2014-2019 Hiace · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Jan 2017

A335752E08

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
B97-1 (BATT) - D134-21 (E1)
W - W-B
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B97-6 (IGSW) - D134-21 (E1)
B - W-B
Ignition switch
Ignition switch ON
11 to 14 V
B97-2 (+B) - D134-21 (E1)
L - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
B97-3 (+B2) - D134-21 (E1)
L - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
B97-4 (+B3) - D134-21 (E1)
L - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
B97-46 (MREL) - D134-21 (E1)
G - W-B
EFI MAIN1 relay operation signal
Ignition switch ON
11 to 14 V
10 seconds elapsed after ignition switch off
0 to 1.5 V
D134-17 (+BD1) - D134-21 (E1)
B - W-B
EDU relay operation signal
Ignition switch ON
11 to 14 V
D134-16 (+BD2) - D134-21 (E1)
B - W-B
EDU relay operation signal
Ignition switch ON
11 to 14 V
B97-27 (GREL) - D134-21 (E1)
G - W-B
GLOW relay
Cranking
11 to 14 V
Idling (10 seconds or more after engine start)
0 to 1.5 V
B97-49 (VCPA) - B97-48 (EPA)
W - G
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
B97-50 (VCP2) - B97-51 (EPA2)
R - GR
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
B97-47 (VPA) - B97-48 (EPA)
L - G
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed
3.0 to 4.6 V
B97-52 (VPA2) - B97-51 (EPA2)
B - GR
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
0.9 to 2.3 V
Ignition switch ON, accelerator pedal fully depressed
3.4 to 5.0 V
D134-130 (VCVG) - D134-97 (EVG)
Y - L
Power source of mass air flow meter sub-assembly (for VG)
Ignition switch ON
4.8 to 5.2 V
D134-129 (VG) - D134-97 (EVG)
Y-G - L
Mass air flow meter sub-assembly signal
Ignition switch ON
Pulse generation
(See waveform 1)
D134-131 (THA) - D134-97 (EVG)
R - L
Intake air temperature sensor (built into mass air flow meter sub-assembly)
Idling, intake air temperature at 20°C (68°F)
0.5 to 3.4 V
D134-101 (THIA) - D134-133 (ETHI)
Y - BR
Intake air temperature sensor (turbo)
Idling, intake air temperature at 0 to 80°C (32 to 176°F)
0.5 to 3.4 V
D134-104 (THW) - D134-105 (ETHW)
R - BR
Engine coolant temperature sensor
Idling, engine coolant temperature at 80°C (176°F)
0.2 to 1.0 V
B97-29 (STA) - D134-21 (E1)
R - W-B
Starter signal
Cranking
6.0 V or higher
D134-57 (#1D+) - D134-58 (#1D-)
P - V
No. 1 injector assembly signal
Idling
Pulse generation
(See waveform 2)
D134-25 (#2D+) - D134-26 (#2D-)
L - W
No. 2 injector assembly signal
D134-55 (#3D+) - D134-56 (#3D-)
B - Y
No. 3 injector assembly signal
D134-27 (#4D+) - D134-28 (#4D-)
R - Y
No. 4 injector assembly signal
D134-111 (VCG) - D134-77 (G2-)
G - W
Power source of camshaft position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D134-78 (G2+) - D134-77 (G2-)
R - W
Camshaft position sensor
Idling
Pulse generation
(See waveform 3)
D134-110 (VCNE) - D134-109 (NE-)
B - Y
Power source of crankshaft position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D134-76 (NE+) - D134-109 (NE-)
L - Y
Crankshaft position sensor
Idling
Pulse generation
(See waveform 4)
B97-9 (STP) - D134-21 (E1)
Y - W-B
Stop light switch assembly
Ignition switch ON, brake pedal depressed
7.5 to 14 V
Ignition switch ON, brake pedal released
0 to 1.5 V
B97-10 (ST1-) - D134-21 (E1)
R - W-B
Stop light switch assembly
(opposite to STP)
Ignition switch ON, brake pedal depressed
0 to 1.5 V
Ignition switch ON, brake pedal released
7.5 to 14 V
B97-33 (TC) - D134-21 (E1)
G - W-B
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
B97-44 (SPD) - D134-21 (E1)
P - W-B
Speed signal from combination meter assembly
Ignition switch ON, slowly wheel rotated
Pulse generation
(See waveform 5)
D134-138 (VCPM) - D134-137 (EPIM)
R - G
Power source of manifold absolute pressure sensor
(specific voltage)
Ignition switch ON
4.5 to 5.5 V
D134-106 (PIM) - D134-137 (EPIM)
L - G
Manifold absolute pressure sensor
Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied
0.1 to 0.7 V
Same as atmospheric pressure
0.8 to 1.5 V
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied
1.6 to 2.3 V
B97-31 (TACH) - D134-21 (E1)
B - W-B
Engine speed
Idling
Pulse generation
(See waveform 6)
D134-93 (VCM) - D134-92 (E2M)
L - L
Power source of fuel pressure sensor (for PCR1)
Ignition switch ON
4.5 to 5.5 V
D134-91 (PCR1) - D134-92 (E2M)
W - L
Fuel pressure sensor (main)
Idling
1.8 to 2.1 V
D134-140 (VCS) - D134-107 (E2S)
V - L
Power source of fuel pressure sensor (for PCR2)
Ignition switch ON
4.5 to 5.5 V
D134-108 (PCR2) - D134-107 (E2S)
P - L
Fuel pressure sensor (sub)
Idling
1.2 to 1.5 V
D134-59 (PCV+) - D134-60 (PCV-)
B - Y
Pre-stroke control valve operation signal
