5 V
D105-58 (GREL) - D105-109 (E1)
G - BR
GLOW relay
Cranking
11 to 14 V
D105-112 (THF) - D105-89 (ETHF)
R - Y
Fuel temperature sensor
Ignition switch ON
0.5 to 3.4 V
D105-54 (ALT) - D105-109 (E1)
W - BR
Generator duty ratio
Idling
Pulse generation
(see waveform 5)
D105-41 (PCV+) - D105-81 (PCV-)
P - Y
Suction control valve
Idling
Pulse generation
(see waveform 6)
D105-51 (INJF) - D105-109 (E1)
LG - BR
EDU
Idling
Pulse generation
(see waveform 7)
D105-119 (VLU) - D105-96 (EVLU)
R - Y
Throttle position sensor
Ignition switch ON, throttle valve
fully opened
3.6 to 4.2 V
Ignition switch ON, throttle valve
fully closed
0.4 to 1.0 V
D105-97 (VCVL) - D105-96 (EVLU)
L - Y
Power source of throttle position sensor
Ignition switch ON
4.98 to 5.02 V
D105-78 (LUSL) - D105-109 (E1)
B - BR
Diesel throttle motor duty signal
Engine warmed up, racing engine
Pulse generation
(see waveform 8)
D105-83 (EGR) - D105-109 (E1)
B - BR
VRV for EGR
Ignition switch ON
Pulse generation
(see waveform 9)
D105-38 (NSW)* - D105-109 (E1)
B - BR
Park/neutral position switch assembly
Ignition switch ON, shift lever in P or N
Below 3 V
Ignition switch ON, shift lever not in P and N
11 to 14 V
B88-6 (CANH) - D105-109 (E1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 10)
B88-7 (CANL) - D105-109 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 11)
B88-4 (CAN+)* - D105-109 (E1)
L - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 10)
B88-5 (CAN-)* - D105-109 (E1)
Y - BR
CAN communication line
Ignition switch ON
Pulse generation
(see waveform 11)

HINT:
*: for Automatic Transmission


WAVEFORM 1
A009438E03
Injector No. 1 (to No. 4) injection signal 
ECM Terminal Name
(a) Between #1 and E1
(b) Between #3 and E1
(c) Between #4 and E1
(d) Between #2 and E1
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the injector injection.


WAVEFORM 2
A098437E05
Crankshaft position sensor signal and Camshaft position sensor signal 
ECM Terminal Name
(a) Between NE+ and NE-
(b) Between G+ and G-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the engine speed.


WAVEFORM 3
G037487E04
Vehicle speed signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Driving at vehicle speed of 40 km/h (25 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 4
A093225E19
Engine speed signal 
ECM Terminal Names
Between TACH and E1
Tester Ranges
5 V/DIV., 10 msec./DIV.
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 5
A155060E01
Generator duty ratio signal 
ECM Terminal Names
Between ALT and E1
Tester Ranges
5 V/DIV., 2 msec./DIV.
Conditions
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 6
A097624E03
Suction control valve signal 
ECM Terminal Name
Between PCV+ and PCV-
Tester Range
10 V/DIV., 5 msec./DIV.
Condition
Idling or cranking with warm engine

HINT:
The waveform varies depending on the suction control valve operation.


WAVEFORM 7
A009437E03
Injector injection confirmation signal 
ECM Terminal Name
Between INJF and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the injector injection.


WAVEFORM 8
A091225E03
Diesel throttle motor signal 
ECM Terminal Name
Between LUSL and E1
Tester Range
1 V/DIV., 2 msec./DIV.
Condition
Warm engine with racing engine

HINT:
The waveform varies depending on the throttle valve operation.


WAVEFORM 9
A096634E03
VRV for EGR Signal 
ECM Terminal Name
Between EGR and E1
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The waveform varies depending on the VRV for EGR operation.


WAVEFORM 9
G036660E03
CAN Communication Signal 
ECM Terminal Name
Between CANH and E1
Between CAN+ and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine is stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 10
G036661E03
CAN Communication Signal 
ECM Terminal Name
Between CANL and E1
Between CAN- and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine is stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.

← PROBLEM SYMPTOMS TABLE (from Jan 2017)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2014) →