2014-2019 Hiace · Service Manual ENGINE

P2445 Secondary Air Injection System Pump Stuck Off Bank1

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Refer to P2431 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P2445
Secondary air pressure less than 1.0 kPa (7.5 mmHg) despite ECM commanding air pump to turn on (2 trip detection logic)
  1. Air pump
  2. Open in air pump circuit
  3. Secondary air injection system piping
  4. Vacuum hose (air pressure sensor - air switching valve)
  5. Air pressure sensor
  6. Open or short in air pressure sensor circuit
  7. Air injection control driver
  8. ECM

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the air switching valve of the secondary air injection system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:
  1. The pressure indicated by the air pressure sensor does not reach threshold levels despite the ECM turning on the air pump.
  2. The pressure indicated by the air pressure sensor exceeds threshold levels despite the ECM turning off the air pump.

MONITOR STRATEGY

Required Sensors/Components
Air pressure sensor
Frequency of Operation
Once per drive cycle

TYPICAL MALFUNCTION THRESHOLDS

P2445 Air Pump is Stuck OFF 
AIR pressure during Secondary Air Injection ON
Below 1.1 kPa (8.251 mmHg)

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the GTS to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the GTS on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the GTS on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the GTS initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Check for pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. After the "Secondary Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2445.
  16. Check the DTC judgment result.
    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

HINT:
  1. By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing System Check / Automatic Mode after the repair.
  2. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2445)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P2445 is output
    A
    DTC P2445 and P0418 are output
    B
    DTC P2445 and other DTCs (except P0418) are output
    C
    If any DTCs other than P2445 and/or P0418 are output, troubleshoot those DTCs first.



B
GO TO AIR PUMP INSPECTION PROCEDURE (Click here)

C
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, air pump and air switching valve operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Check that the air pump (AIR PUMP), air switching valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) status displayed on the GTS, indicate the conditions shown in the table below.

    Standard:
    GTS Operation
    AIR PUMP
    ASV
    PRESSURE*
    AIR PUMP: ON, ASV: OPEN
    ON
    ON
    1.1 kPa or more
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    OFF
    Less than 1.1 kPa

    *: Average pumping pressure. The pressure should be 1 kPa or more when the secondary air injection system operates.

  1. Turn the ignition switch off.

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (Wait or Error).
      If an Error is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear DTCs (if stored) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the GTS initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

    Result 
    Result
    Proceed to
    DTC P2445 is output
    A
    No pending DTC
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4. CHECK VACUUM HOSES (AIR PRESSURE SENSOR - AIR SWITCHING VALVE)
  1. Check the vacuum hose connections with the air pressure sensor and air switching valve.

  1. Inspect the vacuum hose for blockages and damage.

    OK:
    Vacuum hose has no blockages or damage.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


5. INSPECT AIR PRESSURE SENSOR

  1. A263362
    Connect a pressure gauge to the air pressure sensor as shown in the illustration.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).

  1. Check that the pressure displayed on the GTS fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The GTS displays the air pump pressure (Air Pump Pressure (Absolute)) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR (Click here)
OK


6. CHECK SECONDARY AIR INJECTION SYSTEM PIPE CONNECTIONS
A261569
  1. Check that all the pipes and hoses between the air pump and air switching valve are securely connected.

  1. Inspect the pipes and hoses for blockages and damage.

    OK:
    Secondary air injection system piping has no blockages or damage.



NG
REPAIR OR REPLACE SECONDARY AIR INJECTION SYSTEM PIPING
OK


7. INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A115629E07
  1. Disconnect the air injection control driver connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B14-1 (BATT) - Body ground
    Always
    11 to 14 V
    B12-5 (+B) - Body ground
    Ignition Switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B12-1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Injection Driver)



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


8. CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B94-20 (AIRP) - B12-4 (SIP)
    Always
    Below 1 Ω
    B94-20 (AIRP) or B12-4 (SIP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. INSPECT AIR PUMP ASSEMBLY
A222978E02
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the 400 A probe of an ammeter to the (+) wire of the air pump.

    Text in Illustration 
    *1
    Air Pump Wire
    *2
    Air Injection Control Driver

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN and AIR PUMP: OFF, ASV: CLOSE.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Measure the current while the air pump is on and off.

    Standard Current:
    GTS Operation
    Air Pump
    ASV
    Specified Condition
    AIR PUMP: ON, ASV: OPEN
    ON
    OPEN
    10 to 40 A
    AIR PUMP: OFF, ASV: CLOSE
    OFF
    CLOSE
    Below 1 A

    NOTICE:
    1. This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
      Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
      While AIR system operation using the GTS is prohibition (WAIT or ERROR).
      If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.
    2. Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected. Wait for 7 minutes with the ignition switch turned to ON or the engine running.
    4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 13
OK


10. PERFORM ACTIVE TEST USING GTS
  1. Disconnect the air injection control driver connector.

  1. A229922E46
    Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-3 (SIV) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. A229922E47
    Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-4 (SIP) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


11. REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


12. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear DTCs (if stored) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the GTS initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END

13. REPLACE AIR PUMP ASSEMBLY
  1. Replace the air pump assembly (Click here).


NEXT


14. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear DTCs (if stored) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the GTS initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
Go to step 15
OK

END

15. PERFORM ACTIVE TEST USING GTS
  1. Disconnect the air injection control driver connector.

  1. A229922E46
    Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-3 (SIV) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V

  1. A229922E47
    Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration 
*1
Air Injection Control Driver
*2
ECM
*a
Front view of wire harness connector
(to Air Injection Control Driver)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

    HINT:
    When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the secondary air injection system intrusive operation while the engine is idling.

  1. Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.

  1. Turn the ignition switch off.

    NOTICE:
    1. Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
    2. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
    3. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.


    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B12-4 (SIP) - B12-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


16. REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver.


NEXT


17. CHECK WHETHER DTC OUTPUT RECURS (DTC P2445)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear DTCs (if stored) (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

  1. Start the engine after the GTS initialization is finished.

  1. Perform the System Check operation by pressing Next.

  1. After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END


← P2445 Secondary Air Injection System Pump Stuck Off Bank1 (Dec 2015 – Mar 2016)P2445 Secondary Air Injection System Pump Stuck Off Bank1 (Jan 2017 – Nov 2017) →