Idling
Pulse generation
(See waveform 7)
D134-29 (PRV+) - D134-30 (PRV-)
R - L
Pressure discharge valve signal
Ignition switch turned off after idling
Pulse generation
D134-19 (VNM+) - D134-21 (E1)
L - W-B
Variable vane DC motor signal
(turbocharger nozzle vane control actuator)
Idling
Pulse generation
D134-49 (VNM-) - D134-21 (E1)
W - W-B
Variable vane DC motor signal
(turbocharger nozzle vane control actuator)
Idling
Pulse generation
D134-96 (VNVC) - D134-95 (VNE2)
V - L
Power source of nozzle vane position sensor
(turbocharger nozzle vane control actuator)
Ignition switch ON
4.5 to 5.5 V
D134-94 (VNA) - D134-95 (VNE2)
P - L
Nozzle vane position sensor signal
(turbocharger nozzle vane control actuator)
Ignition switch ON
2.3 to 2.7 V
D134-123 (VCVL) - D134-124 (EVLU)
P - V
Power source of throttle position sensor
Ignition switch ON
4.5 to 5.5 V
D134-125 (VLU) - D134-124 (EVLU)
Y - V
Throttle position sensor signal
Ignition switch ON, throttle valve fully opened
3.6 to 4.2 V
Ignition switch ON, throttle valve fully closed
0.4 to 1.0 V
D134-48 (M+) - D134-22 (ME01)
W - W-B
Diesel throttle duty signal
Engine warmed up, racing engine
Pulse generation
D134-18 (M-) - D134-22 (ME01)
R - W-B
Diesel throttle duty signal
Engine warmed up, racing engine
Pulse generation
D134-128 (VCEG) - D134-127 (EEGL)
R - W
Power source of EGR valve position sensor
Ignition switch ON
4.5 to 5.5 V
D134-126 (EGLS) - D134-127 (EEGL)
G - W
EGR valve position sensor
Ignition switch ON
0.6 to 1.4 V
D134-50 (EGM+) - D134-21 (E1)
P- W-B
EGR valve duty signal
Engine warmed up, idling
Pulse generation
D134-20 (EGM-) - D134-21 (E1)
Y - W-B
EGR valve duty signal
Engine warmed up, idling
Pulse generation
D134-45 (ECBV) - D134-21 (E1)
L - W-B
No. 1 vacuum switching valve assembly (for EGR bypass valve)
No. 1 vacuum switching valve assembly (for EGR bypass valve) on
0 to 1.5 V
No. 1 vacuum switching valve assembly (for EGR bypass valve) off
11 to 14 V
D134-100 (VCPX) - D134-99 (EPEX)
R - Y
Power source of differential pressure sensor
Ignition switch ON
4.5 to 5.5 V
D134-98 (PEX) - D134-99 (EPEX)
G - Y
Differential pressure sensor
Ignition switch ON
0.4 to 4.8 V
D134-23 (HA1A) - D134-53 (E04)
L - W-B
Air fuel ratio sensor heater
Ignition switch ON
11 to 14 V
Idling before air fuel ratio sensor warmed
Pulse generation
(See waveform 8)
D134-83 (A1A+) - D134-21 (E1)
B - W-B
Air fuel ratio sensor
Ignition switch ON
2.0 to 2.5 V
D134-115 (A1A-) - D134-21 (E1)
W - W-B
Air fuel ratio sensor
Ignition switch ON
2.0 to 2.5 V
D134-54 (FIV) - D134-21 (E1)
R - W-B
Exhaust fuel addition injector
Exhaust fuel addition injector operating
Pulse generation
D134-102 (THTO) - D134-134 (ETTO)
G - W
Exhaust gas temperature sensor
Engine warmed up, idling
0.2 to 4.95 V
D134-103 (THCI) - D134-135 (ETCI)
L - P
No. 2 Exhaust gas temperature sensor
Engine warmed up, idling
0.2 to 4.95 V
D134-139 (THCO) - D134-136 (ETCO)
B - Y
No. 3 Exhaust gas temperature sensor
Engine warmed up, idling
0.2 to 4.95 V
B97-38 (THSO) - B97-54 (ETSO)
B - R
No. 4 Exhaust gas temperature sensor
Engine warmed up, idling
0.2 to 4.95 V
D134-42 (SCV) - D134-51 (E01)
G - W-B
Vacuum switching valve assembly (for swirl control valve)
Idling
0 to 1.5 V
Engine speed 2600 rpm or more
11 to 14 V
B97-37 (THRW) - D134-99 (EPEX)
L - Y
Engine coolant temperature (radiator) sensor
Idling, engine coolant temperature (radiator) at -20 to 80°C (-4 to 176°F)
0.5 to 4.5 V
B97-57 (NSW) - D134-21 (E1)
B - W-B
Park/neutral position switch assembly
Ignition switch ON, shift lever in P or N
Below 3 V
Ignition switch ON, shift lever not in P and N
11 to 14 V
B97-26 (CANL) - D134-21 (E1)
W - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 9)
B97-13 (CANH) - D134-21 (E1)
R - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 10)
B97-56 (CAND) - D134-21 (E1)
L - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 9)
B97-41 (CANU) - D134-21 (E1)
Y - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 10)
D134-61 (LIN) - D134-21 (E1)
R - W-B
LIN communication line
Ignition switch ON
Pulse generation
(See waveform 11)
D134-51 (E01) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-52 (E02) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-21 (E1) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-22 (ME01) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
B97-14 (EC) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-47 (E1D1) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-46 (E1D2) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω
D134-53 (E04) - Body ground
W-B - Body ground
Earth (ground) circuit of ECM
Always
Below 1 Ω

WAVEFORM 1
A337204E02
Mass Air Flow Meter Sub-assembly Signal 
Item
Content
ECM Terminal Name
Between VG and EVG
Tester Range
1 V/DIV., 100 μsec./DIV.
Condition
Ignition switch ON

WAVEFORM 2
A346498E01
No. 1 (to No. 4) Injector Assembly Signal 
Item
Content
ECM Terminal Name
Between #1D+ and #1D-
Between #2D+ and #2D-
Between #3D+ and #3D-
Between #4D+ and #4D-
Tester Range
10 V/DIV., 1 msec./DIV.
Condition
Idling after engine warmed

HINT:
The waveform varies depending on the injector injection.


WAVEFORM 3
A340470E01
Camshaft Position Sensor Signal 
Item
Content
ECM Terminal Name
Between G2+ and G2-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling after engine warmed

HINT:
The waveform varies depending on the engine speed.


WAVEFORM 4
A362183E01
Crankshaft Position Sensor Signal 
Item
Content
ECM Terminal Name
Between NE+ and NE-
Tester Range
2 V/DIV., 10 msec./DIV.
Condition
Idling after engine warmed

HINT:
The waveform becomes shorter as the engine speed.


WAVEFORM 5
A208453E05
Vehicle Speed Signal 
Item
Content
ECM Terminal Name
Between SPD and E1
Tool Setting
5 V/DIV., 10 msec./DIV.
Condition
Driving at vehicle speed of 40 km/h (25 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 6
A292385E01
Engine Speed Signal 
Item
Content
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Idling after engine warmed

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A346499E01
Pre-stroke Control Valve Signal 
Item
Content
ECM Terminal Name
Between PCV+ and PCV-
Tester Range
10 V/DIV., 20 msec./DIV.
Condition
Idling after engine warmed

HINT:
The waveform varies depending on pre-stroke control valve operation.


WAVEFORM 8
A360352E01
Air Fuel Ratio Sensor Heater Signal 
Item
Content
ECM Terminal Name
Between HA1A and E04
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Idling before air fuel ratio sensor warmed

WAVEFORM 9
A208455E03
CAN Communication Signal 
Item
Content
ECM Terminal Name
Between CANL and E1
Between CAND and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 10
A208454E03
CAN Communication Signal 
Item
Content
ECM Terminal Name
Between CANH and E1
Between CANU and E1
Tester Range
1 V/DIV., 10 msec./DIV.
Condition
Engine stopped, ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 11
A349005E01
LIN Communication Signal 
Item
Content
ECM Terminal Name
Between LIN and E1
Tester Range
2 V/DIV., 10 msec./DIV.
Condition
Engine stopped, ignition switch ON

HINT:
The waveform varies depending on the LIN communication signal.

← PROBLEM SYMPTOMS TABLE (from Jan 2017)DIAGNOSIS SYSTEM (from Jan 2017) →